RAV4
01 Install D/C Cut Fuse – see page 2 ..................................
02 Install antenna* ................................................................

FUNCTIONAL OPERATION
Apply parking brake and cycle ignition “IG-ON”; place gear selector in reverse;
turn on lights and rear defogger. Unlock doors; release fuel door.

01
02
03
04
05
06
07
08
09
10
11

Check dome, courtesy, map, and sun visor lights ...........
Check warning/indicator lights, gauges, and horn ...........
Check windshield wipers and washers ............................
Check headlights, instrument lights, turn signals,
emergency flashers, and brake lights ..............................
Check inside/outside rear view mirror operation/
adjustment* .....................................................................
Check cigarette lighter* and power outlets ......................
Check audio/navigation*/backup camera* systems and
set clock ..........................................................................
Verify Entune/Navigation software version (Display
Audio, Non-HDD Type only)* ........................................
Check sliding roof* .........................................................
Check Rear Seat Entertainment System operation* ........
Install shift-lock override button cover ............................

WALKAROUND INSPECTION
Start at left front door. Check window and door lock operation (from master power
switch, if equipped). Continue around vehicle in a counterclockwise direction
checking each door and window operation, child door locks, seat belts, interior
condition, all lights, luggage compartment contents. Finish by checking headlight
aim and continue into UNDER HOOD checks.

01 Check Smart Key System*............................................
02 Check door and door lock operation, including each
wireless remote control/theft deterrent system* ..............
03 Check window operation .................................................
04 Check that engine starts with all keys ............................
05 Check that child safety door locks are in normal
(unlocked) position ..........................................................
06 Check seats and seat belt operation ...............................
07 Check rear defogger/rear view mirror defogger* .............
08 Check side marker, tail, backup, cargo*, and license
plate lights ......................................................................
09 Check luggage compartment light* and trim appearance
10 Check spare tire pressure, inspect for damage, and
check jack and tool installation ........................................
11 Check headlight aim ........................................................

UNDER VEHICLE (ON HOIST)
01 Remove disc brake anti-rust covers/anti-corrosion
wheel film* .....................................................................
02 Inspect tires for defects/damage .....................................
03 Initialize Tire Pressure Warning System (TPWS) - see
page 2 ............................................................................
04 Install wheel covers/caps/spare tire wheel covers* ........
05 Inspect for fuel, oil, coolant, and other fluid leaks ...........
06 Inspect under the vehicle for damage, rust, etc. ..............
07 Visually check bolts and nuts on chassis and powertrain
for looseness ...................................................................
08 Install rubber body plugs* (stored in glove box or center
console)...........................................................................

ROAD TEST
A complete road test helps assure customer satisfaction. Drive vehicle over a
variety of road surfaces and driving conditions. Check for unusual noise and
driving performance.
Enter Odometer Readings
Reading Before Test: _______________ Reading After Test: ________________

01
02
03
04
05
06
07
08
09
10
11

Check cold engine operation ...........................................
Check engine operation during warm-up .........................
Check engine at normal operating temperature ..............
Check automatic transmission operation .........................
Check brake and parking brake operation .......................
Check steering operation & off-center/vehicle pull/flutter .
Inspect for abnormal noise and vibration .........................
Inspect for squeaks and rattles ........................................
Check front and rear* heater and A/C operation..............
Check cruise control operation* ......................................
Check front seat heater/ventilation operation* .................

FINAL INSPECTION AND CLEANING

Check engine oil and ATM fluid levels .............................
Check brake and power steering fluid levels ...................
Check engine coolant level ..............................................
Check windshield washer fluid level ................................
Check battery state-of-charge using Digital Battery
System Analyzer (SOC Reading: ___________%) .....
06 Inspect for fuel, oil, coolant, and other fluid leaks ............

01 Remove interior protective covers, unnecessary labels,
tags, etc. (Remove just before delivery to customer).......
02 Visually inspect all interior parts for installation,
damage, fit, dirt, etc. ........................................................
03 Verify floor mat application and install using
retaining clips* ...............................................................
04 Remove Rapgard™ and clear protective bumper film*....
05 Wash and clean vehicle ...................................................
06 Inspect paint finish for scratches, chips, rust, dents,
damage, etc. ....................................................................
07 Inspect exterior body parts for proper installation,
damage, rust, etc. ............................................................
08 Place oil change sticker on inside of windshield, top
left corner ........................................................................
09 Place Owner’s Guide & first aid kit portfolio* in glove box
10 Perform Techstream Health Check ................................
11 Install front license plate and mounting bracket - see
page 2 .............................................................................

* Inspect or install when equipped/required.

COMMENTS:

UNDER HOOD
01
02
03
04
05

OK

December 2012
Adjust/
Adjust/
Repair
Repair

OK

BEFORE INSPECTION

Adjust/
Repair

2013 PRE-DELIVERY SERVICE CHECK SHEET

Completion and retention of this from is required to comply with Toyota’s Warranty Policy.

TECHNICIAN’S SIGNATURE

SERVICE MANAGER’S SIGNATURE

NAME (PLEASE PRINT)

NAME (PLEASE PRINT)

Date

Dealer Name

Dealer Code

We hereby certify that all items
on this form have been checked
and corrected for proper
operation as required.
Vehicle Identification Number (Sticker)

D/C CUT FUSE INSTALLATION
To minimize battery discharge the D/C Cut Fuse has been removed
and is stored in the engine compartment Relay Block. Install the D/C
Cut Fuse and confirm all related DTCs are cleared.

2 Install D/C Cut Fuse Here

1 D/C Cut Fuse Storage Location

TPWS INITIALIZATION
Refer to the Repair Manual for the Initialization Procedure.
NOTE
• Please note the spare tire does NOT have a TPWS sensor.
• If performing this procedure in areas with temperatures significantly colder or warmer than shop temperature,
follow the procedures outlined in Service Bulletin No. T-SB-0020-12, “Tire Inflation Pressure Compensation and
Adjustment”.

FRONT LICENSE PLATE & MOUNTING BRACKET INSTALLATION
1. Align holes “A” of the mounting bracket with the dimples on
the front bumper cover. Mark the location of holes “B” on
the front bumper cover.

A

1

B

B

A

NOTE
• Holes “A” are used for installation of the mounting bracket to
the bumper cover.

• Holes “B” are used for the installation of the front license plate
to the mounting bracket.

2. Drill two relief holes with a diameter of 11 mm (0.43 in.) at
the hole “B” marks on the front bumper cover to prevent the
license page retaining bolt end from contacting cover.

2
1

NOTICE
Do NOT drill at the dimples on the front bumper cover.

4
6

3. Install the mounting bracket to the front bumper cover by
attaching the two self-tapping screws into the dimples.
4. Install the front license plate to the mounting bracket using
bolts with the following measurements:
Length: 15.0 - 23.0 mm (0.59 - 0.91 in.)
Diameter: 6.0 mm (0.24 in.)
Pitch: 1.0 mm (0.04 in.)

5
1 Mounting Bracket
2 Dimples
3 Mark and Drill Holes

3

4 Self-Tapping Screws
5 License Plate
6 Bolts