CAMRY HV
01 Install Short Pin* (Hawaii, Puerto Rico, Saipan, Guam,
American Samoa) ............................................................

FUNCTIONAL OPERATION
Apply parking brake and cycle ignition “IG-ON”; place gear selector in reverse;
turn on lights and rear defogger. Unlock doors; release fuel door.

01
02
03
04
05
06
07
08
09
10

Check dome, courtesy, map, and sun visor lights* ..........
Check warning/indicator lights, gauges, and horn ...........
Check windshield wipers and washers ............................
Check headlights, instrument lights, turn signals,
emergency flashers, and brake lights ..............................
Check inside/outside rear view mirror operation/
adjustment* ......................................................................
Check cigarette lighter* and power outlets.......................
Check audio/navigation*/backup camera* systems and
set clock ...........................................................................
Verify Entune/Navigation software version (Display
Audio, Non-HDD Type only)* ........................................
Check sliding roof* ..........................................................
Install shift-lock override button cover .............................

WALKAROUND INSPECTION
Start at left front door. Check window and door lock operation (from master power
switch, if equipped). Continue around vehicle in a counterclockwise direction
checking each door and window operation, child door locks, seat belts, interior
condition, all lights, luggage compartment contents. Finish by checking headlight
aim and continue into UNDER HOOD checks.

01 Check Smart Key System .............................................
02 Check door and door lock operation, including each
wireless remote control/theft deterrent system* ...............
03 Check window operation..................................................
04 Check that engine starts with all keys .............................
05 Check that child safety door locks are in normal
(unlocked) position ..........................................................
06 Check seats and seat belt operation ...............................
07 Check rear defogger/rear view mirror defogger* ..............
08 Check side marker, tail, backup, and license plate lights
09 Check luggage compartment light* and trim appearance
10 Adjust spare tire pressure, inspect for damage, and check
jack and tool installation ....................................................
11 Check headlight aim ........................................................

UNDER HOOD
01
02
03
04
05
06

Check engine oil level .....................................................
Check brake fluid level ....................................................
Check engine coolant level ............................................
Check inverter coolant level ...........................................
Check windshield washer fluid level ................................
Check battery state-of-charge using Digital Battery
System Analyzer (SOC Reading: ___________%) .....
07 Inspect for fuel, oil, coolant, and other fluid leaks ...........

BATTERY MAINTENANCE
01 Perform HV battery check and maintenance ..............
* Inspect or install when equipped/required.

UNDER VEHICLE (ON HOIST)

Adjust/
Repair

December 2012

OK

OK

BEFORE INSPECTION

Adjust/
Repair

2013 PRE-DELIVERY SERVICE CHECK SHEET

01 Remove disc brake anti-rust covers/anti-corrosion
wheel film* ......................................................................
02 Inspect tires for defects/damage ......................................
03 Verify Tire Pressure Warning System (TPWS) operation see page 2 ......................................................................
04 Install wheel covers/caps/spare tire wheel covers* .........
05 Check hybrid transmission fluid level ..............................
06 Inspect for fuel, oil, coolant, and other fluid leaks ...........
07 Inspect under the vehicle for damage, rust, etc. ..............
08 Visually check bolts and nuts on chassis and powertrain
for looseness....................................................................
09 Install rubber body plugs (stored in glove box or center
console)* ..........................................................................
10 Install front wheel opening extension pads - see page 2

ROAD TEST
A complete road test helps assure customer satisfaction. Drive vehicle over a
variety of road surfaces and driving conditions. Check for unusual noise and
driving performance.
Enter Odometer Readings
Reading Before Test: _______________ Reading After Test: ________________

01
02
03
04
05
06
07
08
09
10
11
12
13

Check cold engine operation............................................
Check engine operation during warm-up .........................
Check engine at normal operating temperature ...............
Check hybrid transmission operation ..............................
Check brake and parking brake operation .......................
Check steering operation & off-center/vehicle pull/flutter .
Inspect for abnormal noise and vibration .........................
Inspect for squeaks and rattles ........................................
Check Blind Spot Monitor System* .................................
Check front and rear* heater and A/C operation ..............
Check cruise control operation* ......................................
Check front seat heater/ventilation operation* .................
Set/calibrate compass* - see page 2 ...............................

FINAL INSPECTION AND CLEANING
01 Remove interior protective covers, unnecessary labels,
tags, etc. (Remove just before delivery to customer) .......
02 Visually inspect all interior parts for installation,
damage, fit, dirt, etc. ........................................................
03 Verify floor mat application and install using
retaining clips* ...............................................................
04 Verify green light is illuminated on SOS (Safety Connect)
button* .............................................................................
05 Remove Rapgard™ and clear protective bumper film* ....
06 Wash and clean vehicle ...................................................
07 Inspect paint finish for scratches, chips, rust, dents,
damage, etc. ....................................................................
08 Inspect exterior body parts for proper installation,
damage, rust, etc. ............................................................
09 Place oil change sticker on inside of windshield, top
left corner .........................................................................
10 Place Owner’s Guide & first aid kit portfolio* in glove box
11 Perform Techstream Health Check .................................
12 Install front license plate & mounting bracket* - see page 2

Completion and retention of this from is required to comply with Toyota’s Warranty Policy.

TECHNICIAN’S SIGNATURE

SERVICE MANAGER’S SIGNATURE

NAME (PLEASE PRINT)

NAME (PLEASE PRINT)

Date

Dealer Name

Dealer Code

We hereby certify that all items
on this form have been checked
and corrected for proper
operation as required.
Vehicle Identification Number (Sticker)

FRONT WHEEL OPENING EXTENSION PAD INSTALLATION
The front wheel opening extension pad set (right and left front
wheel opening extension pads and 2 tapping screws) is loaded
in the luggage compartment at the assembly plant to avoid
damage in transit.
1. Remove the 2 tapping screws form the engine under cover
(the screws will be reused for installation).
2. Place the left front wheel opening extension pad on the
installation position as shown and tighten the 3 tapping
screws.

1

1

2

NOTE
• There is a distinguishable mark on each pad.
• Do not interchange the tapping screws A and B.
3. Repeat steps 1 and 2 for the right side.
Tapping Screws A:
Nominal length: 23.0 mm (0.91 in.)
Diameter: 6.0 mm (0.24 in.)
Washer outside diameter: 18.0 mm (0.71 in.)

2

1 Screw A
2 Screw B

Tapping Screws B:
Nominal length: 16.0 mm (0.63 in.)
Diameter: 6.0 mm (0.24 in.)
Washer outside diameter: 20.0 mm (0.79 in.)

1

COMPASS CALIBRATION
Refer to the Repair Manual for the Calibration procedure for vehicles equipped with a compass in the rear view mirror.
NOTE
• Do NOT perform calibration of the compass in a place where the earth’s magnetic field is subject to interference (underground
parking, under a steel tower, between buildings, roof parking, near a railroad crossing, near a large vehicle, etc.).
• During calibration, do NOT operate electric systems (moon roof, power windows, etc.) as they may interfere with the calibration.

TPWS OPERATION VERIFICATION
1. Connect Techstream to DLC3.
2. Adjust all tires (except the spare tire) to the standard tire inflation pressure, as indicated on the tire and loading
information label on the vehicle.
NOTE
• To adjust tire pressure correctly when outside temperature is significantly colder or warmer than shop temperature, follow the
procedures outlined in Service Bulletin No. T-SB-0020-12, “Tire Inflation Pressure Compensation and Adjustment”.
• Adjust the tire pressure when the tires are cold.
3. Cycle the ignition switch to the “IG-ON” mode.
4. Check the tire pressure of all tires using Techstream. If the tire pressure values cannot be displayed, the system is
NOT operating properly. Refer to the Repair Manual.

FRONT LICENSE PLATE & MOUNTING BRACKET* INSTALLATION
Installation Procedure
Part Number: 52114-06160
1. Insert the front license plate into the mounting bracket.
2. Align the center tab on the mounting bracket with the center
line of the air intake.
3. Attach the hooks of the mounting bracket to the second air
intake opening and rotate the bracket upwards.
4. Align the installation holes on the mounting bracket and front
license plate with the dimples on the front bumper.
5. Screw in the 2 self-tapping screws directly into the dimples to
install the front license plate and mounting bracket.
NOTICE
• Do NOT pre-drill holes into the bumper.
• Do NOT over-tighten the self-tapping screws.

1 Air Intake
2 Hooks
3 Front License Plate
Mounting Bracket
4 Tab
5 Rotate Bracket

5
1

2
3
4

1

1 Dimples
2 Front License Plate
Mounting Bracket
3 License Plate
4 Self-tapping Screws

2
3
4