January 10, 2013

T-SB-0009-13

2013 RAV4 EV Pre-Delivery Service (PDS)
Service
Category

General

Section

Pre-Delivery Service

Market

USA

Applicability
YEAR(S)

MODEL(S)

2013

RAV4 EV

ADDITIONAL INFORMATION

Introduction

Pre-Delivery Service (PDS) is a critical step in satisfying our new car customers. Customer feedback
indicates the following areas deserve special attention when performing PDS:
• Careful inspection for paint chips/scratches and body dents/dings.
• Proper operation of electrical accessories (including interior light, clock, and radio reset).
• Interior cleanliness.
• Proper function of mechanical systems.
A new PDS Check Sheet has been developed for the 2013 model year RAV4 EV. Some check points
have been added, expanded or clarified. Bulletins are available for items in bold type.
Warranty Policy

If the need for additional repairs or adjustment is noted during the Pre-Delivery Service, the required
service should be performed under warranty. Reimbursement will be managed under the warranty
policy.
The Warranty Policy and Procedures Manual requires that you maintain the completed PDS
check sheet in the customer’s file. If you cannot produce a completed form for each retailed
vehicle upon TMS and/or Region/Distributor audit, the PDS payment amount will be subject to debit.
An additional Repair Order completed in conjunction with normal PDS must have time punch/flags
for service. If multiple repairs are performed, separate time flags must be punched for each repair.
Reimbursement Information
OP CODE

DESCRIPTION

TIME

OFP

T1

T2

001013

Pre-Delivery Service (PDS)

1.0

N/A

N/A

N/A

© 2013 Toyota Motor Sales, USA

Page 1 of 6

January 10, 2013

T-SB-0009-13

Page 2 of 6

2013 RAV4 EV Pre-Delivery Service (PDS)

Required Tools & Equipment
REQUIRED EQUIPMENT

SUPPLIER

PART NUMBER

QTY

ADE

TSPKG1
or
TSLITEDLR01

1

TIS Techstream*
or
Techstream Lite
NOTE: Software version 7.31.003 or later is required.
* Essential SST.

NOTE
Additional Techstream units may be ordered by calling Approved Dealer Equipment (ADE) at
1-800-368-6787.

Before Inspection

When performing new car Pre-Delivery Service, install Short Pin before moving vehicle from storage
lot so that FUNCTIONAL OPERATION checks can begin as soon as vehicle is moved into service
stall.
1. Install Short Pin – see check sheet
2. Install antenna*
Functional Operation

Apply parking brake and cycle the Start/Stop switch to "Ready" On, place gear selector in reverse,
turn on lights and rear defogger, unlock all doors, release battery charger door.
1. Check dome, courtesy, map, and sun visor lights
2. Check warning/indicator lights, gauges, and horn
3. Check windshield wipers and washers
4. Check headlights, instrument lights, turn signals, emergency flashers, and brake lights
5. Check inside/outside rear view mirror operation/adjustment
6. Check cigarette lighter* and power outlets
Check the power outlet using an electrical accessory designed for this use.

© 2013 Toyota Motor Sales, USA

January 10, 2013

T-SB-0009-13

Page 3 of 6

2013 RAV4 EV Pre-Delivery Service (PDS)

Functional Operation (Continued)

7. Check audio/navigation*/backup camera* systems and set clock
For navigation, set the destination search area to local position
8. Check sliding roof*
Walkaround Inspection

Starting at the left front door, check window and door lock operation and the operation of all power
windows and door locks from master switch, on vehicles so equipped. While walking around vehicle
in a counterclockwise direction, open left rear door (if applicable) and check operation of window
regulator and door lock, set child safety door locks to the normal (unlocked) position. Assure
tightness of interior garnishes and check seat belts. Inspect lights at rear of vehicle. Repeat checks
at right rear door. Inspect right front door window regulator and lock operation and garnishes. Check
seats and seat belt operation. Continue on around to the front of the vehicle checking lights.
1. Check Smart Key System* – T-SB-0015-12
2. Check window operation
3. Check that child safety door locks are in normal (unlocked) position
4. Check seats and seat belt operation
5. Check rear defogger/rear view mirror defogger*
6. Check side marker, tail, backup, and license plate lights
7. Check luggage compartment light* and trim appearance
8. Check headlight aim
Refer to the Repair Manual for procedures.
Under Hood

1. Check brake and power steering fluid levels
Visually inspect using see-through reservoirs.
2. Check battery system coolant level (blue; right side)
3. Check motor system coolant level (blue; left side)
4. Check heater system coolant level (pink; right side)
NOTE
Use caution when adding coolant to vehicle. Ensure that the two coolant types do not get
mixed.

© 2013 Toyota Motor Sales, USA

January 10, 2013

T-SB-0009-13

Page 4 of 6

2013 RAV4 EV Pre-Delivery Service (PDS)

Under Hood (Continued)

5. Check windshield washer fluid level
6. Check auxiliary battery state-of-charge using Digital Battery System Analyzer
Refer to Service Bulletin No. PG001-06, “Battery Maintenance for In-Stock Vehicles &
Pre-Delivery.”
NOTE
Battery SOC should be a minimum of 75%. Please enter the SOC Reading on the space
provided on the check sheet and attach the printout to the check sheet.

7. Inspect for coolant and other fluid leaks
Under Vehicle (On Hoist)

1. Remove disc brake anti-rust covers/anti-corrosion wheel film* – PD017-04
Visually inspect rotors for rust.
NOTE
For best rotor rust prevention, retain wheel film on vehicle until just prior to customer delivery.

2. Inspect tires for defects/damage
3. Tire Pressure Warning System (TPWS) confirmation – see check sheet
4. Install wheel covers/caps/spare tire wheel covers*
5. Inspect for coolant and other fluid leaks
6. Inspect under the vehicle for damage, rust, etc.
7. Visually check bolts and nuts on chassis and powertrain for looseness
8. Install rubber body plugs* (stored in glove box or console)
Road Test

A complete road test helps assure customer satisfaction. Drive vehicle over a variety of road
surfaces and driving conditions. Check for unusual noise and driving performance.
1. Check electric motor operation
Check performance over a broad range of driving conditions, including acceleration, cruise, and
deceleration (including Brake Regeneration mode).

© 2013 Toyota Motor Sales, USA

January 10, 2013

T-SB-0009-13

Page 5 of 6

2013 RAV4 EV Pre-Delivery Service (PDS)

Road Test (Continued)

2. Check gear selector operation
Check gear selector operation, including operation in each range, neutral start switch, and
shift lock system.
3. Check brake and parking brake operation
Check brake function, including unusual noise, parking brake performance, and all related
brake system indicator lights.
4. Check steering operation and off-center/vehicle pull/flutter
Check steering function.
Check steering off-center/vehicle pull/flutter.
5. Inspect for abnormal noise and vibration
6. Inspect for squeaks and rattles
7. Check front and rear* heater and A/C operation
8. Check cruise control operation*
Check cruise control, including On-Off switch, “SET/COAST,” “RESUME/ACCEL,” and “CANCEL”
functions.
9. Check front seat heater/ventilation operation*
Final Inspection & Cleaning

1. Remove interior protective covers, unnecessary labels, tags, etc. (Remove protective covers
just before delivery to the customer)
Remove plastic covers from door panels, seats, head restraints, and sun visors, as required.
Remove labels, tags, and stickers (except those containing owner information).
NOTE
Consumer information labels, such as airbag information warning and bumper information
labels, MUST be left on the vehicle until delivery to a retail customer.

2. Visually inspect all interior parts for installation, damage, fit, dirt, etc.
3. Verify floor mat application and install using retaining clips* – T-SB-0024-12
4. Verify the green light is illuminated on SOS (Safety Connect) button*
5. Remove Rapgard™ and clear protective bumper film*
Ensure that ALL glue residue is removed.
© 2013 Toyota Motor Sales, USA

January 10, 2013

T-SB-0009-13

Page 6 of 6

2013 RAV4 EV Pre-Delivery Service (PDS)

Final Inspection & Cleaning (Continued)

6. Wash and clean vehicle
7. Inspect paint finish for scratches, chips, rust, dents, damage, etc.
8. Inspect exterior body parts for proper installation, damage, rust, etc.
9. Place Owner’s Guide and first aid kit portfolio* in glove box
10. Install front license plate and mounting bracket – see check sheet
11. Perform Techstream Health Check
Perform Health Check to ensure that diagnostic trouble codes are not present. Health Check
results can be printed for the customer at delivery, or for the dealer file, using the Diagnostic
Report function.
12. Fully Charge EV battery – T-SB-0001-13
*Inspect or install when equipped or required

© 2013 Toyota Motor Sales, USA