GP) TOYOTA

T-SB-0020-13 February 8, 2013 Technical Service Bulletin

Smart Key System Check During PDS

Service
Category General
Toyota Supports =
Section _Pre-Delivery Service Market USA ASE Certfication +
Applicability
YEAR(S) MODEL(S) ADDITIONAL INFORMATION
2014 4Runner, Avaton,

Avalon HV, Camry,
Camry HV, Highlander,
Highlander HV, Land
Cruiser, Prius, Prius
C, Prius PHY, Prius
V, RAV4, Sequoia,
Sienna, Venza

Introduction

Some 2014 model year vehicles are equipped with a Smart Key system, which allows the customer
to enter and start the vehicle without using a mechanical key. To ensure the system is operating
properly, the Smart Key functions (Smart Entry and Smart Start) should be inspected during
Pre-Delivery Service (PDS). The following inspection procedure has been developed to confirm the
proper operation of the Smart Key system prior to vehicle delivery.

NOTE
Check all of the Smart Keys using this procedure.

Warranty Information

OP CODE DESCRIPTION TIME OFP 1 T2
N/A Not Applicable to Warranty - - - -

© 2013 Toyota Motor Sales, USA Page 1 of §

@ TOYOTA T-SB-0020-13 February 8, 2013 Page 2 of 5

Smart Key System Check During PDS

Inspection Procedure

1. Remove ALL Smart Keys from the vehicle.

NOTE
The remaining keys need to be a minimum of 3 feet (1 meter) away from the vehicle.

2. Check Smart Entry function at all the doors.

NOTE
Smart Key MUST be in actuation area No. 1 for this check (see Figure 1 below).

Figure 1.

[+] 4 door Sensor Vehicles 2 | 2Door Sensor Vehicles

© 2013 Toyota Motor Sales, USA

@TOYOTA T-SB-0020-13 February 8, 2013 Page 3 of 5

Smart Key System Check During PDS

Inspection Procedure (Continued)
A. Locking operation:

Push the lock button on the outside door handle. All the doors should lock simultaneously.
At this time, one beep will be heard and the turn signal lights will flash once.

B. Unlocking operation:

NOTE
After checking the lock function, wait at LEAST 3 seconds before checking the unlock
function.

Grasp the outside door handle (sensors are located on the underside of the door handles).
At this time, two beeps will be heard and the turn signal lights will flash twice.

NOTE

Only the driver’s door unlocks when the driver's door handle is grasped. All the doors
unlock when any door handie other than the driver's door handle is grasped.

3. Check the Wireless Door Lock function.

Using the remote outside of the vehicle, confirm that all doors can be locked and unlocked
using the wireless remote.

© 2013 Toyota Motor Sales, USA

@ TOYOTA T-SB-0020-13 February 8, 2013 Page 4 of §

Smart Key System Check During PDS

Inspection Procedure (Continued)

4. Check Smart Start function from inside the vehicle.

NOTE
Smart Key MUST be in actuation area No. 2 for this check (see Figure 2 below).

Figure 2.

[+] 4 door Sensor vehicles | — [2 [20008 sensor vehicies |

A. Check for proper activation of the “ENGINE START/STOP” switch.

(1) Make sure the gear selector lever is in the “P” position.

© 2013 Toyota Motor Sales, USA

QPTOYOTA

T-SB-0020-13

Smart Key System Check During PDS

February 8, 2013

Page 5 of 5

Inspection Procedure (Continued)

Figure 3. Engine Start/Stop Switch

eS
oar —> Age — 'sgn

eee

(2) Without depressing the brake pedal,
press the “ENGINE START/STOP” switch
and confirm the mode changes property.
From the “OFF” mode:

+ Press once. The power supply mode
is in the “ACC” mode.

+ Press twice. The power supply
mode is in the “IG-ON” mode.

+ Press three times. The power supply
mode is in the “OFF” mode.

NOTE 7 | Light of
if the “ENGINE START/STOP” switch 2 | wont on
illuminator blinks in amber, refer to e

the Repair Manual.

B. Check the engine start/stop operation.

(1) Make sure that the gear selector lever is in the “P” position.

(2) When depressing the brake pedal, check that the green engine switch illuminator
cames on, and push the “ENGINE START/STOP” switch to start the engine.

(3) Push the switch again to stop the engine.

NOTE

When the “ENGINE START/STOP” switch is turned OFF with the gear selector lever in a
position other than “P,” the vehicle electrical system will be in the “ACC” mode. When
the door is opened the Smart Key System Warning Buzzer will sound indicating that the
electrical system is not “OFF” when exiting the vehicle. This may result In a discharged
battery. Be sure to turn OFF the engine AFTER shifting the gear selector lever to the “P”
position.

Checking Procedure:
* Shift the gear selector lever to the “P” position (or check that the gear selector lever
is in the “P” position).

* Press the “ENGINE START/STOP” switch once and check that the indicator light goes
OFF.

5. Repeat steps 2 — 4 with each Smart Key.

© 2013 Toyota Motor Sales, USA