NHTSA ID Number: 10133444
Manufacturer Communication Number: Emissions Recall
TSB/Document Date: 2018-04-16
Summary
3.0L TDI vehicles were equipped with undisclosed Auxiliary Emission Control Devices which are not permitted by emissions regulations. Install updated engine control module (ECM) software, transmission control module (TCM) software and hardware to bring affected vehicles into regulatory compliance. Updated resale information included.
Emissions Recall
Code: 23V6
REVISION
Subject
Release Date
Revision Summary
Affected Vehicles
3.0L TDI Engine Emissions System Modification
November 29, 2017
Updated resale information included.
U.S.A.:
2013-2014 MY Volkswagen
Touareg 3.0L TDI Generation 2.1
Check Campaigns/Actions screen in Elsa on the day of repair to verify that a VIN qualifies for repair under this
action. Elsa is the only valid campaign inquiry & verification source.
Campaign status must show “open.”
If Elsa shows other open action(s), inform your customer so that the work can also be completed at
the same time the vehicle is in the workshop for this campaign.
Problem Description
3.0L TDI vehicles were equipped with undisclosed Auxiliary Emission Control Devices which
are not permitted by emissions regulations.
Corrective Action
Install updated engine control module (ECM) software, transmission control module (TCM)
software and hardware to bring affected vehicles into regulatory compliance.
Code Visibility
On or about November 6, 2017, affected vehicles were listed on the Inventory Vehicle Open
Campaign Action report under My Dealership Reports. A list was not posted for dealers who did
not have any affected vehicles. The campaign code showed open on affected vehicles in Elsa
and affected vehicles are identified with this campaign code in the VIN Lookup tool at
www.vw.com.
Owner Notification
Loaner/Rental Vehicle
– REQUIRED!
Owner notification took place on November 6, 2017.
To remain compliant with the Settlement Agreement, Service Consultants must complete a
Loaner/Rental label and it must be signed by the customer. This documents each customer’s
decision to accept or decline the offer for a loaner or rental vehicle while the Approved
Emissions Modification was being performed on their vehicle.
Affix the completed label to the Repair Order and follow the new photo documentation
requirements for this label in the IN-FORM tool.
Emissions Campaigns
Requirements
(CALIFORNIA ONLY)
The California Air Resources Board and the Department of Motor Vehicles (DMV) require
emissions-related campaigns to be completed prior to vehicle registration renewal. When
campaign work is done you must provide the owner with a signed “Vehicle Emission Recall –
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen
dealer. 2017 Volkswagen
Group of America, Inc. All Rights Reserved.
November 2017
23V6 Page 1 of 39
Proof of Correction” certificate (RC EMISCAVWAU). Order certificates online via the
Compliance Label Ordering portal at www.vwhub.com.
Additional Information
Please alert everyone in your dealership about this action, including Sales, Service, Parts
and Accounting personnel. Contact Warranty if you have any questions.
Fill out and affix the appropriate TDI Recall Proof of Completion label and the appropriate
Supplemental Vehicle Emissions Control Information Label after work is complete. Additional
shipments will be released based on the volume of completed repairs claimed through
SAGA. The parts will not be available for order through the website at this time.
The information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These procedures
are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To determine whether
this information applies, contact an authorized Volkswagen
dealer. 2017 Volkswagen
Group of America, Inc. All Rights Reserved.
November 2017
23V6 Page 2 of 39
Claim Entry Instructions
After campaign has been completed, enter claim as soon as possible to help prevent work from being duplicated
elsewhere. Attach the Elsa screen print showing action open on the day of repair to the repair order.
If customer refused campaign work:
U.S. dealers: Submit request via WISE under the Campaigns/Update/Recall Closure option.
Service Number
23V6
Damage Code
0099
Parts Vendor Code
Claim Type
Causal Indicator
Vehicle Wash/Loaner
Criteria I.D.
WWO
Sold vehicle: 7 10
Mark 3.0L Gen 2.1 Kit as causal*
Do not claim vehicle wash/loaner under this action
01
Install 3.0L Gen 2.1 Kit, install Glow Plug with Combustion Chamber Pressure Sensor,
Top off AdBlue tank, and *install a supplemental Vehicle Emissions Control Information
label and TDI Emissions Modification Proof of Completion Label.
Labor operation: 2674 19 99
Quantity
1.00
1.00
Part Number
7P0298099 X
059905061H
Up to 11.00
G 052910A2
155 T.U.
Description
3.0L Gen 2.1 Kit*
Glow Plug with Combustion Chamber Pressure
Sensor
AdBlue (one bottle = 0.5 gallon/ 1.89 Liter)
--AND-Connect battery charger.
Labor operation: 2706 89 50
10 T.U.
--AND-Connect vehicle diagnostic tester, perform software update for control unit.
Labor operation: 2360 22 99
Time stated on diagnostic protocol
(Maximum 60 T.U.)
--AND-Follow IN-FORM tool app.
Labor operation: 0183 00 99
20 T.U.
*Labels are sent free of charge. They cannot be charged to this campaign.
LOANER/RENTAL claiming on next page
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen
dealer. 2017 Volkswagen
Group of America, Inc. All Rights Reserved.
November 2017
23V6 Page 3 of 39
– LOANER/RENTAL MUST BE CLAIMED ON A SEPARATE LINE –
DO NOT PUT ON CAMPAIGN CLAIM
LOANER/RENTAL
Claim Type: A1A
Service #: CU01
Damage Code: 0010
Removed Part : MOB
Outside LO Number : CU010000
DO NOT PUT LOANER/RENTAL ON CAMPAIGN CLAIM
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen
dealer. 2017 Volkswagen
Group of America, Inc. All Rights Reserved.
November 2017
23V6 Page 4 of 39
Campaign Work Procedure
23V6 Emissions Recall
At this time, affected new and used vehicles in dealer inventory are not
included in this emissions modification release.
NOTE
Damages resulting from improper repair or failure to follow these work instructions are the dealer’s responsibility
and are not eligible for reimbursement under this action.
Required Parts
Quantity
1
1
up to 19.5L
Part Description
3.0L Gen 2.1 Kit
Glow Plug with Combustion Chamber Pressure Sensor
AdBlue
Part Number
7P0298099 X
059905061H
Any, as required
IMPORTANT!
AdBlue Ordering Information
Any AdBlue part number in any quantity/volume is acceptable for use.
For claiming purposes, for every 0.5 gallons of AdBlue used, one unit of G 052910A2 should be
entered onto the SAGA claim regardless of which AdBlue part number was used.
Required Labels
Quantity
1
Part Description
TDI Proof of Completion Label
1
VECI Label
1
VECI Label
Part Number
7P0 010 023 B
--AND-059 010 533 BD
--OR-059 010 533 BE
Vehicle
MY 2013 and 2014 Touareg
MY 2013 Touareg
MY 2014 Touareg
IMPORTANT!
Maintaining Your TDI Campaign Label Supply
SAGA claims count! Warranty Administrators should enter TDI claims promptly to ensure
labels can be allocated to support future repairs.
TDI Labels are allocated daily, free of charge, based on the count of TDI claims entered in
SAGA.
TDI labels cannot be ordered through the Compliance Label Ordering Portal. If you have
questions, please email labelrequest@vw
.com.
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen
dealer. 2017 Volkswagen
Group of America, Inc. All Rights Reserved.
November 2017
23V6 Page 5 of 39
Required Tools
VAS6150X - Diagnostic
Tester (or equivalent)
GRX3000VAS – Battery
Tester/Charger (or
equivalent)
VAS6154 - Vehicle
Communication
Interface (or equivalent)
Glow Plug Socket
– VAS6454
(or equivalent)
Torque Wrench 1331
5-50Nm - VAG 1331
(or equivalent)
Ring Wrench 7-Piece
Set -3337(or equivalent)
Torque Wrench 1332 40200Nm -VAG 1332
(or equivalent)
Engine Bung Set
-VAS6122(or equivalent)
Diesel Engine Tool Set
- 17mm -T10395A(or equivalent)
Service Modification Validation Web App
This web application is compatible with desktops,
laptops, Apple and Android mobile devices running the
most current versions of FireFox, Chrome, Safari, or
Explorer as well as iOS 9+ on iPads and iPhones.
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen
dealer. 2017 Volkswagen
Group of America, Inc. All Rights Reserved.
November 2017
23V6 Page 6 of 39
NOTE
RISK of Non-payment!
Not using the IN-FORM tool to document and validate
the modification will stop the processing of payment for
your dealership even if the modification has been
completed. Look for the image below to indicate labor
operations, parts, or labeling that requires
IN-FORM tool image documentation.
Emissions Modification Instruction
Section A - Check for Previous Repair
Enter the VIN in Elsa and proceed to the
“Campaign/Action” screen.
TIP
On the date of repair, print this screen and keep a copy
with the repair order.
Confirm the Campaign/Action is open .
If the status is closed, no further work is required.
Note the Applicable Criteria ID for use
in determining the correct work to be done and
corresponding parts associated.
Check for other Open campaign actions .
Other Open campaign actions must be completed
prior to releasing the vehicle to the customer.
Proceed to Section B
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen
dealer. 2017 Volkswagen
Group of America, Inc. All Rights Reserved.
November 2017
23V6 Page 7 of 39
Section B – Check for Service Initiation
NOTE
RISK of Non-payment!
Not using the IN-FORM tool to document and validate
the modification will stop the processing of payment
for your dealership even if the modification has been
completed. Look for the image below to indicate
labor operations, parts, or labeling that requires
IN-FORM tool image documentation.
NOTE
RISK of Non-payment!
Ensure that the “check mark” is present
prior to beginning any repair.
Check the Service Initiation Form for the
presence of the “check mark” .
o
If “check mark” is NOT present,
DO NOT proceed with any repair.
o
If “check mark” is present,
initiate Service Modification
Documentation Form and continue work.
DO NOT proceed with any work unless you can initiate
the Service Modification Documentation Form.
Proceed to Section C
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen
dealer. 2017 Volkswagen
Group of America, Inc. All Rights Reserved.
November 2017
23V6 Page 8 of 39
Section C – Check for Pre-existing MIL ON conditions and Vehicle Modifications
Perform a visual inspection of the intake,
exhaust, and emissions systems.
o If the visual inspection of the intake, exhaust,
or emissions equipment reveals damage or
concerns, STOP, create a VTA ticket and
contact the Volkswagen
Technicians
Helpline.
o If the visual inspection of the intake, exhaust,
or emissions equipment reveals no damage
or concerns, continue the work procedure.
Check for vehicle modifications from original
equipment.
o If vehicle modifications from original
equipment related to emissions components
are found, STOP, create a VTA ticket and
contact the Volkswagen
Technicians
Helpline.
o If vehicle modifications from original
equipment related to emissions components
are not found, continue the work procedure.
Check for illumination of the MIL .
o If MIL is illuminated, STOP, create a VTA
ticket and contact the Volkswagen![]()
Technicians Helpline.
o If MIL is not illuminated, continue the work
procedure.
TIP
VTA cases regarding MIL ON conditions require a GFF
diagnostic log to be uploaded at the time of first contact.
NOTE
RISK of Non-payment!
The purpose for this step is to document vehicle
condition prior to initiation of this action and does
not authorize the repair of any pre-existing
conditions.
Proceed to Section D
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen
dealer. 2017 Volkswagen
Group of America, Inc. All Rights Reserved.
November 2017
23V6 Page 9 of 39
Section D – Refill AdBlue
Lift the rear compartment carpet and slide it
back.
If equipped remove the spare tire by removing
the wing nut .
If equipped remove the foam piece .
WARNING
Protect the hands when prying the plug out of
the tank filler neck.
Sharp-edged body components could cause
injury.
Remove the plug from the AdBlue tank filler neck
.
Open the AdBlue filler cap and fill the tank.
Part Number
G 052 910 A2
Description
AdBlue
Quantity
Up to 19.5L
Proceed to Section E
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen
dealer. 2017 Volkswagen
Group of America, Inc. All Rights Reserved.
November 2017
23V6 Page 10 of 39
Section E – Install Hardware
WARNING
Risk of injury. Refer to “Warning and Safety Precautions”, found in Appendix A at the end of this document.
NOTE
If the vehicle is equipped with air suspension, vehicle lift mode must be activated before raising vehicle with
vehicle jack or hoist so that the air suspension automatic control procedures do not create difficulties.
- Advanced VCI Box, Industry-leading J2534 Pass-Thru...
- High-Speed OEM-Level Diagnostics & Programming: Unlock true...
- Coverage for 17 Car Brands & Ultra Reliability: Works...
- User-Friendly RLink Platform & Expert Support: TOPDON’s...
- 6.6 ft USB-C Cable & Portable Storage Case: The RLink J...
Last update on 2026-06-23 / Affiliate links / Images from Amazon Product Advertising API
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: Emissions Recall
Replacement Service Bulletin Number:
MFR Communication Date: 2017-11-29
MFR Internal Campaign ID/Software Version:
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM)
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- 2026 ALL-IN-ONE HEAVY DUTY TRUCK SCANNER – BUILT FOR DIESEL DIAGNOSTICS:The ANCEL X7HD PRO combines full-system diagnostics, bi-directional control, ECU coding, HDOBD/OBD2 functions, and 42+ reset services in one powerful heavy duty truck scanner. This diesel scan tool helps technicians, fleet owners, and repair shops diagnose problems faster, reduce downtime, and complete more repairs without switching between multiple truck diagnostic tools. Features a 10.1" Android tablet, Bluetooth & Wi-Fi, live data graphing, and 2 years of f-ree updates
- 42+ RESET FUNCTIONS – MORE THAN A BASIC TRUCK CODE READER:Perform essential service functions including forced DPF regeneration, injector coding, speed limiter adjustment, idle adjustment, oil reset, ABS reset, SRS reset, EPB reset, throttle reset, and suspension calibration. Designed for real truck maintenance and fleet service, this commercial truck diagnostic scanner helps reduce dealer visits, avoid unnecessary downtime, and handle more repair jobs with one diesel diagnostic tool
- ACTIVE TEST & ECU CODING – ADVANCED BIDIRECTIONAL SCAN TOOL FOR TRUCKS:Quickly locate faults by activating components and sending commands directly to vehicle systems. Test injectors, ABS, throttle, cooling systems, and other modules in real time without unnecessary disassembly. ECU coding and module matching help adapt replacement parts, restore factory settings, and reduce repeat repairs, making this semi truck scan tool ideal for advanced troubleshooting and daily shop work
- FULL-SYSTEM HDOBD/OBD2 DIAGNOSTICS – WIDE TRUCK & ENGINE COVERAGE:Read and clear codes, monitor live data, freeze frame, and diagnose engine, transmission, ABS, body, and other major systems. Compatible with Freightliner
, Kenworth
, Peterbilt
, Volvo
, Mack
, International
, and other commercial truck brands, plus Cummins
, Caterpillar
, Detroit, Paccar
, and Navistar
diesel engines. Also supports full OBD2/EOBD diagnostics for standard vehicles, making it a versatile truck obd2 scanner for mixed fleets and repair shops - PROFESSIONAL HARDWARE + RELIABLE SUPPORT – BUILT FOR DAILY SHOP USE:This professional diesel diagnostic computer features a 10.1" touchscreen, Android 10.0 system, 6000mAh battery, Bluetooth/Wi-Fi connectivity, and built-in front & rear cameras for documenting repairs and remote troubleshooting. Includes 2 years of fr-ee updates, 1-year w-arranty, and responsive technical support. Contact [email protected] before purchase to confirm compatibility and supported functions for your truck or diesel engine
- 【Built for Heavy Duty Diesel Diagnostics】Designed for SAE J1939 and J1708 compliant trucks, buses, and diesel-powered commercial vehicles. HD601 truck scanner diagnostic tool helps owner-operators, small fleets, mobile technicians, and independent repair shops quickly identify fault codes, view live data, and make informed repair decisions—saving time, reducing downtime, and avoiding unnecessary shop visits
- 【Full System Diagnostics+All HD OBD Modes】The New HD601 heavy duty truck scanner delivers full-system diagnostics on SAE J1939 and J1708-compliant commercial vehicles—digging into engine, transmission, ABS, fuel, every system that keeps your rig rolling. It supports all HD OBD modes, giving you live data, freeze frame, ECU info, vehicle info, emissions data tracking, plus code reading and clearing. Not just what broke, but why—so you fix it right the first time. Pinpoint issues faster, cut repair costs, and spend less time on the shoulder
- 【Wide Heavy-Duty Vehicle Coverage】Supports a wide range of heavy-duty vehicle manufacturers and systems, including Freightliner
, Kenworth
, Peterbilt
, Volvo
, International
, Detroit, Cummins
, Paccar
, Allison, Eaton
, Bendix
, Wabco, and more. Coverage varies by vehicle make, model, year, and system configuration. Contact our support team before purchase if compatibility verification is needed - 【Speaks Major Truck Protocol】The New HD601 diesel truck scanner is built for American-made trucks—and supports the heavy‑duty protocols you' re most likely to run into on the road: SAE J1939, J1708/J1587, ISO 15765‑4, ISO 14230‑4, ISO 9141‑2, J1850 PWM/VPW, ISO 27145‑4, and EURO‑6. For most trucks, model years, and systems, it speaks the language your vehicle understands. Just plug it in and start diagnosing—no guesswork, no gatekeeping. Note: vehicle functions and module availability may vary by manufacturer and model year
- 【Save Hundreds on Diagnostic Fees】Why pay $150–300 for someone to read your codes? With the New ANCEL heavy duty truck scanner, you can pull fault codes yourself—in minutes, without leaving the truck. One or two uses pays for the tool. After that, every diagnostic is money back in your pocket. Smart investment for owner-operators, techs, and small fleets. Read and clear stored fault codes in minutes. Active fault codes may require repairs before they can be cleared
- 【One Tool, Total Fleet Coverage: 6/9/16 Pin Ready】Featuring an integrated 16-pin OBD2 connector and professional-grade 6-pin & 9-pin adapters, this heavy duty truck scanner provides extensive support for J1939, J1708, J1587, ISO 14230-4, ISO 15765-4 and ISO 9141-2, ISO 27145-4 protocols. It offers reliable diagnostic coverage for major American diesel brands—including Cummins
, Paccar
, Caterpillar
, Detroit, and Freightliner
—making it a versatile semi truck scanner for managing any diverse fleet. - 【2 in 1 Diesel Code Reader & Advanced HD OBDII】Equipped with professional-grade diesel scanner capabilities, the HD301 features intuitive Read/Erase codes and turn off the "Check Engine" light. With the built-in DTC Lookup library, you can instantly access fault code definitions on-device without searching the internet. It also retrieves hundreds of essential live sensor data—such as coolant temperature, fuel pressure, and engine RPM—in a stable text format for precise and rapid troubleshooting. (Please note that the HD301 can not support DPF Regen.)
- 【Full System Truck Diagnostic】The FOXWELL HD301 heavy duty scan tool is engineered to deeply access and scan all available electronic control modules specifically for truck, including Engine, Transmission, ABS, SRS, Chassis, and Body Control. This professional truck scanner diagnostic tool allows you to identify issues across the entire vehicle, ensuring your rig stays in peak condition for the long haul.
- 【Versatile for most big Rigs: Commercial, Passenger & Beyond】Engineered for more than just trucks, this heavy duty scan tool offers extensive coverage for pickups, buses, trailers, and even marine vessels. From construction machinery (excavators, loaders) to agricultural equipment (tractors, harvesters), it provides a true all-in-one diagnostic solution.
- 【Plug-and-Play & No Subscription】Designed for the road! No WiFi, no batteries, and no complex App setup required. Simply plug it into your vehicle’s diagnostic port to start scanning immediately. Enjoy lifetime free software updates to keep your HD301 diesel truck scanner current with the latest vehicle models and features—without any hidden subscription fees—While overcoming language barriers with support for Spanish and English.
Last update on 2026-06-23 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.




