NHTSA ID Number: 10133444
Manufacturer Communication Number: Emissions Recall
TSB/Document Date: 2018-04-16
Summary
3.0L TDI vehicles were equipped with undisclosed Auxiliary Emission Control Devices which are not permitted by emissions regulations. Install updated engine control module (ECM) software, transmission control module (TCM) software and hardware to bring affected vehicles into regulatory compliance. Updated resale information included.
Emissions Recall
Code: 23V6
REVISION
Subject
Release Date
Revision Summary
Affected Vehicles
3.0L TDI Engine Emissions System Modification
November 29, 2017
Updated resale information included.
U.S.A.:
2013-2014 MY Volkswagen
Touareg 3.0L TDI Generation 2.1
Check Campaigns/Actions screen in Elsa on the day of repair to verify that a VIN qualifies for repair under this
action. Elsa is the only valid campaign inquiry & verification source.
Campaign status must show “open.”
If Elsa shows other open action(s), inform your customer so that the work can also be completed at
the same time the vehicle is in the workshop for this campaign.
Problem Description
3.0L TDI vehicles were equipped with undisclosed Auxiliary Emission Control Devices which
are not permitted by emissions regulations.
Corrective Action
Install updated engine control module (ECM) software, transmission control module (TCM)
software and hardware to bring affected vehicles into regulatory compliance.
Code Visibility
On or about November 6, 2017, affected vehicles were listed on the Inventory Vehicle Open
Campaign Action report under My Dealership Reports. A list was not posted for dealers who did
not have any affected vehicles. The campaign code showed open on affected vehicles in Elsa
and affected vehicles are identified with this campaign code in the VIN Lookup tool at
www.vw.com.
Owner Notification
Loaner/Rental Vehicle
– REQUIRED!
Owner notification took place on November 6, 2017.
To remain compliant with the Settlement Agreement, Service Consultants must complete a
Loaner/Rental label and it must be signed by the customer. This documents each customer’s
decision to accept or decline the offer for a loaner or rental vehicle while the Approved
Emissions Modification was being performed on their vehicle.
Affix the completed label to the Repair Order and follow the new photo documentation
requirements for this label in the IN-FORM tool.
Emissions Campaigns
Requirements
(CALIFORNIA ONLY)
The California Air Resources Board and the Department of Motor Vehicles (DMV) require
emissions-related campaigns to be completed prior to vehicle registration renewal. When
campaign work is done you must provide the owner with a signed “Vehicle Emission Recall –
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen
dealer. 2017 Volkswagen
Group of America, Inc. All Rights Reserved.
November 2017
23V6 Page 1 of 39
Proof of Correction” certificate (RC EMISCAVWAU). Order certificates online via the
Compliance Label Ordering portal at www.vwhub.com.
Additional Information
Please alert everyone in your dealership about this action, including Sales, Service, Parts
and Accounting personnel. Contact Warranty if you have any questions.
Fill out and affix the appropriate TDI Recall Proof of Completion label and the appropriate
Supplemental Vehicle Emissions Control Information Label after work is complete. Additional
shipments will be released based on the volume of completed repairs claimed through
SAGA. The parts will not be available for order through the website at this time.
The information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These procedures
are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To determine whether
this information applies, contact an authorized Volkswagen
dealer. 2017 Volkswagen
Group of America, Inc. All Rights Reserved.
November 2017
23V6 Page 2 of 39
Claim Entry Instructions
After campaign has been completed, enter claim as soon as possible to help prevent work from being duplicated
elsewhere. Attach the Elsa screen print showing action open on the day of repair to the repair order.
If customer refused campaign work:
U.S. dealers: Submit request via WISE under the Campaigns/Update/Recall Closure option.
Service Number
23V6
Damage Code
0099
Parts Vendor Code
Claim Type
Causal Indicator
Vehicle Wash/Loaner
Criteria I.D.
WWO
Sold vehicle: 7 10
Mark 3.0L Gen 2.1 Kit as causal*
Do not claim vehicle wash/loaner under this action
01
Install 3.0L Gen 2.1 Kit, install Glow Plug with Combustion Chamber Pressure Sensor,
Top off AdBlue tank, and *install a supplemental Vehicle Emissions Control Information
label and TDI Emissions Modification Proof of Completion Label.
Labor operation: 2674 19 99
Quantity
1.00
1.00
Part Number
7P0298099 X
059905061H
Up to 11.00
G 052910A2
155 T.U.
Description
3.0L Gen 2.1 Kit*
Glow Plug with Combustion Chamber Pressure
Sensor
AdBlue (one bottle = 0.5 gallon/ 1.89 Liter)
--AND-Connect battery charger.
Labor operation: 2706 89 50
10 T.U.
--AND-Connect vehicle diagnostic tester, perform software update for control unit.
Labor operation: 2360 22 99
Time stated on diagnostic protocol
(Maximum 60 T.U.)
--AND-Follow IN-FORM tool app.
Labor operation: 0183 00 99
20 T.U.
*Labels are sent free of charge. They cannot be charged to this campaign.
LOANER/RENTAL claiming on next page
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen
dealer. 2017 Volkswagen
Group of America, Inc. All Rights Reserved.
November 2017
23V6 Page 3 of 39
– LOANER/RENTAL MUST BE CLAIMED ON A SEPARATE LINE –
DO NOT PUT ON CAMPAIGN CLAIM
LOANER/RENTAL
Claim Type: A1A
Service #: CU01
Damage Code: 0010
Removed Part : MOB
Outside LO Number : CU010000
DO NOT PUT LOANER/RENTAL ON CAMPAIGN CLAIM
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen
dealer. 2017 Volkswagen
Group of America, Inc. All Rights Reserved.
November 2017
23V6 Page 4 of 39
Campaign Work Procedure
23V6 Emissions Recall
At this time, affected new and used vehicles in dealer inventory are not
included in this emissions modification release.
NOTE
Damages resulting from improper repair or failure to follow these work instructions are the dealer’s responsibility
and are not eligible for reimbursement under this action.
Required Parts
Quantity
1
1
up to 19.5L
Part Description
3.0L Gen 2.1 Kit
Glow Plug with Combustion Chamber Pressure Sensor
AdBlue
Part Number
7P0298099 X
059905061H
Any, as required
IMPORTANT!
AdBlue Ordering Information
Any AdBlue part number in any quantity/volume is acceptable for use.
For claiming purposes, for every 0.5 gallons of AdBlue used, one unit of G 052910A2 should be
entered onto the SAGA claim regardless of which AdBlue part number was used.
Required Labels
Quantity
1
Part Description
TDI Proof of Completion Label
1
VECI Label
1
VECI Label
Part Number
7P0 010 023 B
--AND-059 010 533 BD
--OR-059 010 533 BE
Vehicle
MY 2013 and 2014 Touareg
MY 2013 Touareg
MY 2014 Touareg
IMPORTANT!
Maintaining Your TDI Campaign Label Supply
SAGA claims count! Warranty Administrators should enter TDI claims promptly to ensure
labels can be allocated to support future repairs.
TDI Labels are allocated daily, free of charge, based on the count of TDI claims entered in
SAGA.
TDI labels cannot be ordered through the Compliance Label Ordering Portal. If you have
questions, please email labelrequest@vw
.com.
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen
dealer. 2017 Volkswagen
Group of America, Inc. All Rights Reserved.
November 2017
23V6 Page 5 of 39
Required Tools
VAS6150X - Diagnostic
Tester (or equivalent)
GRX3000VAS – Battery
Tester/Charger (or
equivalent)
VAS6154 - Vehicle
Communication
Interface (or equivalent)
Glow Plug Socket
– VAS6454
(or equivalent)
Torque Wrench 1331
5-50Nm - VAG 1331
(or equivalent)
Ring Wrench 7-Piece
Set -3337(or equivalent)
Torque Wrench 1332 40200Nm -VAG 1332
(or equivalent)
Engine Bung Set
-VAS6122(or equivalent)
Diesel Engine Tool Set
- 17mm -T10395A(or equivalent)
Service Modification Validation Web App
This web application is compatible with desktops,
laptops, Apple and Android mobile devices running the
most current versions of FireFox, Chrome, Safari, or
Explorer as well as iOS 9+ on iPads and iPhones.
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen
dealer. 2017 Volkswagen
Group of America, Inc. All Rights Reserved.
November 2017
23V6 Page 6 of 39
NOTE
RISK of Non-payment!
Not using the IN-FORM tool to document and validate
the modification will stop the processing of payment for
your dealership even if the modification has been
completed. Look for the image below to indicate labor
operations, parts, or labeling that requires
IN-FORM tool image documentation.
Emissions Modification Instruction
Section A - Check for Previous Repair
Enter the VIN in Elsa and proceed to the
“Campaign/Action” screen.
TIP
On the date of repair, print this screen and keep a copy
with the repair order.
Confirm the Campaign/Action is open .
If the status is closed, no further work is required.
Note the Applicable Criteria ID for use
in determining the correct work to be done and
corresponding parts associated.
Check for other Open campaign actions .
Other Open campaign actions must be completed
prior to releasing the vehicle to the customer.
Proceed to Section B
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen
dealer. 2017 Volkswagen
Group of America, Inc. All Rights Reserved.
November 2017
23V6 Page 7 of 39
Section B – Check for Service Initiation
NOTE
RISK of Non-payment!
Not using the IN-FORM tool to document and validate
the modification will stop the processing of payment
for your dealership even if the modification has been
completed. Look for the image below to indicate
labor operations, parts, or labeling that requires
IN-FORM tool image documentation.
NOTE
RISK of Non-payment!
Ensure that the “check mark” is present
prior to beginning any repair.
Check the Service Initiation Form for the
presence of the “check mark” .
o
If “check mark” is NOT present,
DO NOT proceed with any repair.
o
If “check mark” is present,
initiate Service Modification
Documentation Form and continue work.
DO NOT proceed with any work unless you can initiate
the Service Modification Documentation Form.
Proceed to Section C
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen
dealer. 2017 Volkswagen
Group of America, Inc. All Rights Reserved.
November 2017
23V6 Page 8 of 39
Section C – Check for Pre-existing MIL ON conditions and Vehicle Modifications
Perform a visual inspection of the intake,
exhaust, and emissions systems.
o If the visual inspection of the intake, exhaust,
or emissions equipment reveals damage or
concerns, STOP, create a VTA ticket and
contact the Volkswagen
Technicians
Helpline.
o If the visual inspection of the intake, exhaust,
or emissions equipment reveals no damage
or concerns, continue the work procedure.
Check for vehicle modifications from original
equipment.
o If vehicle modifications from original
equipment related to emissions components
are found, STOP, create a VTA ticket and
contact the Volkswagen
Technicians
Helpline.
o If vehicle modifications from original
equipment related to emissions components
are not found, continue the work procedure.
Check for illumination of the MIL .
o If MIL is illuminated, STOP, create a VTA
ticket and contact the Volkswagen![]()
Technicians Helpline.
o If MIL is not illuminated, continue the work
procedure.
TIP
VTA cases regarding MIL ON conditions require a GFF
diagnostic log to be uploaded at the time of first contact.
NOTE
RISK of Non-payment!
The purpose for this step is to document vehicle
condition prior to initiation of this action and does
not authorize the repair of any pre-existing
conditions.
Proceed to Section D
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen
dealer. 2017 Volkswagen
Group of America, Inc. All Rights Reserved.
November 2017
23V6 Page 9 of 39
Section D – Refill AdBlue
Lift the rear compartment carpet and slide it
back.
If equipped remove the spare tire by removing
the wing nut .
If equipped remove the foam piece .
WARNING
Protect the hands when prying the plug out of
the tank filler neck.
Sharp-edged body components could cause
injury.
Remove the plug from the AdBlue tank filler neck
.
Open the AdBlue filler cap and fill the tank.
Part Number
G 052 910 A2
Description
AdBlue
Quantity
Up to 19.5L
Proceed to Section E
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen
dealer. 2017 Volkswagen
Group of America, Inc. All Rights Reserved.
November 2017
23V6 Page 10 of 39
Section E – Install Hardware
WARNING
Risk of injury. Refer to “Warning and Safety Precautions”, found in Appendix A at the end of this document.
NOTE
If the vehicle is equipped with air suspension, vehicle lift mode must be activated before raising vehicle with
vehicle jack or hoist so that the air suspension automatic control procedures do not create difficulties.
- Advanced VCI Box, Industry-leading J2534 Pass-Thru...
- High-Speed OEM-Level Diagnostics & Programming: Unlock true...
- Coverage for 17 Car Brands & Ultra Reliability: Works...
- User-Friendly RLink Platform & Expert Support: TOPDON’s...
- 6.6 ft USB-C Cable & Portable Storage Case: The RLink J...
Last update on 2026-06-23 / Affiliate links / Images from Amazon Product Advertising API
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: Emissions Recall
Replacement Service Bulletin Number:
MFR Communication Date: 2017-11-29
MFR Internal Campaign ID/Software Version:
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM)
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- 🎉[OTOFIX D1 Lite, Perfect Cost-effective Diagnostic Tool]: OTOFIX D1 Lite, a newest bidirectional scan tool from OTOFIX company, is a great choice for DIYers and repair shops. 👉This obd2 scanner diagnostic tool packs all practical functions: OE level all systems diagnoses, Bi-Directional Control, 38+ reset services fixing 99% of common problems, support DoIP & CANDF protocols and FCA
AutoAuth, high-end hardware configuration. Worldwide vehicles and 🔥2 Years Free Updating🔥 covered. - 🎉[Bi-Directional Scan Tool, Active Test]: OTOFIX D1 Lite bluetooth obd2 scanner can also command ECUs and monitor the operation of the actuators to track down the problems of certain parts, like windows, sunroof, wipers, fuel pumps, etc., saving repair time & trouble. This makes OTOFIX D1 Lite the most cost-effective bidirectional scan tool.
- 🎉[2026 Newest, 38+ Hot Reset Functions]: Equipped with 38+ reset functions in one, the OTOFIX D1 lite automotive scanner diagnostic tool allows you to troubleshoot 99% of common vehicle problems. You can use this car diagnostic scanner holding enough functions to easily repair common vehicle models in your repair shops. Including Oil Reset, Injector Coding, Throttle, DPF Reset, SCR Reset, Gear Learning, Clutch Learning, Suspension, etc. Note* Reset functions vary by model.
- 🎉[OE Level Full Systems Diagnostics]: Unlike the 2-system and 4-system diagnostic tools, the OTOFIX auto scan tool can complete comprehensive system diagnostics within 5 minutes. It accesses and scans all available onboard systems like for Engine /AT /ABS /EPB /BMS /TPMS /SRS /SAS /Audio System /BCM /Air Conditioning / etc., to read & clear codes, view live data, and check ECU information. Note: Active test is not involved.
- 🎉[Powerful Hardware Configuration]: Designed with a fashion appearance & a 7” touchscreen and a weight of 463g, this OTOFIX D1 Lite OBD2 diagnostic scanner scan tool is convenient for everywhere and easy to use & store. Android9.0 OS and 2+64GB memory enhance multi-task smoothness and diagnostic operation, no more wasting too much time. 5800mAh battery allows hours-lasting use. WiFi & VCI1 also bring faster communication for your diagnostics.
- 🏆【2026 TOP OBD2 Scanner Diagnostic Tool】OTOFIX D1 Lite wireless obd2 scanner has upgraded hardware configuration and car coverage. The newly upgraded D1 Lite with 🔥OS Android 9.0🔥1.5Ghz 4 core high efficiency processor🔥2GB RAM
+64GB ROM large storage🔥5800mAh large battery, more stable and longer lasting diagnostics🔥 38+ Reset🔥action tests🔥full system diagnostic🔥Supports MV105 endoscope🔥21+ Language Supports🔥100000+ vehicle coverage to meet all your daily maintenance needs. - 👍【Bi-Directional Control / Active Test】D1 Lite obd2 scanner has bidirectional control(worth $300+), which is the most beloved feature among mechanic. If your headlights or car windows are broken, going to a repair shop will cost a lot of money. You can use D1 Lite to send execution commands to the ECU module and identify the repair status. Such as ABS, car windows, doors, valves, wipers, headlights, etc., effectively shorten diagnostic time and reduce diagnostic costs.
- 🔥【All Systems Diagnostics, In-depth Checking】This advanced OBD2 Scanner D1 Lite can perform OE-level diagnosis of all systems including engine, transmission, airbag, ABS, ESP, TPMS, gateway, steering, radio, and air conditioning for more than 100 brands. This diagnostic scanner supports essential functions, such as reading ECU version info, reading and clearing fault codes, and reading data streams.With just a simple click, it provides you with accurate and in-depth diagnostics.
- 🏆【38+ Reset Hot Functions】For repair workshops, holding an OTOFIX D1 Lite Auto scanner is a strong advantage over others. Its 38+ maintenance functions provide various solutions for all module repairs, including Oil Reset, TPMS Reset, Injector Coding, Suspension, Throttle Matching, etc., which will usher your repair business to a new pinnacle. Continuously updating will never make the functionality & compatibility out-of-date.
- 🏆【150+ Models, 10000+ Car Coverage & 16 Languages】D1 Lite is a comprehensive car diagnostic scan tool, help you to troubleshoot car issues fast for 95% US, European, Asian auto makes. ✅ With frequent updates and optimizations allow D1 Lite to cover more vehicles to meet your needs. ✅ Multilingual menu allows auto mechanics around the world to use it without language barriers. 🚩Note: Kindly send us the S/N of the device to authorize new language updates before changing the menu language.
- 2026 Newest Wireless Bluetooth Scan Tool D1: OTOFIX D1 Diagnostic scanner is upgraded version with Enhanced Hardwares & Newest Functions, FASTER and SMARTER! ✅Alternative Bluetooth 5.0 +USB connect✅2G+64GB✅Android 9.0 OS✅5G & 2.4 GHz Dual WiFi✅5800mAh battery👍VAG Guided Function👍ECU Online Coding👍CANFD&DOIP👍40+ Services👍Bi-Directional Control👍Full Systems Diagnose👍2 Years Free Update👍150+ Vehicle Coverage🎁Contact to get gift: otofixaftersales-amz@ outlook.com
- ECU Coding to Unlock the Hidden Features: OTOFIX D1 obd2 scanner diagnostic tool newly adds ECU Coding which can Online Coding(ONLY for VW
/Au.di/Sk0da), Variant Coding/Offline Programming, Flash Hidden Functions, Reset Adaptive Data, Match Replaced Components, Customize OE-Settings. Such as: halogen fog lamps retrofitted with xenon fog lamps, different capacity battery retrofit, disbale auto start-stop, sunroof initialization, injector calibration, etc. PS: Coding functions vary by model&year. - Full Bidirectional Control for Active Car Tests: The D1 OTOFIX scanner also offers bi-directional control, allowing you to perform powerful active tests on car subsystems. This means that you can check the working status and functionality of open & close solenoids, energize injectors, turn cooling fan on & off, and more, all from the device itself.🚩The D1 bi-directional obd2 scanner can quickly help you to check if a system or component goes well,Improving 200% Efficiency.**Note that Active Tests available depend on the make/model/year of your car.
- 40+ Popular Maintenance Functions: OTOFIX D1 obd scanner for car performs 40+ hot services, including Oil Reset, EPB, TPMS, BMS, E.GR, G.PF, D.PF, SAS Calibration, ABS Bleeding, Injector Coding, Gearbox Match, Suspension, Crankshaft Relearn, Power Balance, etc., still growing. Great choice for DIYers, technician, repair shop. 🚩Get MORE special functions from "Car Brand>System>Service". Check compatibility before purchase via 📧 otofixaftersales-amz@ outlook.com.
- OE-Level All Systems Diagnostic + One-Click AutoVIN & AutoSCAN: OTOFIX D1 scanner automotriz gives you the ability to troubleshoot entire car systems including engion system,transmission system,body system,chassis,etc. 🚩One of the standout features of the D1 obd2 scanner diagnostic tool is the one-click AutoVIN & AutoScan function. This feature allows you to quickly and easily scan all diagnosable ECUs with just one click, and identify any problems hidden in your vehicle's systems.
Last update on 2026-06-23 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.




