•

Select “Attach to the test plan” .

The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen dealer. 2017 Audi of America, Inc. All Rights Reserved.
November 2017

23V5 Page 26 of 36

NOTE
RISK of Scan Tool Damage!
•

Do not leave the scan tool on the windshield during
the flash process, as it is possible that the
windshield wipers may cycle.
•

From the Test plan screen, Select “SVM Code
input” test plan , then select “Perform
test” .

•

Follow the on-screen prompts.

•

Enter the corrective action code (SVM code)
as listed below.

SVM code

23V5A660
•

Select “Accept”, and follow the on-screen prompts
to complete the flash.

NOTE
•

It is IMPERATIVE that ALL of the ignition
cycle on/off delay requests are fulfilled in their
entirety during this flash process .

•

Failing to wait for the ignition on/off timing
cycle to complete (progress bar and
countdown timer ) before cycling the
ignition on/off MAY damage a control module.

•

Damage to control modules as a result of
failing to wait the specified time displayed by
the progress bar and countdown timer
are NOT covered under this action.

The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen dealer. 2017 Audi of America, Inc. All Rights Reserved.
November 2017

23V5 Page 27 of 36

•

At the end of the diagnostic session, Select “Send”
and follow the prompt for sending the log
on-line.
NOTE

RISK of Non-payment!
Diagnosis logs must be sent on-line after the flash
process to be considered for reimbursement.
TIP
Technicians may find it helpful to also store the log on
a USB stick for back-up.

Proceed to Section F.

The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen dealer. 2017 Audi of America, Inc. All Rights Reserved.
November 2017

23V5 Page 28 of 36

Section F – Supplemental Vehicle Emissions Control Information Label
Install Supplemental Vehicle Emissions Control
Information Label

TIP
•

The surface where the label is to be installed
must be clean, dry, and free from oil residue
prior to installing the label.

•

Label must NOT cover any existing label(s).

•

Label must be installed in location shown.

•

Photo documentation of label installed is
required.

The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen dealer. 2017 Audi of America, Inc. All Rights Reserved.
November 2017

23V5 Page 29 of 36

•

Open the hood.

•

Clean the surface where the label is to be
installed .

•

Install the Supplemental Vehicle Emissions
Control Information (VECI) label according to the
chart below on the underside of the hood or onto
the core support. The Supplemental Vehicle
Emissions Control Information (VECI) label and
TDI Recall Proof of Completion label should be
placed next to each other so that a single
photograph can capture both labels.
Vehicle

Label part number

MY 2013

059 010 533 BH

MY 2014

059 010 533 BJ

MY 2015

059 010 533 BK

NOTE
DO NOT Cover ANY existing labels!

Proceed to Section G

The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen dealer. 2017 Audi of America, Inc. All Rights Reserved.
November 2017

23V5 Page 30 of 36

Section G – TDI Recall Proof of Completion Label
Install TDI Recall Proof of Completion label
TIP
•

The surface where the label is to be installed
must be clean, dry, and free from oil residue
prior to installing the label.

•

Label must NOT cover any existing label(s).

•

Photo documentation of label installed is
required.

•

Clean the surface next to the Vehicle Emission
Control Information Label where the TDI Recall
Proof of Completion label is to be installed.

•

Fill out completely the Recall Code, Dealer Code,
and Repair Date.

•

Affix the TDI Recall Proof of Completion label and
verify that the correct part number is being
installed according to chart below onto the
underside of the hood or onto the core support.
The TDI Recall Proof of Completion label and
Supplemental Vehicle Emissions Control
Information (VECI) label should be placed next to
each other so that a single photograph can
capture both labels.
Vehicle

Label part number

MY 2013 - 2014

4L0 010 023 B

MY 2015

4L0 010 023 A

NOTE
DO NOT Cover ANY existing labels!
•

Apply clear overlay (provided)

•

Close the hood

Proceed to Section H

The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen dealer. 2017 Audi of America, Inc. All Rights Reserved.
November 2017

23V5 Page 31 of 36

Section H – Service Modification Documentation Requirements
Job Roles Summary:
•

Service Consultant – Initiates validation tool.

•

Service Technician –
modification requirements.

•

Manager – Validates the modification was properly
completed.

•

Dealer Representative/Cashier – Prints receipt,
fuel economy label and delivers to customer.

•

Warranty Administrator – Enters claim into the
SAGA system.

Completes

service

TIP
To access the interactive forms go to the TDI Settlement
Program microsite on vwhub.com. Then Select the “TDI
IN-FORM” Button from the lower left side of the microsite
navigation.
•

Enter the “TDI IN-FORM” tool

•

Enter the VIN for the vehicle that requires
documentation.

TIP
The VIN can be manually typed in or using an iPad or
iPhone running i0S 9+, the camera can be used to scan
the VIN Barcode.
Please note ambient lighting, camera quality, etc. may
impact the effectiveness of the VIN scanning feature.

The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen dealer. 2017 Audi of America, Inc. All Rights Reserved.
November 2017

23V5 Page 32 of 36

TIP
After the VIN has been entered, the system will
automatically validate that it is a TDI VIN. This will be
indicated by a green check mark that will appear next to
the VIN.
•

Validate the VIN is correct for the vehicle, then click
the “Submit” button .

•

Select “Service Modification Documentation Form”
.

•

Follow the on-screen prompts completely.
NOTE

RISK of Non-payment!
Not using the IN-FORM tool to document and validate
the modification will stop the processing of payment for
your dealership even if the modification has been
completed.
TIP
Upon completion of the Service Modification
Documentation Form, the Manager must validate the
repair in the IN-FORM tool.

Proceed to Section I

The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen dealer. 2017 Audi of America, Inc. All Rights Reserved.
November 2017

23V5 Page 33 of 36

Section I – Campaign Stamp
•

Once the campaign has been completed, the
technician should stamp the repair order.

•

Stamps are available for ordering through the
Compliance Label Ordering Portal (item#
AUD4927ENG or AUD4927FRE).

Proceed to Section J
Item#: AUD4927ENG
OR

Item # AUD4927FRE

Section J – Parts Return
Parts Return/Disposal
SCR Catalyst:
•

The SCR Catalyst must be tagged with a blue zip
tie and returned in order to be
considered for core charge reimbursement.

All other parts:
•

Properly store (retain), destroy or dispose of
removed parts in accordance with all state and
local requirements, unless otherwise indicated
and/or requested through the Warranty Parts
Portal (WPP).

All Work Complete
Proceed to Section K for California Only

The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen dealer. 2017 Audi of America, Inc. All Rights Reserved.
November 2017

23V5 Page 34 of 36

Section K – California Only Requirements
CALIFORNIA ONLY Requirements for Emissions Campaigns Having Customer Notification
The California Air Resources Board and the Department of Motor Vehicles (DMV) require emissions-related
campaigns to be completed prior to vehicle registration renewal. When campaign work is done you must provide
the owner with a signed “Vehicle Emission Recall – Proof of Correction” certificate (RC EMIS_CAL VW).
Certificates can be ordered at no cost online via the Compliance Label Ordering portal at www.accessaudi.com.

TIP
Ensure owners are aware of the importance of retaining the completed certificate for their records. It should be
mailed to the California DMV only upon request.

Appendix A – Warnings and Safety Precautions
WARNING
Note the following when working on the whole exhaust system:
•

Danger of eye injury, wear protective eyewear

•

Wear gloves (for example rubber gloves, not cloth gloves) and protective eyewear to prevent any harmful
contact with the skin and eyes - risk of injury.

•

Do not remove the exhaust gas temperature sensor - risk of injury.

WARNING
The reducing agent can cause skin irritation.
•

To prevent large amounts of reducing agent from leaking out when opening the metering line, wait for the
recirculation process to be completed.

•

Avoid contact with skin and eyes! Wear protective gloves!

•

If reducing agent should get on your skin, wash it off immediately with soap and water.

•

If reducing agent gets in your eye, rinse the eye for several minutes with water.

•

Never inhale or swallow the reducing agent!

•

Should you swallow any reducing agent, rinse your mouth, drink plenty of water and contact a doctor
immediately.

The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen dealer. 2017 Audi of America, Inc. All Rights Reserved.
November 2017

23V5 Page 35 of 36

Appendix B – 3.0L Gen 2.1 Parts Kit
Kit

4L0 298 099 X
Gen 2.1 Kit

Part Number
7P0 254 400 BX
7L5 253 115 C
1K0 253 141 J
N 91130802
N 01024713
4H0 131 113 A
3C0 253 725
059 906 261

Part Description
Exhaust Pipe With Catalyst And Adapters
Gasket
Dual Clamp
Shouldered Hex Nut
Replacement Stud/Bolt
Injector For Reduction Agent
Retaining Clamp
PM Sensor

Quantity
1
1
1
3
3
1
1
1

Diagram
Location
1
5
2
4
6
7
9
3 / 11

The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen dealer. 2017 Audi of America, Inc. All Rights Reserved.
November 2017

23V5 Page 36 of 36