Instruction Sheet

IS-17907

VOLVO ELECTRONIC LOGGING DEVICE (ELD) INSTALLATION

MATERIAL
For Pre-Multiplex vehicles*, use one of the following kits:
Part No.

Description

Qty

7770381

Volvo ELD, US/CAN cross border kit

1

7770382

Volvo ELD, Canada only kit

1

For Multiplex vehicles*, use one of the following kits:
Part No.

Description

Qty

7770385

Volvo ELD, US/CAN cross border kit

1

7770388

Volvo ELD, Canada only kit

1

*Multiplex vehicles 2005+ H Series vehicles (VIN 5-0168 and up)
Multiplex vehicles 2007+ X Series vehicles (VIN 7-8932 and up)

Other parts that may be required:
Part No.

Description

Qty

069800

ELD Interface kit for OBD vehicles

1

069799

ELD Interface kit for US07 & US10 vehicles using Volvo D13 Engine

1

069798

ELD Interface kit for vehicles equipped with Detroit Diesel engine

1

NOTE
Material can be obtained through regular channels.

Writer: MG

IS-17907
Page 2 / 4

DANGER
Park vehicle safely, apply parking brake, stop engine. Prior to working on the vehicle, set the ignition
switch to the OFF position and trip the main circuit breakers equipped with a trip button.
Do not attempt to install, re-configure or remove any product from a vehicle while the vehicle is in
motion or otherwise in operation. All installation, configuration or removal must be done only in
stationary vehicles which are securely parked. Attempting to service devices while the vehicle is in
motion could result in malfunctions or accidents, leading to death or serious personal injury
Read and follow all instructions and warnings to prevent serious injury and/or vehicle damage.

DANGER
All in-vehicle devices and related cabling must be securely fastened and kept clear of all vehicle
controls, including gas, brake and clutch pedals.
This requires the use of a cable tie when securing the device or any extension harness to the
connector, securing both sides of the harness.
If you do not use a cable tie, vibration in the vehicle can lead to a loose connection which could
indirectly cause the vehicle’s engine computer to fail, loss of vehicle control and cause serious injury.
Inspect devices and cabling regularly to ensure all devices and cabling continue to be securely
attached.

DANGER
If at any point after an in-vehicle device is installed a warning light illuminates on the vehicle dash or
the vehicle stalls or has a marked drop in performance, shut off the engine, remove the device, and
contact your Prevost representative. Continuing to operate a vehicle with these symptoms can cause
loss of vehicle control, and serious injury.

DANGER
Your in-vehicle devices must be kept clear of debris, water and other environmental contaminants.
Failure to do so may result in units malfunctioning or short-circuiting, that can lead to a fire hazard and
cause loss or serious injury.

DANGER
Do not attempt to remove the devices from the vehicle in which they are originally installed for
installation in another vehicle. Not all vehicles share compatibility, and doing so may result in
unexpected interactions with your vehicle, including sudden loss of power or shutdown of the vehicle’s
engine while in operation or cause your vehicle to operate poorly or erratically and cause serious injury
and/or vehicle damage.

Writer: MG

IS-17907
Page 3 / 4

PROCEDURE

PREPARING FOR INSTALLATION
Before installing your device, please document your device serial number. You will need this
information at a later time to verify your installation.
Ensure no dash warning lights are on in the vehicle while it is running, and all other functions such as
headlamps and flashers etc. are working prior to installing the device.

INSTALLING THE ELD
1. Connect the Volvo ELD to the supplied
harness (square 16 Pins connector). Make
sure the device is fully inserted to allow good
connection.
2. If kit #7770381 or 7770382 are used (PreMultiplex) connect the round 6 Pins connector
directly to the vehicle diagnostic port and lock
in place by turning the lock ring firmly
clockwise until an audible “click” is heard (a
spare diagnostic port is supplied as part of
the harness to allow future diagnostic
procedure without removing/disconnecting
the Volvo ELD).
If kit #7770385 or 7770388 are used
(Multiplex), connect the round 9 Pins
connector to the vehicle ELD connector
located at knee level under the left dashboard
area. Lock in place by turning the lock ring
firmly clockwise until an audible “click” is
heard.

ELD 16 PINS SQUARE CONNECTOR

6 PINS CONNECTOR (PRE-MULTIPLEX)

CAUTION
Please take note that for vehicles using a
Multiplex system, the OBD connector is only
intended for diagnostic equipment connection
and must remain unconnected at all times
except during vehicle maintenance. Installing
an aftermarket plug-in device that uses the
OBD port in these vehicles may cause
interference and/or damage to the vehicle
systems, potentially affecting operating safety.

Writer: MG

9 PIN CONNECTOR (MULTIPLEX)

IS-17907
Page 4 / 4

NOTE
When correctly connected, 6 quick beeps
will be heard and all three LEDs on the
device will flash briefly.
DO NOT USE SQUARE OBD CONNECTOR

3. Park the vehicle outside to ease satellite
localisation and let the vehicle run for
approximately 3 minutes.
During this time period, the red LED will
illuminate on the face of the device. Shortly
afterward, the green and blue LEDs will also
illuminate when the device connects to the
cellular and GPS networks. This initial startup
period may take several minutes to complete.
4. Once all three LEDs have come on, secure
your device using supplied cable ties.

ELD FRONT LEDS

INSTALLATION VERIFICATION
To check the status of the device you have installed, navigate to installmygps.com. On the
web page, fill in your name, the company, and the device serial number, which can be found
on the bottom of the device. Once complete, click Log Install.
You will now see a similar screen with green text to indicate that your installation was
successfully completed. If you see red text instead, you must check the installation
For the latest version of the Limitations of Use, please visit: goo.gl/k6Fp0w.

Writer: MG