IK0800223 - Accelerator Position Sensor/Idle Validation Switch APS / IVS Diagnostics ...

Page 1 of 4

Countries:

CANADA, UNITED STATES, Document
MEXICO
ID:

IK0800223

Availability:

ISIS, Bus ISIS, FleetISIS,
Body Builder

Revision:

5

Major System: ELECTRICAL SYSTEM

Created:

2/24/2010

Current
Language:

English

Last
Modified:

10/23/2013

Other
Languages:

Français, Español,

Author:

Joe
Christopher

Viewed:

10672
Less Info

Coding Information

Hide Details

Copy Relative
Link

Copy Link

Bookmark

Add to Favorites

View My
Bookmarks

Print

Provide
Feedback

Helpful

Not Helpful

1779

2239

Title: Accelerator Position Sensor/Idle Validation Switch APS / IVS Diagnostics DLCII
equipped engine control systems
Applies To: All DLCII equipped engines 2003-2006 including VT275. VT365, DT466E and
570E engine. Vehicles included, but not limited to: CF500 and 600, Workhorse™ brand
chassis'. 4200,4300,4400,7400,7500, 8500, CE Bus, RE Bus, FE Bus, 1552 and 1652 SC,
DESCRIPTION

Two new APS sensors (Accelerator Position Sensor) have been developed and released for use with pre-2010
emissions International Engines. The new sensors listed below contain "non-contact" hall-effect idle validation
sensors. This replaces the open/closed IVS switches in the old sensors . As a result of this new design, the
normal resistance measurements performed for the potentiometer and idle validation switch on the previous
"contact' sensor are no longer applicable. A technician can continue to perform resistance measurement tests on
the engine harness with the sensor unplugged (open circuit), but should rely solely upon the voltage
measurement tests, with a breakout harness installed, at the ECM and APS sensor, and the new
sensor connected.
SYMPTOMS





APS/ IVS fault codes present
Engine speed restricted to idle
Erratic automatic transmission operation
Engine warning lights illuminated

POSSIBLE DIAGNOSTIC TROUBLE CODES
VT275, VT365, DT466/570 EGR 2004-2007 engines

DTC MODULE

DESCRIPTION

131

ECM

APS signal voltage out-of-range LOW . < 0.147 V for more than 0.35 seconds.

132

ECM

APS signal voltage out-of-range HIGH. > 4.55 V for more than 0.35 seconds.

133

ECM

APS signal in-range fault.

134

ECM

APS and IVS disagree.

135

ECM

Idle validation switch circuit fault

PARTS INFORMATION
Please refer to TSI letter 10-08-01 for parts details including cross reference information. Follow link: TSI letter 10-08-01

https://evalue.internationaldelivers.com/service_kb/DocTool/ArticleViewer.aspx?ControlI...

11/1/2013

IK0800223 - Accelerator Position Sensor/Idle Validation Switch APS / IVS Diagnostics ...

Page 2 of 4

DIAGNOSTICS
There can be various conditions that can cause APS/IVS related issues. As with any performance related fault, a thorough
description of the issue, from the operator is critical.







Is the fault sensitive to road conditions, such as rough terrain, hills, etc ?
Is the fault temperature sensitive ?
Does the fault occur, when coming to a stop, or when accelerating or cruising ?
Do any other faults occur at the same time, such as loss of dash cluster, or other in cab accessories ?
Is there other codes, that can be attributed to this issue?
Are there faults regarding the IAT (intake air temperature) sensor, BAP(barometric air pressure sensor)?

If any circuit issues are suspected, a thorough visual inspection of all circuitry for shorts, and opens is critical, as intermittent issues
are usually caused by wiring faults. Any harness mounting points should be disassembled and inspected. Where harnesses pass by
sharp edges, or possible points of abrasion should be inspected and if required, repaired.
Whenever connector inspection has been performed, and tested satisfactory, always apply a light coating of dielectric grease upon
reconnection, being careful to properly lock connectors.
If idle validation faults are an issue, testing of the ignition voltage supply to the sensor should be performed.
COMPONENT FUNCTION/DESCRIPTION

When the ignition is ON, the ECM continuously monitors the APS/IVS circuits for expected voltages. The ECM
also compares the APS and IVS signals for differences. If the signals are not what the ECM expects to see, the
ECM sets Diagnostic Trouble Codes.
APS
The ECM supplies a regulated 5 V signal from ECM chassis connector Pin X4-4 to APS connector Pin C. The
APS returns a variable voltage signal (depending on pedal position) from the APS connector Pin A to ECM Pin
X4-18. The APS is grounded at Pin B from the ECM Pin X4-24.
APS Auto-Calibration
The ECM learns the lowest and highest pedal positions by reading and storing the minimum and maximum voltage levels from the
APS. In this manner the ECM auto-calibrates the system to allow maximum pedal sensitivity. The ECM auto-calibrates as the ignition
switch is on, but when the ignition switch is turned OFF, these values are lost. When the key is turned on again, this process starts
over. When the pedal is disconnected (or a new one is installed), the pedal does not need to be calibrated. It simply auto-calibrates
the new pedal assembly whenever the key is turned on again.
IVS
The ECM expects to receive one of two signals through the ECM chassis connector Pin X4-12 from APS/IVS connector Pin D:
• 0 V when the pedal is at the idle position.
• B+ when the pedal is depressed
The IVS receives a 12 V ignition voltage at Pin F from the ignition fuse in the power distribution box. When the pedal is not in the idle
position (throttle applied), the IVS supplies a 12 V signal to the ECM.
The ECM compares APS/IVS inputs to verify when the pedal is in the idle position. If the APS signal at Pin X4-18 indicates throttle is
being applied, the ECM expects to see 12 V at the IVS. If the APS signal indicates throttle is not applied, the ECM expects to see 0 V
at the IVS. The timing process is critical between the APS and IVS sensors. For this reason, it is very difficult to determine if the
APS/IVS assembly is working correctly when using a Digital Multimeter (DMM).
Fault Detection / Management
When the key is on, the ECM continuously monitors the APS/IVS circuits for expected voltages. It also compares the APS and IVS
signals for conflict. If the signals are not what the ECM expects to see, Diagnostic Trouble Codes (DTCs) will be set.
Any detected malfunction of the APS/IVS sensor circuit will illuminate the amber ENGINE lamp. If the ECM detects an APS signal
Out of Range HIGH or LOW, the engine will ignore the APS signal and operate at low idle. If a disagreement in the state of IVS and
APS is detected by the ECM and the ECM determines that it is an IVS fault, the ECM will only allow a maximum of 50% APS to be
commanded. If the ECM cannot discern if it is an APS or IVS fault, the engine will be allowed to operate at low idle only. .
TROUBLESHOOTING

NOTE:
When performing diagnostic tests, be sure to refer to the correct circuit diagram manuals, found on ISIS, for the vehicle you are
working on.

https://evalue.internationaldelivers.com/service_kb/DocTool/ArticleViewer.aspx?ControlI...

11/1/2013

IK0800223 - Accelerator Position Sensor/Idle Validation Switch APS / IVS Diagnostics ...

Page 3 of 4

ZTSE 4486 - APS /IVS Breakout Tee

General Circuit Diagram DLCII
Connector Voltage Checks
(Check with Sensor Connector disconnected, and Ignition Key On)
Test Points
Specification
Comments
If greater than 0.25V, signal is shorted to VREF or B+.
A to GND
< 0.25V
B to GND
C to GND

0V
5 ± 0.5V

D to GND

< 0.25V

F to GND

12V ± 1.5V

Signal ground no voltage expected.
Voltage > spec, wire shorted to B+
Voltage > 0.25V, IVS signal wire shorted to VREF or B+
Voltage < 10.5V check circuit for open or resistance.

Harness Resistance Checks
(Install breakout box on chassis harness only. Connect ZTSE-4485 - APS/ IVS Break Out Tee to chassis harness
only.)
Test Points

Specification

Comments

X4-18 to A

< 5 ohm

If > 5 ohm, check for APS signal wire open.

X4-24 to B

< 5 ohm

If > 5 ohm, signal ground open.

https://evalue.internationaldelivers.com/service_kb/DocTool/ArticleViewer.aspx?ControlI...

11/1/2013

IK0800223 - Accelerator Position Sensor/Idle Validation Switch APS / IVS Diagnostics ...

X4-4 to C

< 5 ohm

If > 5 ohm, VREF wire open.

X4-12 to D

< 5 ohm

If > 5 ohm, IVS signal wire open.

Fuse to F

< 5 ohm

If > 5 ohm, IVS power wire open.

Page 4 of 4

Operation Voltage Checks for APS/IVS Sensor with breakout box
(Check with breakout box installed [X4 only] to ECM and Chassis harness. Inspect for bent pins or corrosion.)
APS Test Points
(+) X4-18 to (-) X4-24
Position

Voltage

IVS Test Points
(+) X4-12 to (-) X4-24

% APS

Voltage

Low Idle

0.64V to 0.66V

0%

0V

High Idle

3.84V to 3.86V

98% to 102%

B+

Comments
IVS toggles just off idle

NOTE:

If any of the circuit readings are not within the required specifications, keep in mind, that the IAT (Intake Air
Temp.) sensor, is spliced with the signal ground and BAP (Barometric Air Press.) sensor circuits are spliced with
the 5 volt reference circuits, of the APS/IVS. These circuits should also be inspected, as they can affect the
APS/IVS function/readings.
NOTE:
If all circuit and operational tests have been performed, and all wiring/components have been inspected and are deemed to
be satisfactory, yet the issue is still unresolved, open a tech service case file for further diagnostic assistance.

ADDITIONAL RELATED IKNOW DOCUMENTS:

IK0800218 Accelerator Position Sensor/Idle Validation Switch APS /IVS Diagnostics, 3-Box equipped engine control systems
IK0800219 DLC equipped vehicles Accelerator Position Sensor/IdleValidation Switch APS / IVS Diagnostics NavPak™, CEC
equipped engine control systems
IK0800226 Accelerator Position Sensor/ Idle Validation Switch APS / IVS Diagnostics, MaxxForce® equipped engine control
systems
IK0800227 Accelerator Position Sensor / Idle Validation Switch APS / IVS Diagnostics MaxxForce® 11 and 13

engines
Hide Details

Feedback Information
Viewed:

10671

Helpful:

1779

Not Helpful: 2239
No Feedback Found

Copyright © 2013 Navistar, Inc.

https://evalue.internationaldelivers.com/service_kb/DocTool/ArticleViewer.aspx?ControlI...

11/1/2013