IK1200598 ­ Chassis Mounted Oil Centrifuge Filter Diagnostics (Air & Oil Leaks)

Page 1 of 6

CANADA, UNITED
STATES, PUERTO
RICO

Document
IK1200598
ID:

Availability:
Major
System:
Current
Language:
Other
Languages:

ISIS, FleetISIS

Revision:

5

ENGINES

Created:

4/27/2011

English

Last
Modified:

2/17/2014

Français, Español,

Author:

Jay
Weston

Viewed:

7249

Countries:

Less Info
Coding Information

Hide Details

Copy Link

Copy Relative
Link

Bookmark

Add to
Favorites

Print

Provide
Feedback

View My
Bookmarks

Helpful

Not Helpful

589

459

Title : Chassis Mounted Oil Centrifuge Filter Diagnostics (Air & Oil Leaks)
Applies To : EPA10 MaxxForce 11, 13, and 15 Engines

DESCRIPTION
Centrifuge Filter Trouble-Shooting and Parts Lists. Many of the components on the chassis
mounted soot centrifuge are serviceable to alleviate the need to replace the entire assembly.

SYMPTOMS
• Excessive Noise
• Air Leak or Air System Leaking Down
• Oil Leaks
PARTS INFORMATION

(Exploded View)

https://evalue.internationaldelivers.com/service_kb/DocTool/ArticleViewer.aspx?ControlID... 3/5/2014

IK1200598 ­ Chassis Mounted Oil Centrifuge Filter Diagnostics (Air & Oil Leaks)

Page 2 of 6

Item
Number

Part
Number

1

3013406C2 Cover Assembly, Centrifuge

1

2

3013407C1 Clamp, Centrifuge Oil Filter

1

3
4

3013376C1 Seal, Centrifuge Assy
2598201C1 Seal, O-Ring

1
1

Description

Quanity

https://evalue.internationaldelivers.com/service_kb/DocTool/ArticleViewer.aspx?ControlID... 3/5/2014

IK1200598 ­ Chassis Mounted Oil Centrifuge Filter Diagnostics (Air & Oil Leaks)

Page 3 of 6

5

3013570C1 Valve, Check

1

6

2598202C1 Screw, Set Hex Head

4

NOTE: The following parts are Non-Illustrated
2610033C1 Valve Assy, Air
2601156C1 Bearing, Cone Inner
2610158C1 Seal Idle Cut Out Valve

1
1
1

2610323C1 Kit, Lower Bearing, Filter Body
3013473C1 Kit, Anti-Vibration Mount

• 3014297C92 Kit, Cover Assembly includes Cover (Item 1) and Seal (Item 3)
• 2606467C92 Kit, Centrifuge Oil Filter consists of Filter (Not listed) and Seal (Item 3)

OPERATION
The oil pressure check valve opens at 36psi. It will then allow engine oil to enter the centrifuge
filter.
It is normal for air to flow for a short time after stopping the engine to purge oil from the
centrifuge reservoir.
Once purged the float will drop and shut off the Control Air Valve.

TROUBLESHOOTING
Run engine while visually inspecting assembly and listening for excessive noise, oil leaks, or air
leaks
• Symptom: Excessive vibration or Excess noise from centrifuge:
◦ Solution: Inspect Bearings
◾ The top bearing cannot be replaced. If it is found to be bad, a replacement
cover assembly kit p/n 3014297C92 will need to be used.
◾ The lower bearing can be replaced using Lower Bearing Kit number p/n
2610323C1. To replace this assembly you will need a 29mm socket to remove
the plastic housing. The steel sleeve insert will need to be removed if it did not
come out with the housing, as well as the spacer washer that is under the
other parts. Once all parts have been removed, clean the recess. Insert the
new brass bearing into the plastic housing from the bottom (threaded) side and
press until it seats. Rotate the brass bearing until the hole is aligned with the
hole in the housing. Insert the steel sleeve into the brass bearing. Place the
new washer into the centrifuge body recess and then thread the other three
parts back into the metal housing using Loctite 648. Tighten to 11 lb-ft torque.

https://evalue.internationaldelivers.com/service_kb/DocTool/ArticleViewer.aspx?ControlID... 3/5/2014

IK1200598 ­ Chassis Mounted Oil Centrifuge Filter Diagnostics (Air & Oil Leaks)

Page 4 of 6

◦ Only OEM filters are recomended for service changes (2606467C92). Fleetguard
filters are slightly angled and may cause the top bearing to fall out.

• Symptom: Internal Air Leak in Centrifuge:
◦ Float valve flows air constantly or not at all. Air tank bleeds down overnight.

◦ It is normal for air to flow for a short time after stopping the engine to purge oil from
the centrifuge reservoir.
◦ Once purged the float will drop and shut off the Control Air Valve.
◦ If the cover is removed before the oil is purged the oil reservoir will not drain.
◦ The float will remain up and allow air to flow through the open valve.
◦ To check float operation either re-install the cover for a few minutes until oil is
purged and air stops flowing or manually check the float buy pushing down on the
float with a steel rod. See Tool below.

◦ Solution: If air valve does NOT respond, replace valve assembly p/n 2610033C1
shown below.
–If no gasket is installed on the air valve, the air will run constantly.
–If a valve is removed, the gasket may remain stuck in the housing. If a valve is
then installed with a new gasket on it, the thickness of the two gaskets together will
not allow the air valve to open.

https://evalue.internationaldelivers.com/service_kb/DocTool/ArticleViewer.aspx?ControlID... 3/5/2014

IK1200598 ­ Chassis Mounted Oil Centrifuge Filter Diagnostics (Air & Oil Leaks)

Page 5 of 6

• Symptom: Oil leaks
◦ Clean filter assembly and run engine and visually Inspect filter assembly to identify
leak location. The entire soot centrifuge does not need to be replaced if the the oil
leak originates at a serviceable component on the soot centrifuge assembly.
◦ Leak at Cover Seal
◾ Solution: Replace Cover Seal
◾ Remove cover and cover seal. Clean seal grooves in housing and mating
surface on cover. Install a new cover seal in the housing groove, replace
cover, Orientate clamp uniformally over cover and housing flanges,
tighten clamp handle securely by hand pressure.
◦ Leak at Body to Control Mechanism Seal
◾ Solution: Replace Body-to-Control-Mechanism Seal
◾ Remove cover and centrifuge turbine assembly. Remove control
mechanism by loosening four cap screws. Discard seal and clean groove
and mating surfaces. Replace seal with a new one and retighten cap
screws alternately to 35 lb-ft torque. It is possible to rotate the body 180°
if it is necessary to locate the oil inlet port on the left side. Replace the
seal and retighten bolts.
◦ Leak at Oil Line Connections
◾ Solution: Inspect Oil Line Connections
◾ Disconnect leaking hose and remove hose adapter from port. Clean
threads in port and on adapter, and inspect for damage. Reinstall
adapter using a good liquid thread sealant. Reconnect hose.

OTHER RESOURCES:
• http://www.spinnerii.com/index.cfm/lev1/1000/divId/61/Model.560HE.Flyer
• http://www.spinnerii.com/index.cfm/lev1/726/divId/61/How.The.Centrifuge.Works
• http://www.spinnerii.com/files/comm_id_30/Spinner_560HE_bulletin_040611.pdf

SRT:

https://evalue.internationaldelivers.com/service_kb/DocTool/ArticleViewer.aspx?ControlID... 3/5/2014

IK1200598 ­ Chassis Mounted Oil Centrifuge Filter Diagnostics (Air & Oil Leaks)

Page 6 of 6

12 - OIL CLEANING CENTRIFUGE, REPLACE

Hours Code

0.8

N12‐4656U

0.8

Q12‐4656U

0.8

R12‐4656U

0.8

T12‐4656U

Model

Engine

Qualifier Qualifier Qualifier
Brakes
1
2
3

7600

With
|MAXXFORCE
2010
11/13|
Emission
Engines

8600

With
|MAXXFORCE
2010
11/13|
Emission
Engines

ProStar

With
|MAXXFORCE
2010
11/13|
Emission
Engines

5000

With
|MAXXFORCE
2010
11/13|
Emission
Engines

Transmission

Body
Style

Chassis

Transmission

Body
Style

Chassis

12 - CENTRIFUGE OIL FILTER, REPLACE

Hours Code

0.3

A12‐4656A

Qualifier Qualifier Qualifier
Brakes
1
2
3

Model

Engine

Models,
ALL

With
|All
2010
Engines|
Emission
Engines

Hide Details

Feedback Information
Viewed:

7248

Helpful:

589

Not Helpful: 459
No Feedback Found

Copyright © 2014 Navistar, Inc.

https://evalue.internationaldelivers.com/service_kb/DocTool/ArticleViewer.aspx?ControlID... 3/5/2014