1) Lift the glass cover.
2) Turn the selected burner knob to the ignite (flame) position. This allows propane to flow to the selected burner.
3) Depress the middle ignition spark knob until the burner ignites.
4) Turn the burner knob to adjust the flame to the appropriate heat setting.
5) When you have finished using the cook top, turn the burner knob to the off position allow the burner to cool before closing the
cook top cover.
Please consult the stovetop owner’s manual for complete operating and cleaning instructions.

FURNACE:
Your vehicle is equipped with a 16,000 BTU Atwood LP gas Auto Ignition Furnace. The furnace is located near the floor below the
closet. The thermostat control is located above the interior TV.
1) Ensure that there is propane supplied to the coach.
2) Ensure there is 12V power to the coach.
3) Turn the thermostat to the on position and set the thermostat to the desired temperature.
4) The Furnace will auto ignite and cycle through fan and heating. The furnace will cycle keeping the desired temperature.
5) Furnace reset button is located behind the converter through the access hole below the upper TV area drawer. Remove this
drawer to access the reset button.

Note: When the furnace is not in use, turn the thermostat switch to the off position.

24

REFRIGERATOR:
Your vehicle is equipped with a Dometic three way fridge/freezer (LP gas , AC & DC).
1) To turn the fridge on, use the mode buttons to select your power source (AC, Gas, DC or Auto). Then select your desired level of
coolness (this may vary slightly with each fridge and weather condition).
2) DC or 12 volt is used for the fridge should only be used while the vehicle is in motion of for short stops less than 3 hours.
3) The Auto is recommended when the vehicle is operating off of a 120 volt power source (shore power or generator). The fridge will
default to 120 volt then attempt to light on gas, then move to 12 volt.

NOTE: For the best cooling results your vehicle should be level and the exterior refrigerator vents free from
obstructions. Please consult your Dometic fridge-operating manual for complete operating and maintenance
instructions.

25

WATER HEATER:
Your vehicle is equipped with a Girard on demand Auto Ignition Water Heater. The water heater is located in the kitchen. You can
access the heater through the right hand kitchen lower door.
1) For normal or summer operation, ensure the switch in the outside water heater compartment is in the on position. This water
heater does not have bypass valves and is operated by the temperature control located on the kitchen lower face frame. .Please
refer to the Girard owner manual for operation.

Note: Run RV anti freeze through the water heater to winterize the heater.

NOTE: Your LP gas appliances may not light on the first try. There may be air in the LP gas lines that will
dissipate as the gas pressurizes the lines.

26

FRESH WATER SYSTEM
The water system built into your motorhome provides full service similar to the system in your home. A 12 volt self-priming pump
draws and pressurizes water from the fresh water tank to all faucets and the water heater. An automatic pressure switch located in the
water pump maintains a positive line pressure between 20 to 30 p.s.i. The fresh, black and gray water tanks are located below the
floor.

FILLING THE FRESH WATER TANK
1)
Unlock the Fresh Water Fill. Remove the large white cap.
2)
Insert a garden hose into the fill opening.
3)
Turn the water source on to a medium flow rate, as a high-pressure flow will cause water to gush out of the fill opening.
4)
Monitor the fresh water fill level using the FRS on the monitor panel located in the upper kitchen area. Do not over fill this
tank. You may see water coming out through the fill tube or air vent screen as this also indicates the fresh water tank is full.
5)
If you have over filled your fresh water tank or you want to drain some of the water out of the fresh water tank, open the
drain spigot located on the fresh water tank just in front of the hitch plates . Access this drain from the back end of the vehicle. This is
the Fresh Tank Drain.

CITY WATER CONNECTION
The city water connection is located in the driver’s side component compartment. The city water connection is a convenience for you
when you have access to an outside water source. When hooking up the city water connection you should make sure that the water
pump switch is turned off and that all water faucets are closed.
1) Open the driver side component compartment.
2) Remove the plastic insert from the city water connection.
3) Attach a garden hose to the connection using a rubber washer to ensure the fitting is tight.
4) Turn the water source on to a medium pressure.
5) Check for leaks at the city water connection, as you may have to re-tighten this connection.

NOTE: In different areas the water pressure may vary. It is advisable to use a water pressure regulator
27

because excessive pressure may result in water-line damage. The city water system bypasses the fresh water
holding tank and feeds the water lines directly so that you will not have to use the water pump. To disconnect
the city water system, first turn off the water source, then open a faucet to relieve some of the pressure in the
lines (if you do not open a faucet to relieve some of the pressure, when you unhook the water line, water may
spray out), then unhook the water line.
Water Pump
The 12 volt Sure Flo water pump is located in the kitchen lower door below the sink. The filter and the inlet connection are visible on
the top of the water pump.
Activate the water pump by using the Pump switch on the switch panels located on the kitchen upper cabinet or on the vanity upper
cabinet in the bathroom . Please consult your Sure Flo operating manual for complete operating and maintenance instructions.

TROUBLE SHOOTING:
If the pump will not prime, please check:
- to make sure there is water in the holding tank
- to make sure that the battery is not run down
- for kinks in the inlet water line
- for leaks at inlet fittings (if air is leaking into inlet fittings, tighten fittings or apply clamps as necessary)
- for clogged lines
- the inline flow filter, located beside your water pump.
If the water pressure drops:
- make sure faucet aerators are clean
- check to make sure there is water in the holding tank
- check to make sure the battery is not run down
- check faucets and connections for leaks.
If the pump runs when there is no apparent demand for water:
- make sure there is water in the holding tank
- check all faucets and fixtures to make sure they are all shut off and not leaking
- check line for leaks

28

TOILET
Please refer to the manufacturer’s operating instructions.
Toilet Trouble Shooting:
1. Water keeps running in the bowl:
check to see if all the levers are turned all the way back. Sticking may be on the waste valve blade seal at the bottom of
the bowl ,caused by foreign material on the waste valve blade seal at the bottom of the . If the problem persists, you may
need to replace the water valve.
2. The Toilet leaks, there is water on the floor:
if the leak is in the back of the toilet, check the water supply line connection and refer to the manufacturer’s installation
instructions. If the leak is at the toilet flange area (where the toilet mounts to the floor), check the toilet flange nuts and
tighten.
3. Poor flush pressure:
the levers must be held fully open during the flush. A good flush should be
obtained within 2 to 3 seconds. If the problem persists, remove the water
supply line and check the water supply. The water supply rate should be at least
10 litres/2.5 gallons per minute to ensure an adequate flush.

SHOWER
To protect the surface of your ABS plastic shower pan, it is recommended that a rubber shower mat be placed in the shower pan. Use
a non-abrasive cleaner to clean your shower pan. NOTE: Do not use highly concentrated or high acid content household cleaners, as
these may damage the shower pan.
It is recommended that the fantastic fan is run while the shower is in use to remove humidity.
It is recommended that the shower be wiped down after the shower has been used. This will help prevent mildew and other residues
from forming on shower walls.

WARNING: Before Entering the shower ensure the shower door latch is in the full open position.

Note: It is not safe to shower while the vehicle is in motion.
Note: While vehicle is in motion ensure that the shower head is in the stow position and the shower door latch
is in the locked position. Bathroom door is in the latched position.
29

WASTE SYSTEM
The Pleasure-Way Plateau XL is equipped with two waste tanks.
1) Black water tank located below the toilet under the floor of the vehicle. Only the toilet water and solid waste enter this tank.
This tank is approximately 21 U.S. gal / 79.5 L
2) Grey water tank located in the rear passenger side of the vehicle. This tank handles wastewater from the sinks and the shower.
This tank is approximately – 30 U.S. gal / 113.6 L
Before using your black water holding tank, deodorize it by adding one gallon of water and commercial tank deodorizer through the
toilet.

DRAINING WASTE HOLDING TANKS
1)
Open the driver side rear component compartment door . This will expose the sewer dump outlet. Press in the black and gray
dump valve handles to ensure the valves are closed. Remove the black termination cap.
2)
Access the sewer hose from the rear component compartment located on the driver side behind the rear wheel well. Connect
the sewer hose to the drain outlet, and put the opposite end into an appropriate sewer dump outlet

NOTE: Dump your black water first to allow your gray water to flush the black water through the hose.

3)
Open the termination valve on the solid waste holding tank (black handle). Once this tank is empty, then open the valve for
the gray waste tank (grey handle). A garden hose may be left running into the toilet with the valve open to further rinse the tank and
sewer hose.
4)
Close the termination valves and replace the cap/ Rinse and store your sewer hose back in the canister.
Deodorize the empty tank by adding one gallon of water and commercial holding tank deodorizer through the tank.

NOTE: If the black water holding tank is allowed to overfill, the overflow may back up through the toilet drain.
NOTE: If the gray water tank is allowed to overfill, the overflow may back up through the shower drain.
If you are using a sewer hook up in a RV park, keep the valve closed until the holding tank is at least partially full, then drain. The
large quantity of waste flow will provide more effective drainage and reduce tank stoppages.

30

WINTERIZING
1) Drain your fresh water tank This drain is located on the water tank located behind the driver rear wheel in the center of the
vehicle.

2) Remove the water line from the inlet side of the water pump (this is the clear plastic line going into the water pump filter.)
Connect a siphon hose to the inlet side of the water pump place the other end in a container RV non-toxic antifreeze. Turn on
you’re the pump. This will pump non-toxic RV antifreeze through all of your fresh water lines.

NOTE: Siphon hose consists of 40” of ½” clear tubing with a fitting to attach to the water pump. The fitting
can be purchased through an RV dealer.

3) Open the kitchen and bathroom faucets one at a time allowing the antifreeze to flow through both the hot and the cold sides. Be
sure to also open the toilet valve and exterior shower faucet. Turn off the water pump and disconnect the siphon hose, reattach
the original fresh water supply fitting.
4) Pour ½ cup of RV antifreeze down each drain (kitchen sink, bathroom sink and shower drain).
Note: The water heater does not have to be bypassed for winter. Anti-freeze can be passed through the water heater.
5) Fully charge your auxiliary coach battery and turn off the red disconnect. The red disconnect is located on the entrance switch
panel.

6) Turn you thermostat to the off position. (see picture above)

31

7) Turn your propane tank off. (see picture above)
8) Place your fridge door in a slightly open position for air to circulate through the fridge..

Note: It is recommended that you start and run your vehicle and generator once a month during the winter
season.

WINTER USE
We recommend that the water system not be used when the outside temperature drops below the freezing point. You should ensure
that your unit is completely winterized by that time. If it is necessary to use the water system, we suggest that you bring containers of
fresh water with you and add non-toxic RV antifreeze to the gray and black water holding tanks. NOTE: Keep in mind that as you
add more water to the holding tanks the antifreeze will dilute more than the recommended amount and may start to freeze earlier at
cold temperatures. Do not use the exterior shower.

LOW POINT DRAIN VALVE
Located under the rear bumper close to the driver side hitch plate.. This Low point drains will allow you to drain your water line
system. There are three drains in this area .two on blue lines and one on a red line.

32

LIVING AREA ELECTRICAL SYSTEM
The Motorhome living area electrical system is designed for convenience. It is capable of supplying the vehicle with at least two
sources of power. A 12 volt auxiliary battery supplies power to the interior components (except AC current plug receptacles, roof air
conditioner, microwave, and fridge on AC) for short-term use. The auxiliary coach battery is charged when the chassis engine is
running or when you are plugged into a 110 volt power source (shore power or generator) with the disconnect switch in the on
position.
For long term use, your vehicle may be powered by plugging into a 110 volt external power source with the supplied 25 foot power
cable. The yellow 25 foot power cable supplied with your coach must be connected to your coach and then to a 110 volt power source
(30 amp outlet is recommended). This will supply 110 volt power throughout the interior and supply power through a power converter
to all 12 volt components.

NOTE: Connect the power cord to your coach first and then the external power source.
Your unit is equipped with a 110/12 volt power converter. Its function is to take part of the 110 volt current that is received when the
unit is plugged into an external power source and convert it to 12 volts (which powers most of the motorhome components).

Note: All dash components including the in dash Radio/and front Map Lights are powered through the starting
battery or Chassis battery prolonged use of these items when the vehicle is not running will deplete the engine
starting battery.
12 volt or DC Equipment
TV & DVD inverter
Refrigerator when on LP gas or DC
Interior & Exterior Coach Lights
Antenna Booster
Water Pump
Water Heater
LP gas & CO Alarms
Generator Start Switch
Furnace
Power Sofa
Fantastic Fan ( if equipped)
Awning
Power step
Monitor Panel
Water heater
Exterior DVD player

110 volt 0r AC Equipment
TV and DVD when plugged into the AC receptacle
Refrigerator on AC
Microwave/Convection Oven
Air Conditioner
110 volt Plugs
110 /12 volt Power Converter

33

AC ELECTRICAL DISTRIBUTION PANEL
The Pleasure-Way Prestige is equipped with AC distribution panel that houses the breakers for the 110 volt. The distribution panel is
located on the passenger side under the entertainment center. The breakers act like a household breaker you must insure the breaker is
all the way off before you can reset the breaker.

First breaker in the panel 30 Amp Main
(1) 15 Amp Microwave/Convection oven
(2) 15 Amp Rear plug/ Entertainment Center
(3) 15 amp Bathroom, Galley, Fridge,
Exterior Plug
(4) 15 Amp Converter
(5) 20 Amp Air Conditioner

Note: Check the GFI in the kitchen galley if the fridge, bathroom, kitchen or exterior plug is not working.
12 VOLT DC BREAKERS AND DC LOAD CENTER
This load center is located in the lower door on the passenger side above the furnace.

o
w
e e
n r
e
r S
a o
t f
o a
r

n
v
e
r
t
e
3 r
4 0
s
0

h
a
r
g
e

a
L
A 6 t
A m ti
0
n
mp
e
e
p
Ar
my
8
p
0
D
i
sA
m
c
34
p
o

12 VOLT BATTERY DISCONNECT SWITCH
There is 12 volt disconnect switch located by the main entrance door in the switch control panel . This disconnect/breaker will stop all
12 volt power supplied to your coach from the auxiliary batteries. The disconnect switch will have to be in the on position to charge
your battery from the converter in this vehicle. If your vehicle is going to be parked for longer than a 48 hour period, turn this switch
to the off position as the CO detector and the LP detector are hard wired to the coach battery and will eventually drain the battery.

12 VOLT DC UPPER FUSE PANEL
Upper Panel
Access to the upper fuse panel is through the cabinet style next to the driver side kitchen upper door, behind the upper switch panel ,
inside the vehicle. For ease of access open the kitchen upper door and snap the style off.

Fuse Schematic
#

Switched Loads

1
2
3
4
5
6
7
8
A
B

Living Room Lights
Kitchen Lights
Counter Lights
Bathroom Lights
Entry Lights
Porch Light
Sofa Valance
Vanity Light
Spare
Fantastic Fan

Fuse Size
10 Amp
10 Amp
10 Amp
10 Amp
10 Amp
10 Amp
10 Amp
10 Amp
10 Amp
10 Amp

Output
Dimming
Dimming
Dimming
Dimming
Dimming
Non-Dimming

Constant
Constant
35

CONVERTER- AND OUPTUT FUSE
Located below the closet lower drawer. Remove the drawer to access this area. There are two 30 amp blade fuses on the converter.

AUTOMATIC TRANSFER SWITCH
The automatic transfer switch is located behind the kitchen lowest large pot drawer. To access the transfer
switch you must remove the lower drawer by releasing the slide locks on each side.
The Automatic transfer switch will only allow your coach to get power from one source either the generator or
the shore power cord. This is a safety feature of this vehicle.

AUXILIARY BATTERY
The coach or auxiliary batteries is located under the hood of the vehicle. . This battery operates the Motor Home portion of your
vehicle. This battery is a Mercedes multi-purpose battery with a 95 AH rating.
The engine starting battery is located below the driver floor in front of the driver seat.

The Mercedes Sprinter chassis battery/engine starting battery is located below the driver floor in front of the
driver seat. Consult your Mercedes Sprinter owner’s manual for details.
BATTERY CARE
Your auxiliary battery supplied by Mercedes Please refer to the sprinter manual . To ensure satisfactory battery performance, battery
terminal cleanliness is essential. NOTE: Please consult your Ford manufacturer’s instructions for detailed maintenance
recommendations for the vehicle battery.

Warning: Batteries give off explosive gases that can cause severe personal injury. Do not smoke in or around
the battery and keep open flames and other sources of ignition well away from the battery. Remember that
batteries can and do, EXPLODE! Be very careful. Battery electrolytes can cause severe eye damage and skin
burns. Always wear protective equipment (goggles, rubber gloves, a protective apron, etc.) when working with
batteries.
36

EXTERNAL POWER
A 25- foot, 30 amp power cord is provided with your Pleasure-Way motorhome. In order to activate all power circuits, connect the
yellow power cord to your coach in the driver’s side rear compartment and to an adequate 110 volt power source. The connector is
rated for 30 amp capacity. NOTE: The male end of the power cord is a 30 amp plug, therefore you may require an adapter to convert
the plug into the 110 volt style. Most RV parks are equipped with 30 amp plug-ins. Remember to always attach the power cord to
your coach first, and then to the power source

MONITOR PANEL AREA
There is a monitor panel located on the kitchen upper cabinet end panel. Located on this panel are the monitors the for the (1) Fresh
Water (2) Grey Water (3) Black Water, (4) LP gas (5) generator hours (6) coach battery charge level.
Pleasure-refer to the Monitor Panel owner’s manual for instructions.

37

GENERATOR
If your unit is equipped with a generator, it will be located on the driver’s side. Access to the generator is through the non- locking
middle compartment door. There is no access to the generator through the interior of the coach. This prevents exhaust gases from
seeping into the living compartment. The generator will provide an added source of power to run the electrical system when you are
not plugged into a 110 volt power source.

Starting the Generator:
1) Turn on the red disconnect switch.
2) Turn on the LP tank by opening the valve on the tank.
3) Press the generator start switch in the Switch panel on the kitchen upper cabinet face or on the entrance switch panel.
4) The hour meter for your generator is located on the kitchen upper switch panel.

Gen

.

Switch

NOTE: It may take a few seconds initially for the generator to start. Your generator draws its gas supply from
the LP tank air may have to be purged from the line. Once the generator is running, it supplies power to the
entire electrical system, just as if your unit was plugged into a 110 volt power source. You will have to balance
your electrical consumption as you have a limited number of watts/ amps available.
NOTE: Please refer to the generator’s manufacturer’s operating manual for complete operating instructions
and maintenance procedures.
NOTE: If your unit is equipped with a generator, it is essential that you run your generator at least ½ hour a
month under load (microwave, AC, coffee maker, etc.) to keep the generator maintained and lubricated.
NOTE: For your safety and protection, all generator or generator-ready units are equipped with an
automatic transfer switch that will allow your coach to receive power from either shore power or your
generator.
38

MOTORHOME INTERIOR
INTERIOR COCKPIT MAP LIGHT
Please follow the vehicle manufactures instructions for operating procedures. This light is operated from the engine starting battery
prolonged use will deplete the engine starting ability.

REFRIGERATOR - DOMETIC
Your Dometic refrigerator is designed for 3-way operation, using, 110 volt AC, 12 volt DC and LP gas power. When the refrigerator
is switched to A or /DC the ammonia/water mixture is heated by a heating element instead of a burner.
When your motorhome is stationary, it should be leveled for your refrigerator to provide the proper cooling. A bubble level should be
placed on the freezer shelf to check the refrigerator for levelness. If the refrigerator is not level you may have improper cooling.

NOTE: Please refer to the Dometic operating manual for complete operating instructions and maintenance
procedures.

MICROWAVE/CONVECTION OVEN (PICTURE ABOVE)
Your Micro/Convection oven operates off of 110 volt AC power only. To use your microwave you must be plugged into shore power
or have the generator running.

39

NOTE: You will not be able to run your microwave /convection oven at the same time as your roof air if you
are running on you generator power.
Please refer to the manufactures operating instructions for maintenance, operation and cooking.
TV AND DVD
Your motor home is equipped with TV and Blu-ray DVD components, you will find these located in the entertainment center. These
two components are powered by a 110 volt power source (inverter or shore power)

NOTE: Your DVD is a player only as it will not record. To play a CD or MP3 the TV flat screen must be in the
on position.
32” THEATRE SYSTEM
BASIC OPERATING PROCEDURE
For addition TV, DVD, Antenna, or Inverter additional information please refer to the appliance owner manuals.

A) COMPONENTS:
1)
2)
3)
4)

32” Flat Screen Monitor
Blu-Ray DVD player
Inverter for 12 volt operation
Antenna with booster

B) BASIC TV OPERATION:
TV antenna (rotate the TV antenna for best reception) or hook up to park cable.

40

12 Volt Operation:
1)

Turn the inverter on. The located in the cabinet directly below the DVD player. Your vehicle is equipped with two inverters
the inverter on the right is used for the inside entertainment system. The inverter on the left is used for the exterior TV.
(Switch is located beside the fan on the back of the inverter opposite end as the plug outlet). Ensure the TV and DVD player
are plugged into the inverter and the inverter is turned on.
Off/On
Switch

(1)

(2)

(2)

2)
Turn the antenna booster on by pressing the black button just above the inverter on the white wall plate. (green light indicates
booster on) Turn the antenna booster on the antenna base.
3)
Turn the TV on and select DTV-TV using the input button on your TV or remote.
4)
Using the menu button select - TV, select -Channels, select - Scan Channel. This will bring in all local air channels.
5)
For Cable TV connect a cable extension cord from the cable hookup in the component compartment to the park cable outlet.
Turn the booster off on you TV antenna follow step (4) for auto programing.
6) For DVD operation turn on the DVD player. Using the source button on you TV or TV remote select HDMI 1. Insert a DVD
or Blu-Ray Disc allow the Disc to load and press play.
• To save power while watching TV ensure the DVD player is switched off. Only turn your DVD player on when in use.

For 120 volt Operation
(Generator or Shore Power):
Plug the TV and DVD player into the outlet located above the inverter. Switch the inverter off (Switch is located beside the fan on the
back of the inverter opposite end as the plug outlet).. Use the same programing procedures as the 12 volt operation.

Exterior Entertainment Center (see above)
The TV operates off of the 110 volt system you will find the inverter (right hand side) and AC plug
in the same cabinet as the interior entertainment center. The exterior DVD/radio unit is a 12 volt
system, this unit will operate independently of the TV for playing all sources. Please be aware that
there is no AM antenna attached to this unit. When this unit is not being used ensure the power is
switched off on the player. The blue lights from the speakers will turn off with the DVD player.

41

FULL SIZE BED ASSEMBLY
POWER SOFA
SOFA BED AREA 41 X 67 ½”

1) Power Sofa Operation:
Remove the front and rear sofa arm rest from the retainers.
Extend the power sofa with the sofa Slide Switch. The Slide Switch is located on the kitchen upper
cabinet switch panel the left hand switch will extend you power sofa

Sofa Switches
#1 extend
#2 retract

For Safety: Pull down the step cover located on the passenger front entrance wall below the fire extinguisher.
Ensure the step cover is flipped up and in the stored position when the exterior main entrance door is in the open
position. (Picture 3)

(1)