Loading...

NHTSA ID Number: 10130294

Manufacturer Communication Number: GCI-A0250-02

TSB/Document Date: 2018-03-13


Summary

GENERAL CONSUMER INFORMATION PERTAINING TO AN OWNER'S MANUAL


necessary to use the water system, we suggest that you bring containers of fresh water with you and
add non-toxic RV antifreeze to the gray and black water holding tanks. NOTE: Keep in mind that
as you add more water to the holding tanks the antifreeze will dilute more than the recommended
amount and may start to freeze earlier at cold temperatures. Do not use the exterior shower.
Living Area Electrical System
The Motorhome living area electrical system is designed for convenience. It is capable of
supplying the vehicle with at least two sources of power. A 12-Volt auxiliary battery supplies
power to the interior components (except AC current plug receptacles, roof air conditioner,
microwave, coffee maker and fridge on AC) for short-term use. The auxiliary coach battery is
charged when the chassis engine is running or when you are plugged into a 110 volt power source
with the disconnect switch in the on position.
For long term use, your vehicle may be powered by plugging into a 110-Volt external power source
with the supplied 25-foot power cable. The yellow 25-foot power cable supplied with your coach
must be connected to your coach and then to a 110 volt power source (30 amp outlet is
recommended). This will supply 110-Volt power throughout the interior and supply power through
a power converter to all 12-Volt components.
NOTE: Connect the power cord to your coach first and then the external power source.

Your unit is equipped with a 110/12-Volt power converter. Its function is to take part of the 110Volt current that is received when the unit is plugged into an external power source and convert it
to 12-Volts (which powers most of the motorhome components). It also provides 110-Volt power
to the components that only require 110-Volts.
NOTE: The 12-Volt or DC power on your fridge should only be used while in motion or running

the vehicle engine.
12 volt or DC Equipment
TV when plugged into the Inverter
Refrigerator when on DC or LP gas
Interior & Exterior Coach Lights
DVD Player, Antenna Booster and Amplifier
Water Pump
Water Heater
LP gas & CO Alarms
Generator Start Switch
Furnace
Power Sofa (if equipped)
Air Ride Compressor (if equipped)

110 volt 0r AC Equipment
TV when plugged into the AC receptacle
Refrigerator on AC
Microwave
Air Conditioner
110 volt Plugs
Coffee Maker (if equipped)

28

Electrical Distribution Panel
The FordeBay logo Excel is equipped with an Iota distribution panel that houses the breakers for the 110-volt
system and the blade fuses for the 12-volt system. The distribution panel is located on the
passenger bench face in the TD model and on the sofa bench face in the TS and RD model.
Remove the large vertical smoked plastic cover panel to access the 110-volt breakers or the small
horizontal cover panel for the 12 volt fuses.

12-Volt Manual Reset Breakers and Converter Output Fuses
Your motorhome has manual re-settable breakers. If you have the optional electric rear sofa, you
will have three manual resetting breakers. These manual re-setting breakers are labeled. Access to
these breakers is through a compartment door found on the passenger side underneath the furnace.
These breakers have a 40, 30 and 20-amp capacity. The 40-amp breaker controls the power
converter, the 30-amp breaker controls the power sofa and the 20-amp breaker controls the
refrigerator when it’s running on 12-Volts. There is also an 80-amp charge-line breaker.
If you are experiencing any difficulties with your power converter, refrigerator, electric sofa or
charging system while on 12-Volt, check these breakers first to determine if they are tripped. There
is a small re-set button located on the end of the breaker. Simply push it in if it is tripped.

29

12-Volt Battery Disconnect Switch
There is 12-Volt disconnect switch (red key) located on the passenger side through a compartment
door found beneath the furnace (same compartment as the manual reset breakers). When the key is
in the “ON” position it will be locked in place. When the key is in the “OFF” position it can be
easily removed, which will stop all 12-Volt power supplied to your coach. Note: The disconnect
switch will have to be in the on position to charge your battery from the converter in this
vehicle. If your vehicle is going to be parked for longer than a 48 hr period, turn this switch to
the off position as the CO detector and the LP detector are hard wired to the coach battery
and will eventually drain the battery.

Auxiliary Battery
The auxiliary battery (coach battery) is located on the passenger side in a battery pull out tray. It is
an Interstate SRM 24 Marine / RV deep cycle battery. This battery operates the Motor Home
portion of your vehicle only.
The chassis battery and auxiliary battery are two separate
systems. Both batteries are charged from the alternator, but
only the auxiliary battery is charged from the converter.
The Chassis battery powers all chassis related items such as
the map light between the driver and passenger seat, all
dash features, driving lights, power mirrors, locks and
windows.
The auxiliary battery powers all living area lighting, DC
appliances and air ride compressor.

The FordeBay logo chassis battery is located under the front engine hood. Consult your FordeBay logo owners
manual for details.
Battery Care
Your auxiliary battery must be regularly cleaned and maintained at least once a month in order to
provide a reliable and constant power source to your Motorhome. To ensure satisfactory battery
performance, battery terminal cleanliness is essential. NOTE: Please consult your DODGEeBay logo
manufacturer’s instructions for detailed maintenance recommendations.
30

Warning: Batteries give off explosive gases that can cause severe personal injury. Do not smoke
in or around the battery and keep open flames and other sources of ignition well away from the
battery. Remember that batteries can and do, EXPLODE! Be very careful. Battery electrolytes
can cause severe eye damage and skin burns. Always wear protective equipment (goggles, rubber
gloves, a protective apron, etc.) when working with batteries.
External Power
A 25- foot, 30-amp power cord is provided with your Pleasure-Way motorhome. In order to
activate all power circuits, connect the yellow power cord to your coach in the driver’s side
component compartment and to an adequate 110-Volt power source. The connector is rated for 30amp capacity. NOTE: The male end of the power cord is a 30-amp plug, therefore you may
require an adapter to convert the plug into the 110-Volt style. Most RV parks are equipped with
30-amp plug-ins. Remember to always attach the power cord to your coach first, and then to the
power source.
Monitor Panel Area
There is a monitor panel located above the passenger side entry door. Located in this panel is the
carbon monoxide sensor, water heater control switch, generator control switch (optional) and the
water pump control switch, which also monitors the black water, gray water, fresh water and coach
battery charge level.

Generator
If your unit is equipped with a generator, it will be located directly behind the driver door. Access
to the generator is through the locking compartment door. There is no access to the generator
through the interior of the coach. This prevents exhaust gases from seeping into the living
compartment. The generator will provide an added source of power to run the electrical system
when you are not plugged into a 110-Volt power source.
Starting the Generator:
1) Turn on the red key disconnect switch.
2) Ensure there is at least a ¼ tank of gas as the generator runs off the van chassis fuel tank. If
there is less than a ¼ tank of fuel, the generator will not start.
3) Press the generator start switch in the monitor panel area.
NOTE: It may take a few seconds initially for the generator to start. Your generator draws its gas
supply from the van chassis fuel tank. Once the generator is running, it supplies power to the entire
electrical system, just as if your unit was plugged into a 110-Volt power source. You will have to
balance your electrical consumption as you have a limited number of watts/ amps available.
31

Please refer to the generator’s manufacturer’s operating manual for complete operating instructions
and maintenance procedures.
NOTE: If your unit is equipped with a generator, it is essential that you run your generator at least

½ hour a month under load (microwave, AC, coffee maker, etc.) to keep the generator fuel from
damaging the carburetor.
NOTE: For your safety and protection, all generator or generator-ready units are equipped with an

automatic transfer switch that will allow your coach to receive power from either shore power or
your generator.
MOTORHOME INTERIOR
Interior Cockpit Map Light
Please follow the vehicle manufactures instructions for operating procedures.
Refrigerator - Dometic
Your Dometic refrigerator is designed for 3-way operation, using 12-Volt DC, 110-Volt AC and LP
gas power. When the refrigerator is switched to AC or DC, the ammonia/water mixture is heated
by a heating element instead of a burner.
When your motorhome is stationary, it should be leveled for your refrigerator to provide the proper
cooling. A bubble level should be placed on the freezer shelf to check the refrigerator for
levelness. If the refrigerator is not level you may have improper cooling.
NOTE: Please refer to the Dometic operating manual for complete operating instructions and
maintenance procedures.
NOTE: The DC or 12-Volt setting is for transportation purposes only. It is recommended that if
you are going to be stopped for more than a short period of time, you should switch your
refrigerator to propane or an AC setting and plug into a 110-Volt supply. The refrigerator should be
turned to 12-Volt when the vehicle will be in motion and the LP gas must be turned off.
Microwave- Dometic
Your Dometic microwave operates of 110-volt AC power only. To use your microwave you must
be plugged into shore power or have the generator running (the microwave cannot be used at the
same time as the roof AC unit when operating on the generator).
NOTE: Please refer to the manufactures operating instructions for maintenance, operation and
cooking.

32

TV and DVD (Optional)
If your motor home is equipped with TV and DVD components, you will find these located in the
rear entertainment center. These two components are powered by a 12-Volt power source. The TV
flat screen is powered by a 12-volt inverter located behind the flat screen.
NOTE: Your DVD is a player only as it will not record. To play a CD or MP3 the TV flat screen
must be in the on position.
NOTE: Ensure the TV travel lock is locked into the travel position when the vehicle is in motion.
The travel lock is located on the bottom left hand corner of the TV cabinet.

19” THEATRE SYSTEM
Basic Operating Manual

A) COMPONENTS:
1)
2)
3)
4)
5)
6)
7)
8)
9)

19” Flat Screen Monitor with swing out cabinet
DVD/CD/MP3 player
400 watt Inverter
Amplifier
Noise reduction ground loop
Auxiliary power switch
Satellite speakers
Antenna booster
Optional AC power source

B) BASIC OPERATION:
1) Turn the auxiliary power switch to the on position. This is the switch to the left of the dvd
player.
Note: you will hear a fan noise run when you are powering your TV through the inverter.
(If you are powering your TV through the inverter and the fan does not come on check the
power switch at the bottom of the inverter.)
2) Turn on the TV using the small button on the bottom right hand side of the TV.
3) Using the source button, select AV for the DVD player or Antenna if you want local air or
cable channels.
33

4) For Cable simply turn off the antenna booster (located behind the flat screen) leaving the
source on antenna.
Note: for local air channels ensure your antenna is cranked up and the antenna booster
switch is in the on position. The antenna booster switch is located You may have to rotate
your antenna for better reception.
5) Receiving channels above 13 :
a) Push the menu button.
b) Using the channel down button move to the satellite symbol.
c) Push the enter button. (second button from the right at the bottom of the TV) AIR
/CABLE will be in yellow hi-lights.
d) Push the enter button and just AIR will be in yellow hi lights. Using the channel down
button move the yellow hi lights to STD.
e) Push the enter key
f) Push the menu button three times to return to regular TV screen

6) To AUTO PROGRAM your TV for air or cable channels:
a)
b)
c)
d)
e)
f)
g)

Push the menu button.
Using the channel down button move to the satellite symbol.
Push the enter button. AIR/CABLE will be in yellow hi lights.
Using the channel down button move the yellow hi lights to AUTO PROGRAM.
Push the enter button.
The AUTO PROGRAM key will appear with START in yellow hi lights.
Push the enter button. Auto programming will begin with STOP in yellow hi lights. If
you wish to stop the auto programming hit the enter button and start will appear.
h) Push the menu button to return to the regular TV screen.

C) POWER SOURCE :
There are two options for AC power on your TV system.
For operation the power button to the left of the DVD player must be in the on position.

34

1) When the motor home is not plugged in to an outside power source or not operating off
your generator, the power source is through your DC battery and the inverter. The inverter
is located behind the TV flat screen. The inverter has a power switch located on the unit. A
fan will run when the inverter is on.

1) When the motor home is plugged in or operating off of the generator there is an AC power
outlet located behind the TV flat screen. Unplug the AC power cord from the inverter and
plug it into the AC outlet. Turn off the inverter to eliminate the inverter fan noise.
A) 400 watt inverter
B) Amplifier
C) Noise reduction ground loop
D) Antenna booster
E) AC Power Source

Antenna Booster
A) Green indicator light
B) Booster Off/On switch.
C) 12 volt power source 3 amp

35

TD Full Size Bed Assembly
To make up the Full-size bed in the TD model, lift the center removable night table and place it on
the floor.

Lift the passenger side single bed and remove the cushion support boards. Place the cushion
support boards on the support rails between the passenger and driver side bench faces.

Finally, place the side backrest cushions in between the passenger and driver side single beds.

36

TS Bed Assembly
Using the sofa bed switch beside the DVD player lay the sofa bed down to a flat position. You can
sleep with the sofa bed in this configuration (U shape) as two single beds with the space between
the two ottomans open.

You can also use the cushion support board (located in the closet) to make a full king-size bed.
Place the cushion support board on the support rails between the two ottoman benches. Place the
ottoman cushions on the inward side of the ottoman rails. This will ensure the ottoman backrest
cushions fit tight between the ottoman cushions. Place the ottoman backrest cushions on the bed
board between the ottoman seat cushions.

FordeBay logo Excel :

TD

TS

RD

Dometic 3-way Refrigerator
Dometic .7 cu.ft. Microwave
2 Burner Flush Mount Cook Top with Glass Cover
Suburban 16,000 BTU Auto Ignition Furnace
Suburban 6 gal Auto Ignition Water Heater
Sure-Flo Demand Water System
Thetford Flush Toilet
Self Contained Bathroom with Shower & Sink
C.O. Detector
LP Gas detector
Smoke Detector
Fire Extinguisher
Fantastic Fan Roof Vent
Coach Battery
Battery Disconnect Switch
45 amp Power Converter with Distribution Panel

X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X

X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X

X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X

37

Monitor Panel System (Black, Gray, Fresh water, Battery)
Fresh Water Fill
Fresh Water Tank (91 L or 24 U.S. Gal)
Grey Water Tank ( 97 L or 26 U.S. Gal)
Black Water Tank (45 L or 12 U.S. Gal)
Generator Ready ( switch, wire for connections & mount
brackets)
Exterior Shower
*Rear Bed Area ( 74” X 81”)
*Power Sofa
*Rear Bed Area ( 54” X 81”)
Awning Style Windows
Large Round Table
Porch Light
Cable TV Hook Up
TV Antenna
Water Heater By-Pass
Fiberglass Running Boards
Counter Top Flip Up
Exterior Plug

X
X
X
X
X
X

X
X
X
X
X
X

X
X
X
X
X
X

X
X

X
X
X

X

X
X
X
X
X
X
X
X
X

X
X
X
X
X
X
X
X
X

X
X
X
X
X
X
X
X
X
X
X

NOTE: Pleasure-Way Ind. Ltd. reserves the right to make product changes at any time with out
prior notice or obligation.

The bed area measurements may vary, due to components inside the vehicle.

38

123

SaleBestseller No. 1
Autel Scanner MaxiCOM MK900BT, 2026 MK900-BT V2.0 Bidirectional Diagnostic Tool, 8in Up of MK900 MX900 MK808S MK808BT MX808S MK808Z, 3000+ Active Tests, 40+ Service, CAN-FD&DOIP, All System, FCA 11 OS
  • 💯【Conta.ct us for Support Directly】If you met any...
  • 🔥🔥🔥【2026 AUTEL FLAGSHIP MK900BT MK900-BT, NEW...
  • 🚗【3000+ ACTIVE TESTS (50➡3000+), SAME AS MS...
  • 🚗【40+ HOT SERVICES FOR 150 MAKES (28+➡40+)】Full...
  • 🚗【OE ALL SYSTEM DIAGNOSE, AUTO SCAN 2.0: SCAN LICENSE...
SaleBestseller No. 2
Autel Professional OBD2 Scanner AL319 Code Reader, Enhanced Check and Reset Engine Fault Code, Live Data, Freeze Frame, CAN Car Diagnostic Scan Tools for All OBDII Vehicles After 1996, 2026 Upgraded
  • 【TURN OFF CEL】 This AL319 car scanner diagnostic tool...
  • 【EXTENSIVE APPLICATION】 Autel AL319 Compatible with...
  • 【FOR END USER & DIYERS】 This error code reader AL319 is...
  • 【USER-FRIENDLY DESIGN】 This OBD2 scanner and check...
  • 【HIGH-QUALITY SERVICES】 12 months war.ranty from the...

Last update on 2026-06-23 / Affiliate links / Images from Amazon Product Advertising API


 


If the PDF is very large, it may not load in the preview below.

Download PDF [938.67 KB]


Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.

If the TSB PDF does not show, download or view it on the NHTSA Website.

Click on the (+) Plus Sign

Then Click on Associated Document(s)


Search NHTSA Database for Recalls

View Latest Recalls


Search NHTSA Database for Vehicle Investigations

View Latest Vehicle Investigations


Search NHTSA Database for Vehicle Complaints

View Latest Vehicle Complaints


TSB/Document ID: GCI-A0250-02

Replacement Service Bulletin Number:

MFR Communication Date: 2018-02-07

MFR Internal Campaign ID/Software Version:

Communication Type: Service Bulletin/Repair Instructions

NHTSA Components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL

MFR Component System:

MFR Component Subsystem:


Previous TSB

Next TSB



SaleBestseller No. 1
Bidirectional OBD2 Scanner Diagnostic Tool VDIAGTOOL D200, Bluetooth Scan Tool-Lifetime Free Updates, 26 Resets (Unlockable 49+), Full System Car Code Reader for iOS & Android, FCA AutoAuth & CAN-FD
  • 【OE-Level Full System Diagnostics-Lifetime F*REE Software Updates】The VDIAGTOOL D200 OBD2 Scanner for cars is a all system bidirectional scan tool that enjoy lifetime f*ree software updates, delivers complete system coverage. reading/clearing codes across engine, transmission, ABS, SAS, EPB, TPMS plus full access to body, chassis, powertrain and all control modules. This D200 Bidirectional car scanner works with most 1996+ OBD2 gasoline and hybrideBay logo cars and light trucks. It does NOT support pure electric and heavy-duty trucks. PLEASE CHECK COMPATIBILITY BEFORE ORDERING or Contact us with VIN to confirm compatibility.
  • 【Supports OBD2 Full Functions-ZERO Subscription Fees】D200 Bidirectional OBD2 Scanner is a upgarde of universal car code reader. It supports OBD2 full functions to help you turn off the annoying instrument fault indicator, such as read/clear codes, O2 sensor test, I/M readiness, on-board monitor test, datastream, freeze frame, E-VAP system test, and retrieve vehicle information. This professional obd2 scanner diagnostic tool can full access to diagnostics, reset tools and maintenance features with a single payment. NOTE: The fault code can only be cleared after the vehicle's malfunction has been repaired; please ensure the vehicle issue is fixed before clearing the code.
  • 【D200 Hidden 2 Advantages: 1. $169 Expandable 49+ Advanced Resets. 2. $199 Get J2534 P*a*s*s-Thru Programming】Your core car diagnostics and 26 reset remain lifetime f*ree for everyday maintenance. When you need deeper repair capability, upgrade with 3-year access for $169 in Store on VDIAGTOOL App, gaining 49+ advanced resets. D200 configured with J2534 hardware, upgrade only when you need without replacing the entire device. You also can Lifetime Unlock for $199 in Store one-time, perform module programming, software re~flashing and ECU data updates directly. Supports 17+ major brands, including for BMWeBay logo, for AudieBay logo, for GM, for FordeBay logo and more. Note:D200 does‘t provide any OE software.
  • 【Full Bidirectional Control / Active Tests】The D200 car scanner diagnostic tool is a true bidirectional scan tool that lets you send commands directly to the vehicle’s ECU for active tests. Quickly test fuel pumps, relays, solenoids, injectors, cooling fans, windows, sunroofs and more to verify operation instantly. Get dealership-level diagnostic control at a fraction of the cost (ofter $100-200$ per diagnostic visit), reduce guessworkand confirm repairs faster, avoid unnecessary parts replacement, towing fees and wait times.
  • 【26 F*ree Essential Reset & Relearn Functions – Everyday Maintenance Made Easy】Handle common maintenance and repair jobs without visiting the shop. The D200 code readers & scan tools includes 26 f*ree high-demand reset functions, including Oil Reset, EPB Service, SAS Calibration, ABS Brake Bleeding, Throttle Relearn, Injector Coding, Headlight Adjustment, Tire Size Reset and more. Perfect for home car owners, mechanics and DIYers – just plug and diagnose anytime, anywhere! Note: Service functions vary by vehicle model—please confirm compatibility.
SaleBestseller No. 2
VDIAGTOOL VD10 OBD2 Scanner Code Reader Car Diagnostic Tool Engine Fault Code Reader for Turn Off CEL with Freeze Frame/I/M Readiness for All OBDII Protocol Cars, OBD2 Scanner Diagnostic Tool
  • 【A MUST-HAVE TOOL FOR DIYERS】 - VDIAGTOOL VD10 car code reader is an incredibly useful obd scanner for each car owner or hobbyist, even for those with little to no experience when it comes to vehicle mechanics! Similar to a fixd car diagnostic tool, using this car diagnostic scanner is extremely easy. All you have to do is attach it to your car OBDII port and you can diagnose car problems in seconds! Read Codes (DTCs); Clear Codes; Live Data; View Freeze Frame; I/M Readiness; Vehicle Information.
  • 【KEEP ENGINE IN GOOD STATUS】 - VDIAGTOOL check engine code reader brings a fast access to scan, read the car fault code, show its definition on the screen instantly, troubleshooting to find the root causes of problems, erase the engine fault code and turn off the MIL (Malfunction Indicator Light). Similar to a fixd car diagnostic tool, this car code reader helps ensure your engine stays in top condition.
  • 【READ/CLEAR CODES & DTC LOOKUP】- No search online & saving your time, this vehicle car code reader retrieves generic (P0, P2, P3, and U0), manufacturer specific (P1, P3, and U1) codes, pending codes and displays DTC definitions based on the built-in database(more than 3000 codes) on the TFT screen, find out the root causes and clear the codes after fixed.
  • 【LIVE DATA & RETRIEVE FREEZE FRAME】 - This diagnostic scan tool for accurate diagnosis enables you to retrieve data from vehicle sensors, such as Engine RPM, Intake air temperature, Short/Long term fuel, Misfire data and etc. The freeze frame is stored in the PCM together with the diagnostic trouble code (DTC) related to the fault. Comparable to a fixd car diagnostic tool, the VD10 car code reader car scanner can be a valuable & practical diagnostic aid and also greatly help when diagnosing intermittent problems.
  • 【I/M READINESS for THE S-nn-0-g CHECK】- OBDII vehicle may not pass the annual inspection unless the required monitors since reset are complete. So you should at least read the readiness monitors and make sure they are ready. This car obd2 scanner diagnostic tool is equipped with I/M readiness function to check the operations of the e-m-issi0n system on OBD2 compliant vehicles, run I/M monitor readiness test, checking if the pass vehicle s-m-0-g inspection.
Bestseller No. 3
VDIAGTOOL Bidirectional Scan Tool VD80 BT Lite, 2026 8" Wireless Full System OBD2 Scanner Diagnostic Tool with 28+ Resets, ECU C0ding, Oil/Brake/BMS/SAS, FCA, CAN FD & DoIP, 2 Years Free Update
  • 【Professional Diagnostics】 The VD80 BT Lite bidirectional obd2 scanner is a professional OBD2 scanner diagnostic tool, delivering vehicle diagnostics right in your own garage. It supports 4,000+ active diagnostic tests, 28+ maintenance service functions, ECU coding, PMI calibration, brake service reset, and OEM-grade full-system vehicle scanning—perfect for DIYers and pros looking for powerful automotive tools. The available function tests vary by model—please to confirm compatibility.
  • 【ADVANCED ECU CODE, CUSTOMIZE OE-SETTINGS】As a complete car code reader and reset tool, the VD80 BT Lite bidirectional obd2 scanner supports ECU coding for VWeBay logo, for AudieBay logo, for BMWeBay logo, for Benz, for MitsubishieBay logo and more. PMI function for FordeBay logo/for LincolneBay logo/for MazdaeBay logo, supports copy data into new module. Step-by-step Guided Diagnostics makes complex jobs easier—making this one of the most reliable code readers & scan tools on the market.
  • 【100000+ Vehicles Compatibility – CAN FD/DOIP】 VD80 BT Lite Auto Scanner Compatible with 100,000+ vehicles worldwide, this bidirectiona car scanner works with all OBD2-compliant vehicles manufactured after 1996, covering more than 100 brands worldwide. It also supports CAN FD, DOIP and FCAeBay logo Secure Gateway protocols, boost 2X faster data transfer, covers 99% of U.S., EU and Asian cars. With 22 languages and 2 years of f*ree updates—future-proofing your car reader diagnostic for all cars.
  • 【28+ Maintenance Services & Calibration Functions】VD80 BT Lite scanner for car Supports 28 maintenance services, including resetting oil and service lights after routine maintenance, registering new batteries for proper system operation, and clear clogged filters and restore performance. Additionally, it calibrates TPMS sensors after tire rotations, resets brake systems after pad replacements, relearns steering angle sensors after alignments, and more. These functions help your vehicle quickly and accurately return to peak performance—without the costly dealer visits.
  • 【True Bidirectional Control – Diagnose with Confidence】Standing out with full-system coverage and extensive active test capabilities, the VD80 BT Lite bidirectional scan tool retrieves data from electronic control units and performs a wide range of active tests. You can real-time control over modules like fuel pumps, windows, A/C clutches, and relays. Perform 100+ advanced functions including throttle adaptation, injector coding, VIN write, idle relearn, and ABS bleed—helping you fix it right the first time with this all-in-one car diagnostic scanner.

Last update on 2026-06-23 / Affiliate links / Images from Amazon Product Advertising API


 


This product presentation was made with AAWP plugin.

Share to...