2016

Pre-Delivery Inspection
Technician Reference Document

Effective 7-22-2015-US
Version 1.5

Table
of Contents
A3/S3/A3
TDI
Technician Reference Document
Technician Reference Document Overview
The Pre-Delivery Inspection Technician Reference Document is designed to be a resource used in hand with
the Pre-Delivery Inspection Checklist (PDI). The PDI Checklist has been simplified to make the process more
efficient, and in doing so, this document has been created to be used as a reference for checklist items that
may have additional information. On the PDI Checklist, you find that certain items have been notated with an
asterisk symbol (*), this lets you know that additional information can be found in this Technician Reference
Document.
Below you will find a list of each model, with the page numbers to their left. After navigating to the desired
page, you will notice each model page is formatted similarly to the PDI Checklists. After each section title is the
original checklist item, followed by any additional information specific to that model.

Table of Contents
3-4

A3/S3/A3 TDI

5-6

A3 Cabriolet

7-8

A3 e-tron Sportback

9-10

A4/S4/allroad

11-12

A5/S5/RS 5 Coupe

13-14

A5/S5/RS 5 Cabriolet

15-17

A6/S6/A6 TDI

18-20

A7/S7/A7 TDI

21-23

A8/A8 L/A8 W12/S8/A8 L TDI

24-25

Q3

26-27

Q5/Q5 hybrid/SQ5/Q5 TDI

28-29

TT/TTS Coupe

30-31

TT/TTS Roadster

Effective 7-22-2015-US
Version 1.5

Model Year 2016 | Audi Pre-Delivery Reference Document | 2

A3/S3/A3 TDI
Technician Reference Document
Vehicle Preparation

Interior

• Deactivate vehicle transport mode

• Check operation of window, lock, and seat controls

Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating)
• Set adaption channel to enable CD Ripping (if equipped
with NAV)
Set adaptation channel (via Control Module list –> 5F –>
Guided Functions –> 5F Adaption). Also referred to as CD
Ripping. Perform 3 button reset of the MMI to complete the
activation. Refer to the owners manual for model specific
button sequence
• Set service reminder
via Special functions –> Service work –> 17-PDI-resetting SRI
at PDI, counter reset, etc
• Perform any open campaigns
Follow instructions listed in campaign documentation
Under the Hood Inspection
• Check battery clamps for proper torque
Re-torque if required
• Perform a battery test
Perform a battery test and attach the results to the repair
order
• Check engine oil level
Fill oil to the max level when the vehicle is at operating temperature
Exterior
• Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors
and trunk manually and remotely lock/unlock with all keys,
including all door handle sensors with Advanced Key (if
equipped)
• Test front washers (and headlight washers if equipped)
Headlights must be on to test functionality of the headlight
washers
Trunk Inspection
• Install wheel bolt cover removal tool from PDI kit into
trunk tool kit

Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
• Verify windows can be operated with the key
Verify windows roll down and sunroof opens when either the
key inserted in the door or by holding the unlock button on
the remote
• Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating (if equipped)
• Check rear view mirror operation
Check self-dimming function/lighting (if equipped)
• Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents for all zones
• Inspect operation of all power outlets
Inspect operation of front outlet, USB 5v power jack, and
rear seat outlet
• Check panoramic sunroof operation
Verify open/close/vent/deflector at edge and sunshade
operation
Settings
• Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”
Change time zone appropriate to the dealer location
• Verify and set language and Measurement Units
This can be changed in the Setup/Settings menu
• Verify operation of speech dialogue system (if equipped)
Press the “Talk” button and verify several commands
• Set “Music volume while parking” to 6 lines
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera)
• Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership
during road test

Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit
• Set spare tire pressure
See separate “2016 Normal Load Condition Tire Pressure
Table” posted on ServiceNet
Effective 7-22-2015-US
Version 1.5

Model Year 2016 | Audi Pre-Delivery Reference Document | 3

A3/S3/A3 TDI
Technician Reference Document
Settings (continued)

On-Hoist Inspection (continued)

• Load Onboard Video Tutorials

• Set and store tire pressures for either sold vehicle OR stock
inventory vehicle

Load Onboard Video Tutorials> Turn ignition on> Insert the
Onboard DVD into the DVD Drive> Select the CAR function
button. System will initialize>Select the Owner’s Man.
function by selecting the upper right control button> Select
“Yes”> Select “CD/DVD”> Select “Start update”> Turn off
ignition to start update (the update will take approx. 5 minutes)> Once completed, remove the disk and place back into
the case for the next vehicle

If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2016 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
doorjamb, and store tire pressure values in Car/System menu
Driving Performance

Media / Radio / SAT
• Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
Audi connect (USA ONLY) (if equipped)
• Verify Audi connect Information Packet is present
Verify Audi connect Information Packet is present, including
Audi brochure, AT&T brochure, customer SIM card, AT&T
Terms & Conditions (T&C)(if applicable)
• Connect the dealer demo SIM card to verify system
connects to mobile network
Connect the AT&T dealer demo SIM card to the vehicle and
make sure the system fully connects to the wireless network
(LTE symbol with service bars)(only applies if in an AT&T
service area)

• Verify engine performance and acceleration
Listen for abnormal noise/vibrations
• Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
• Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
Driver Assistance
• Verify operation of parking system (if equipped)
Verify operation of Audi parking system sensors with rear
view camera (if equipped)

• Turn on the wireless network
Ensure the wireless network is turned on (TEL > Settings >
Network connection (Wi-Fi) > select “Visible”)
• Check Wi-Fi hotspot functionality
Check Wi-Fi hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX,” where XXXXX = the last five digits of VIN that are automatically preset in the system
• Enable Google Earth
Enable Google Earth in the navigation settings and verify the
white Google Logo appears next to the LTE, 3G, or 2G symbol
On-Hoist Inspection
• Inspect wheel bolts for proper torque
Use torque wrench to verify
• Install wheel bolt covers and center caps as supplied
Wheel bolt covers and center caps can be found in the PDI kit

Effective 7-22-2015-US
Version 1.5

Model Year 2016 | Audi Pre-Delivery Reference Document | 4

A3 Cabriolet
Technician Reference Document
Vehicle Preparation

Trunk Inspection (continued)

• Deactivate vehicle transport mode

• Set spare tire pressure 1.8T ONLY

Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating)
• Set adaption channel to enable CD Ripping (if equipped
with NAV)
Set adaptation channel (via Control Module list –> 5F –>
Guided Functions –> 5F Adaption). Also referred to as CD
Ripping. Perform 3 button reset of the MMI to complete the
activation. Refer to the owners manual for model specific
button sequence
• Set service reminder
via Special functions –> Service work –> 17-PDI-resetting SRI
at PDI, counter reset, etc
• Perform any open campaigns
Follow instructions listed in campaign documentation
Under the Hood Inspection
• Check battery clamps for proper torque
Re-torque if required
• Perform a battery test
Perform a battery test and attach the results to the repair
order
• Check engine oil level
Fill oil to the max level when the vehicle is at operating temperature
Exterior
• Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors
and trunk manually and remotely lock/unlock with all keys,
including all door handle sensors with Advanced Key (if
equipped)
• Test front washers (and headlight washers if equipped)
Headlights must be on to test functionality of the headlight
washers
Trunk Inspection
• Install wheel bolt cover removal tool from PDI kit into
trunk tool kit
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit

Effective 7-22-2015-US
Version 1.5

For the 1.8T A3 Cab, see separate “2015 Normal Load Condition Tire Pressure Table” posted on ServiceNet for proper
inflation. For the 2.0T A3 Cabriolet, verify the inflatable
spare tire and compressor are present
Interior
• Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
• Verify windows can be operated with the key
Verify windows roll down and sunroof opens when either the
key inserted in the door or by holding the unlock button on
the remote
• Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating (if equipped)
• Check rear view mirror operation
Check self-dimming function/lighting (if equipped)
• Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents for all zones
• Inspect operation of all power outlets
Inspect operation of front outlet, USB 5v power jack, and
rear seat outlet
• Check panoramic sunroof operation
Verify open/close/vent/deflector at edge and sunshade
operation
Settings
• Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”
Change time zone appropriate to the dealer location
• Verify and set language and Measurement Units
This can be changed in the Setup/Settings menu
• Set “Music volume while parking” to 6 lines
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera)
• Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership
during road test

Model Year 2016 | Audi Pre-Delivery Reference Document | 5

A3 Cabriolet
Technician Reference Document
Settings (continued)

On-Hoist Inspection (continued)

• Load Onboard Video Tutorials

• Set and store tire pressures for either sold vehicle OR stock
inventory vehicle

Load Onboard Video Tutorials> Turn ignition on> Insert the
Onboard DVD into the DVD Drive> Select the CAR function
button. System will initialize>Select the Owner’s Man.
function by selecting the upper right control button> Select
“Yes”> Select “CD/DVD”> Select “Start update”> Turn off
ignition to start update (the update will take approx. 5 minutes)> Once completed, remove the disk and place back into
the case for the next vehicle

If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2016 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
doorjamb, and store tire pressure values in Car/System menu
Driving Performance

Media / Radio / SAT
• Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
Audi connect (USA ONLY) (if equipped)
• Verify Audi connect Information Packet is present
Verify Audi connect Information Packet is present, including
Audi brochure, AT&T brochure, customer SIM card, AT&T
Terms & Conditions (T&C)(if applicable)
• Connect the dealer demo SIM card to verify system
connects to mobile network
Connect the AT&T dealer demo SIM card to the vehicle and
make sure the system fully connects to the wireless network
(LTE symbol with service bars)(only applies if in an AT&T
service area)
• Turn on the wireless network
Ensure the wireless network is turned on (TEL > Settings >
Network connection (Wi-Fi) > select “Visible”)

• Verify engine performance and acceleration
Listen for abnormal noise/vibrations
• Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
• Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
Driver Assistance
• Verify operation of parking system (if equipped)
Verify operation of Audi parking system sensors with rear
view camera (if equipped)
Convertible Functionality (if equipped)
• Test operation of power folding top
Perform with engine running to conserve battery power

• Check Wi-Fi hotspot functionality
Check Wi-Fi hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX,” where XXXXX = the last five digits of VIN that are automatically preset in the system
• Enable Google Earth
Enable Google Earth in the navigation settings and verify the
white Google Logo appears next to the LTE, 3G, or 2G symbol
On-Hoist Inspection
• Inspect wheel bolts for proper torque
Use torque wrench to verify
• Install wheel bolt covers and center caps as supplied
Wheel bolt covers and center caps can be found in the PDI kit

Effective 7-22-2015-US
Version 1.5

Model Year 2016 | Audi Pre-Delivery Reference Document | 6

A3 e-tron Sportback
Technician Reference Document
Vehicle Preparation

Interior

• Deactivate vehicle transport mode

• Check operation of window, lock, and seat controls

Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating)
• Set adaption channel to enable CD Ripping (if equipped
with NAV)
Set adaptation channel (via Control Module list –> 5F –>
Guided Functions –> 5F Adaption). Also referred to as CD
Ripping. Perform 3 button reset of the MMI to complete the
activation. Refer to the owners manual for model specific
button sequence
• Set service reminder
via Special functions –> Service work –> 17-PDI-resetting SRI
at PDI, counter reset, etc
• Perform any open campaigns
Follow instructions listed in campaign documentation
Under the Hood Inspection
• Check battery clamps for proper torque
Re-torque if required
• Perform a battery test
Perform a battery test and attach the results to the repair
order
• Check engine oil level
Fill oil to the max level when the vehicle is at operating temperature
Exterior
• Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors
and trunk manually and remotely lock/unlock with all keys,
including all door handle sensors with Advanced Key (if
equipped)
• Test front washers (and headlight washers if equipped)
Headlights must be on to test functionality of the headlight
washers
Trunk Inspection
• Install wheel bolt cover removal tool from PDI kit into
trunk lid toolkit

Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
• Verify windows can be operated with the key
Verify windows roll down and sunroof opens when either the
key inserted in the door or by holding the unlock button on
the remote
• Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating (if equipped)
• Check rear view mirror operation
Check self-dimming function/lighting (if equipped)
• Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents for all zones
• Inspect operation of all power outlets
Inspect operation of front outlet, USB 5v power jack, and
rear seat outlet
• Check panoramic sunroof operation
Verify open/close/vent/deflector at edge and sunshade
operation
Settings
• Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”
Change time zone appropriate to the dealer location
• Verify and set language and Measurement Units
This can be changed in the Setup/Settings menu
• Verify operation of speech dialogue system (if equipped)
Press the “Talk” button and verify several commands
• Set “Music volume while parking” to 6 lines
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera)
• Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership
during road test

Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit

Effective 7-22-2015-US
Version 1.5

Model Year 2016 | Audi Pre-Delivery Reference Document | 7

A3 e-tron Sportback
Technician Reference Document
Settings (continued)

On-Hoist Inspection (continued)

• Load Onboard Video Tutorials

• Set and store tire pressures for either sold vehicle OR stock
inventory vehicle

Load Onboard Video Tutorials> Turn ignition on> Insert the
Onboard DVD into the DVD Drive> Select the CAR function
button. System will initialize>Select the Owner’s Man.
function by selecting the upper right control button> Select
“Yes”> Select “CD/DVD”> Select “Start update”> Turn off
ignition to start update (the update will take approx. 5 minutes)> Once completed, remove the disk and place back into
the case for the next vehicle
Media / Radio / SAT
• Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
Audi connect (USA ONLY) (if equipped)
Verify Audi connect Information Packet is present, including
Audi brochure, AT&T brochure, customer SIM card, AT&T
Terms & Conditions (T&C)(if applicable)
• Connect the dealer demo SIM card to verify system
connects to mobile network
Connect the AT&T dealer demo SIM card to the vehicle and
make sure the system fully connects to the wireless network
(LTE symbol with service bars)(only applies if in an AT&T
service area)

If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2016 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
doorjamb, and store tire pressure values in Car/System menu
Driving Performance
• Verify engine performance and acceleration
Listen for abnormal noise/vibrations
• Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
• Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
Driver Assistance
• Verify operation of parking system (if equipped)
Verify operation of Audi parking system sensors with rear
view camera (if equipped)

• Turn on the wireless network
Ensure the wireless network is turned on (TEL > Settings >
Network connection (Wi-Fi) > select “Visible”)
• Check Wi-Fi hotspot functionality
Check Wi-Fi hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX,” where XXXXX = the last five digits of VIN that are automatically preset in the system
• Enable Google Earth
Enable Google Earth in the navigation settings and verify the
white Google Logo appears next to the LTE, 3G, or 2G symbol

Hybrid Technology
• Verify EV button is operating
Push the EV button at a speed below 80 mph and check for
lights on EV button and instrument cluster. Cycle through
the different EV modes: EV, Hybrid, Hold Battery, and Charge
Battery. These settings can be accessed through the MMI
via MENU > Car > Car systems > Charging & e-tron > e-tron
mode. EV mode may or may not activate based on current
operational criteria as described in the owner’s manual
• Verify charging while braking in recuperation range

On-Hoist Inspection
• Inspect wheel bolts for proper torque
Use torque wrench to verify
• Install wheel bolt covers and center caps as supplied
Wheel bolt covers and center caps can be found in the PDI kit

See power meter for details. Will only recuperate if battery is
not fully charged
• Check MMI and instrument cluster for proper operation
mode indication (only shows in MMI if equipped with NAV)
Verify green arrows while EV or electrical drive, orange
while combustion engine active, etc. Only shows in MMI if
equipped with NAV
• Verify front charge port is operational
Plug in charger and verify that it is operational and charges
the vehicle

Effective 7-22-2015-US
Version 1.5

Model Year 2016 | Audi Pre-Delivery Reference Document | 8

A4/S4/allroad
Technician Reference Document
Vehicle Preparation