Detroit Assurance Lane Departure Warning Camera
Installation
FLA COE
FLB COE
FLD Conventional
Business Class
FLC 112 Conventional

Century Class Conventional
Argosy COE
Cargo
Columbia

122SD and Coronado
Business Class M2
> Cascadia
108SD/114SD

54-291
Freightliner
Service Bulletin

Description of Revisions: This bulletin replaces the version dated
July 2015. Figure 1 is added to show the camera mounting
training aid provided by "DTNA Custom Built Training Aids" which
can be used as an alternative to the mounting template described
in this bulletin.

General Information
Use the instructions in this bulletin to replace the Detroit Assurance Lane Departure Warning (LDW) camera.

Parts
Refer to Table 1 for camera cover and base part numbers.
Camera Mounting Assembly Parts
Description
Part Number
Cover – Camera, Global Radar
18-67468-000
Cover – Camera Base, Global Radar
A18-67911-000
Table 1, Camera Mounting Assembly Parts

NOTE: A camera mounting training aid has been designed by "DTNA Custom Built Training Aids" and
is available through the Aftermarket Resource Center (ARC) website. See Fig. 1. The training aid can
be used as an alternative to the mounting procedure described in this bulletin. The order form for the
tool can be accessed by clicking the "Training Aids" link located on the lower right-hand side of ARC’s
home page, then clicking "Detroit Camera Mounting Tool Order Form" on the right-hand side of the
page. It is still necessary to order the camera mounting assembly parts described in Table 1 before
the camera can be mounted using this tool.

Installing the Detroit LDW Camera
1. Park the vehicle and apply the parking brakes.
2. Run the engine until the air system is fully charged, then shut down the engine and chock the tires.

IMPORTANT: Completely clean the area where the camera will be mounted. If the windshield is not
clean and free of grease and dust, the camera may not properly adhere to the windshield surface.
3. Clean the windshield mounting surface with IPA wipe (50/50 mix of isopropyl alcohol and water) or
equivalent cleaner. Use a clean towel, and make sure the windshield surface is completely clean and free of
grease and dust.
4. Create the template included with this bulletin.

IMPORTANT: When printing the template, make sure that the "Actual Size" radio button is
selected under the "Size" tab, the "Auto portrait/landscape" radio button is selected under the
"Orientation" heading, and that the "1-sided" radio button is selected on the properties screen.
See Fig. 2 and Fig. 3.
4.1

Print the template provided on the last page of this bulletin.

Freightliner Service Bulletin, September 2015

Page 1

Detroit Assurance Lane Departure Warning Camera
Installation

54-291
Freightliner
Service Bulletin

FLA COE
FLB COE
FLD Conventional
Business Class
FLC 112 Conventional

Century Class Conventional
Argosy COE
Cargo
Columbia

122SD and Coronado
Business Class M2
> Cascadia
108SD/114SD

2
1

A

09/10/2015

3

f670151

A. The training aid is used to position the camera
base on the windshield.
1. Camera Base
2. Windshield
3. Camera Mounting Training Aid
Fig. 1, Camera Mounting Training Aid

4.2

Using a ruler, verify the length of the printed ruler graphic on the template. If the length of the ruler
graphic does not measure accurately, the template did not scale properly. Repeat this step until the
markings on the printed ruler match those of the ruler in hand.

4.3

Secure the template to a piece of thick cardboard with glue or tape. See Fig. 4.

4.4

Cut along the border, through the template and the cardboard, using a razor knife and straight edge.
See Fig. 5. Verify the dimensions shown on the template.

5. Using a digital level, take a level reading of the surface where the vehicle is parked. See Fig. 6.
6. Position the template on the passenger-side windshield, so the left edge is against the center rubber seal
and the top edge sits against the windshield upper rubber seal, then tape the template to the windshield.

IMPORTANT: Do not re-use the camera base. If the windshield is being replaced, or other service is
performed that requires the removal of the camera base, a new camera base must be installed.
7. Remove the protective liner from the back of the camera base.
8. Install the camera base on the windshield.
8.1

Page 2

Hold the digital level used in step 5 up to the tabs on the camera base. While holding the digital
level on the base, hold the bottom of the camera base away from the windshield glass and align the
top of the camera base with the template. While maintaining zero level, lower the bottom of the
camera base until it contacts the windshield. See Fig. 7.

Freightliner Service Bulletin, September 2015

Detroit Assurance Lane Departure Warning Camera
Installation
FLA COE
FLB COE
FLD Conventional
Business Class
FLC 112 Conventional

Century Class Conventional
Argosy COE
Cargo
Columbia

54-291
Freightliner
Service Bulletin

122SD and Coronado
Business Class M2
> Cascadia
108SD/114SD

1

2
1

3
4

04/15/2015

f120335

1. 1-sided Radio Button
04/24/2015

1.
2.
3.
4.

f120336

Properties Button
Size Tab
"Actual Size" Radio Button
"Auto Portrait/Landscape" Radio Button

Fig. 3, Document Properties Screen

Fig. 2, Print Screen

8.2

Verify proper alignment of the camera base using the dimensions shown in Fig. 8. Hold the digital
up to the tabs on the camera base. See Fig. 9. The level reading should be the same as the
reading taken of the surface where the vehicle is parked (±0.4 degrees, with a maximum spec of
±1.5 degrees). If the base is aligned correctly, continue with step 9. If the base is not aligned
correctly, remove it immediately before it cures and repeat steps 8.1 and 8.2.

9. Apply pressure on the base for 30 seconds, then wait 15–30 minutes for the camera base adhesive to set.
10. Connect the camera to the VRDU (Video Radar Detection Unit).
11. Fit the top of the camera into the two tabs on the camera base. See Fig. 10.

IMPORTANT: Take care when snapping the camera into the lower mounting notch. If the notch is
damaged, the camera base must be replaced.
12. Tilt the bottom of the camera forward until it snaps into the lower mounting notch. See Fig. 11.
13. Attach the camera cover to the base by first aligning the bottom mounting tabs then gently rotating the
cover upwards, taking care to position the connector cable so that it feeds through the opening at the top of
the cover.

Warranty
This is an informational bulletin only. Warranty does not apply.

Freightliner Service Bulletin, September 2015

Page 3

54-291
Freightliner
Service Bulletin

Detroit Assurance Lane Departure Warning Camera
Installation
FLA COE
FLB COE
FLD Conventional
Business Class
FLC 112 Conventional

Century Class Conventional
Argosy COE
Cargo
Columbia

04/13/2015

122SD and Coronado
Business Class M2
> Cascadia
108SD/114SD

f546164

Fig. 4, Template Taped to Cardboard

Page 4

Freightliner Service Bulletin, September 2015

Detroit Assurance Lane Departure Warning Camera
Installation
FLA COE
FLB COE
FLD Conventional
Business Class
FLC 112 Conventional

Century Class Conventional
Argosy COE
Cargo
Columbia

54-291
Freightliner
Service Bulletin

122SD and Coronado
Business Class M2
> Cascadia
108SD/114SD

04/13/2015

f546165

Fig. 5, Template Cut with a Razor Knife

01/17/2013

f545981

Fig. 6, Measuring the Level on the Surface where the
Vehicle is Parked

Freightliner Service Bulletin, September 2015

Page 5

Detroit Assurance Lane Departure Warning Camera
Installation

54-291
Freightliner
Service Bulletin

FLA COE
FLB COE
FLD Conventional
Business Class
FLC 112 Conventional

1

2

Century Class Conventional
Argosy COE
Cargo
Columbia

122SD and Coronado
Business Class M2
> Cascadia
108SD/114SD

3

04/13/2015

1. Windshield Centerline

f546166

2. Mounting Template

3. Camera Base

Fig. 7, Mounting the Camera Base using the Template

Page 6

Freightliner Service Bulletin, September 2015

Detroit Assurance Lane Departure Warning Camera
Installation
FLA COE
FLB COE
FLD Conventional
Business Class
FLC 112 Conventional

Century Class Conventional
Argosy COE
Cargo
Columbia

122SD and Coronado
Business Class M2
> Cascadia
108SD/114SD

Freightliner
Service Bulletin

2

B

6

54-291

1
3

A
5

5

4
2

3
1

04/13/2015

04/09/2015
f546163

A. Horizontal orientation is 4.7 ±0.2 inches (120 ±5
mm) from the right edge of the windshield
centerline to the edge of the camera base.
B. Vertical orientation is 1.3 ±0.2 inches (33 ±5 mm)
from the top of the camera base to the bottom
edge of the windshield rubber seal.
1. Lower Mounting Notch
2. Windshield Centerline
3. LDW Camera
4. Camera Base
5. Camera Mounting Tabs
6. Windshield Rubber Seal

f546156

1. Template
2. Camera Base
3. Digital Level
Fig. 9, Aligning the Base with a Digital Level

Fig. 8, Installing the Camera Base

Freightliner Service Bulletin, September 2015

Page 7

Detroit Assurance Lane Departure Warning Camera
Installation

54-291
Freightliner
Service Bulletin

FLA COE
FLB COE
FLD Conventional
Business Class
FLC 112 Conventional

Century Class Conventional
Argosy COE
Cargo
Columbia

122SD and Coronado
Business Class M2
> Cascadia
108SD/114SD

1

1

2

3

04/09/2015

f546154

1. Tabs
Fig. 10, Camera Base Tabs

04/09/2015

f546155

1. Base Mounting Tabs
2. LDW Camera
3. VRDU Connector
Fig. 11, LDW Camera Installed

Page 8

Freightliner Service Bulletin, September 2015

Inches

1

0

10

20

2

30
40 50
Millimeters

4

3

60

70

80

90

100