Technical Bulletin
Model(s)

Year

Golf, Jetta, Jetta
SportWagen

2009-2012

Eng. Code

Trans. Code

VIN Range From

VIN Range To

All

All

All

2.0L TDI
(CBEA, CJAA)

Condition
23 15 03 June 24, 2015 2041063
MIL ON, No Start, or Rough Running with DTCs P0087, P0088 or P0191 Stored in ECM Fault Memory (TDI
ONLY)
MIL ON, No Start, or Rough Running with one or more of the following DTCs Stored in ECM Fault Memory:

DTC

Description

P0087

Fuel Rail/System Pressure - Too Low

P0088

Fuel Rail/System Pressure - Too High

P0191

Fuel Rail Pressure Sensor "A" Circuit
Range/Performance

Technical Background
When diagnosing the condition above on a common rail diesel vehicle, if no root cause is found after checking all
other components and all GFF diagnostic procedures have been performed, it may be necessary to check for
metallic particles in the High Pressure Fuel Pump using the service section of this bulletin.
If such an inspection is necessary, the following guidelines must be observed when removing the N290 Fuel
Metering Valve.

Production Solution
No production change required.

Page 1 of 13
© 2015 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Technical Bulletin
Service

Note:
Inspect the fuel filler neck for a properly installed and
functioning misfueling guard (see figure 1). Refer to
Warranty Bulletin VWP-15-06 for details regarding HPFP
coverage eligibility.

Figure 1. Misfueling guard installed in the filler
neck.

Section A – Initial Diagnosis of the High Pressure Fuel Pump (HPFP)
Note:
Removing the N290 Fuel Metering Valve to inspect for metallic particles should only be considered as a last step
after all GFF diagnostic procedures have been performed. This includes testing supply pressure to the high
pressure fuel pump (low pressure side), and checking for internal leakage from the injectors and the N276
Pressure Regulating Valve.

Page 2 of 13
© 2015 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Technical Bulletin
Note:
Prior to removing the N290 Fuel Metering Valve, the
area surrounding the valve (Figure 2) must be clean and
dried with compressed air to remove ALL debris from the
area. See Repair Manual Group 20 Fuel Supply, General
Information, Clean Working Conditions in Elsa.
If debris enters the fuel system, components may be
damaged.

Figure 2. Surrounding Area

1. Remove the N290 Fuel Metering Valve and inspect
the valve and valve bore for the presence of metallic
particles (see Figure 3).

Figure 3. N290 Fuel Metering Valve and Valve Bore

2. If metallic particles are found on the N290 Fuel Metering Valve or in the valve bore, replacement of the high
pressure fuel pump and major components in the fuel system is necessary. Proceed to Section B – Fuel
Sampling and Analysis.
3. If no metallic particles are found on the N290 Fuel Metering Valve or in the valve bore, do not replace the high
pressure fuel pump. Open a VTA case and contact the Volkswagen Technician’s Helpline for further assistance
diagnosing the vehicle, this bulletin does not apply.

Page 3 of 13
© 2015 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Technical Bulletin
Note:
To prevent fuel system damage, ensure that the N290
Fuel Metering Valve is free of any contaminates before
reinstalling.
Prior to reinstallation of the N290 Fuel Metering Valve,
ensure that both O-rings are not damaged. If they are
damaged, the high pressure fuel pump must be replaced.
To prevent damaging the O-rings when reinstalling the
N290 Fuel Metering Valve, lubricate the O-rings with diesel
fuel (see Figure 4).

Figure 4. N290 Fuel Metering Valve O-rings
4. Install the N290 Fuel Metering Valve into the valve bore using light pressure.
5. Install and hand tighten both M5 fasteners, ensuring that the threads are clean and dry.
Pre-tighten to 2 Nm, then to 6.5 – 7 Nm.
6. If metallic particles are found on the N290 Fuel Metering Valve or in the valve bore (see figure 3), replacement
of the high pressure fuel pump and major components of the fuel system are necessary.

Section B – Fuel Sampling and Analysis

Note:
A fuel sample must be taken and analyzed prior to repairing the vehicle.
1. The fuel sample kit, P/N LQ1LKIT must be ordered via the Compliance Label Ordering Portal in vwhub.com fuel
sample kit will be sent to the dealership within 1 business day*.

Page 4 of 13
© 2015 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Technical Bulletin
The Compliance Label Ordering Portal is
available through the Service or Parts tab in
VWHub.com

Figure 5. Compliance Label Ordering

Enter the VIN in the Quick VIN Order field.

Figure 6. Enter VIN

Figure 7. Select part number LQ1LKIT
Tip:
When ordering LQ1LKIT on the Compliance Label Ordering Portal, please include a secondary email address (ie.
service manager) in the purchase order field for dealer e-mail notification.
2. Each fuel sample kit will contain the prepaid shipping label, detailed packaging instructions, and all necessary
packaging to send the fuel sample via FedEx ground to a designated test facility.

Page 5 of 13
© 2015 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Technical Bulletin
Note:
HAZMAT certification is required for packaging the fuel sample but NOT for shipping *. The diesel fuel sample
may be shipped to the laboratory utilizing ground shipment services provided the dealer is using the Limited
Quantity Kit (PN# LQ1LKIT).
3. The fuel analysis results will be available to the dealership within 3 to 5 business days once the fuel sample has
been shipped to the laboratory. The dealer will be notified via an email to acquire a pdf copy of the analysis result
certificate via an embedded link to VW Google Search. The dealer enters the VIN and the report is presented
under the heading "Component Locations, Wiring Diagrams, and Share Folders" in the lower right hand corner of
the search results screen.
4. Once the test results are obtained by the dealership, they will be clearly marked “PASS” or “FAIL” in the
comments section (see figures 7 and 8).
5. Refer to Warranty Bulletin VWP-15-06 for details regarding HPFP coverage eligibility.

Fuel Sample Analysis Results
If the fuel sample Certificate of Analysis indicates “PASS”: Sections A & B & C will be reimbursed under warranty.
If the fuel sample Certificate of Analysis indicates “FAIL”: Only sections A & B will be reimbursed under warranty.

6. When the fuel analysis process is complete, proceed to Section C – High Pressure Fuel Pump Replacement
and Fuel System Repair.
*Hawaii, Alaska, Puerto Rico: Please follow step one. Once a fuel sample is ordered, you will be contacted by a
Volkswagen of America representative who will provide further instructions. A third party will be used to package
and ship your fuel samples to the laboratory.
Note:
Each Certificate of Analysis will contain a “Pass” or
“Fail” comment as shown.

Figure 7. Example of a clean fuel sample analysis.
Page 6 of 13
© 2015 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Technical Bulletin

Figure 8. Example of a contaminated fuel analysis.

Section C – High Pressure Fuel Pump Replacement and Fuel System Repair
1. Always use the latest information in Elsa for detailed removal and replacement instructions of the components
listed in this technical bulletin.
2. Remove in-tank fuel pump (Sending unit).
3. Drain and clean the fuel tank using the suction pump VAS5226.
4. Fill the fuel tank with (1.3 gallons) of fresh diesel fuel.
5. Drain and clean the tank completely using VAS5226.
6. Replace the in-tank fuel pump (Sending unit).
7. Flush the fuel lines (both feed and return) from the fuel tank to the bulk head, using either mineral spirits or
brake clean with compressed air. Alternate from both ends of the lines while using a shop towel to catch any
debris that may still be in the line. Verify all metal is removed from both lines before proceeding.
8. Replace the following components as per Elsa: high pressure fuel pump, high pressure fuel lines, fuel rail (with
both sensors included), all fuel injectors, fuel return lines (overflow lines), fuel filter, fuel filter housing, auxiliary fuel
pump.
Note:
The rubber fuel line insulators from the original injector supply lines should be transferred to the new lines.
9. Once repairs are complete fuel the vehicle.
10. Ensure the fuel injector return lines are properly seated and sealed once it is installed.

Page 7 of 13
© 2015 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Technical Bulletin
Note:
The “injector quantity calibration” and the “injector voltage calibration” for the new injectors must be programmed
into the Engine Control Module -J623- after replacing one or more injectors. Refer to “Guided Functions” in the
vehicle diagnostic tester.
11. Using the VAS tester, perform the guided function “Vent Fuel System”. (see Elsa for additional information
under “Fuel System, Filling and Bleeding”).
Note:
If the test plan is unavailable through Guided Functions, switch to Self Diagnosis>Engine Electronics>Basic
Settings>35 and perform the basic settings 3 times consecutively. For UDS vehices, perform basic settings for
initial fueling.
12. Once the repairs are complete, test drive the vehicle.
13. Inspect for fuel seepage at the fuel injector return line connector. If seepage is found the condition MUST be
corrected.

Warranty
Reimbursement for Sections A & B Only Where Fuel Analysis Result = FAIL

Note:
Active VW Customer Mobility Program (VWCMP) loaner vehicles are eligible to receive $35 per day for
loaner expense reimbursement under this warranty extension. For dealers enrolled in the VWCMP, a nonVWCMP loaner vehicle can be provided at a reimbursement rate of $25 per day or a VW rental at $35 if a
VWCMP loaner is not available. These claims must be submitted in SAGA on a separate line using claim
type 1SP. Refer to document VWS-14-03 for applicable labor operation.

To determine if this procedure is covered under Warranty, always refer to the Warranty Policies and
Procedures Manual 1)
Model(s)

Year(s)

Golf, Jetta,
Jetta
SportWagen

2009-2012

Eng. Code(s)

Trans. Code(s)

VIN Range From

VIN Range To

All

All

All

2.0L TDI
(CBEA, CJAA)
Page 8 of 13

© 2015 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Technical Bulletin
SAGA Coding
Claim Type:

Use applicable Claim Type 1)
Damage

Service Number:

HST

Damage Location (Depends on
Service No.)

--

Use applicable when indicated
in Elsa (L/R)

Code
2374

0010

Parts Manufacturer

Golf, Jetta, Jetta Wagon, Jetta
SportWagen

Causal Part: Select Labor Operation

01320000

Outside Material: Diesel Fuel

Part Number: FUEL

3ME 2)

Diagnostic Time 4)
GFF Time expenditure

01500000 = As required

Road Test

01210002 = 00 TU

YES
NO

01210004 = 00 TU
Technical Diagnosis

01320000 = As required

YES

Claim Comment: Input “As per Technical Bulletin 2041063” in comment section of Warranty Claim.
1)

Vehicle may be outside any Warranty in which case this Technical Bulletin is informational only

2)

Code per warranty vendor code policy.

3)

Labor Time Units (TUs) are subject to change with ELSA updates.

4)

Documentation required per Warranty Policies and Procedures Manual.

Page 9 of 13
© 2015 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Technical Bulletin
Note:
Vendor code BPY or BPT must be recorded from the original High Pressure Fuel Pump for claiming purposes.

Reimbursement for Sections A & B & C Where Fuel Analysis Results = PASS

Note:
Active VW Customer Mobility Program (VWCMP) loaner vehicles are eligible to receive $35 per day for
loaner expense reimbursement under this warranty extension. For dealers enrolled in the VWCMP, a nonVWCMP loaner vehicle can be provided at a reimbursement rate of $25 per day or a VW rental at $35 if a
VWCMP loaner is not available. These claims must be submitted in SAGA on a separate line using claim
type 1SP. Refer to document VWS-14-03 for applicable labor operation.

To determine if this procedure is covered under Warranty, always refer to the Warranty Policies and
Procedures Manual 1)
Model(s)