PERFECT DELIVERY INSPECTION (PDI)

2015

Q5/Q5 hybrid/SQ5/Q5 TDI

Audi Technician
Report

Stock No.

Dealer Number

R.O. No.

VIN

Road test mileage out

Road test mileage in

All items must be completed prior to customer delivery by an Audi
technician (for Audi Q5 hybrid, only “Hybrid Aware” techs are able
to PDI the hybrid)
*Refer to the Special functions tab of ODIS Diagnosis using GFF
for the PDI function tests

Trunk Inspection
 Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit behind spare tire.
Please note that in the hybrid it is located on the luggage
floor on the right side

**Audi recommends using an Audi approved battery charger to
prevent excessive battery discharge during inspection

 Verify operation of luggage cover

Open Campaigns/Updates

Exterior

 Check Elsa for open campaigns and updates. Perform
campaigns not requiring SVM if applicable. Campaigns
requiring SVM should only be performed after the vehicle has
been taken out of transport mode

 Test windshield washers (front and rear) for aim and function

Battery Inspection
 Check battery clamps for proper torque. Re-torque if required

 Turn on headlights and test headlamp washers (if equipped)
 Test exterior lighting functions
 Install the rubber strips to the top of the base carrier bars (do
not install the carrier bars on the vehicle unless customer has
requested). Repackage the bars into the box if they are not
being installed on the vehicle

 Perform the A-battery test for new batteries using GFF in ODIS
Diagnosis –> Special functions –>Service work. Select option 2, the
battery test for new batteries as part of the pre–delivery
inspection and act according to the test result (ok, recharge,
replace). Ensure diagnosis log is uploaded to the GFF paperless
server by selecting “ok” when tester wants to send the current
generated diagnosis protocol online. (Note: Do not use Guided
Function. The diagnosis log will not be uploaded to GFF paperless)

 Retrieve the paper with the torque wrench key code from the
base carrier bar box. Insert the paper with the key code into the
owner’s literature wallet. Record torque wrench key code in the
VDF to ensure it’s documented in the event the paper with the
code is misplaced

Transport Mode Deactivation, DTC check, set service reminder
*It is advised to start ODIS with the engine running to enable all
5F Test Plans in GFF and also to ensure SVM sees all control units
during the SVM check vehicle configuration

 Adjust the trunk lid opening height to 75 inches (190 cm) from
the ground to the close button in the rear lid. Press and hold
the close button in the rear lid for at least four seconds to
program the opening height

 Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating )

Interior

 Set service reminder (via Special functions –> Service work –>
17-PDI-resetting SRI at PDI, counter reset, etc.)

 Check operation of all switches: Locks, windows, seat adjustment, seat heating (if equipped) and child safety features

 For MMI3G+ vehicles, set adaptation channel (via Special
functions –> Service work –> : 5F–Activating/deactivating
storage of music). Also referred to as CD Ripping. Perform hard
reset of the MMI to complete the activation

 Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)

 Perform any campaign update requiring SVM at this time
(follow instructions listed in campaign documentation)
Under the Hood Fluid Check and Inspection
 Check all fluid levels and top off if necessary
 Check engine oil level using Special Tool T40178 on a flat and
level surface
Effective 7-7-2014-US
Version 1.2

 Check key functionality, including seat memory (if equipped);
verify vehicle starts and runs with the start/stop button; verify
all doors lock/unlock with remote and advanced key, including
all door handle sensors with the advanced key (if equipped)

 Verify operation of all interior lights
 Mirrors: Inspect folding, adjustments, RH tilt in reverse, and
memory (if equipped)
 Inspect operation of lighter, aux. outlet under armrest, and
rear outlet and cargo area (if equipped)
 Verify operation of all front and rear seat belts and latches
 Check horn operation
 Check sunroof and sunshade operation (open/close/vent/
deflector at edge)
1 of 3

PERFECT DELIVERY INSPECTION (PDI)

2015 Q5/Q5 hybrid/SQ5/Q5 TDI | Audi Technician Report

Interior (continued)

Audi connect (if equipped) (USA ONLY)

 Passenger side airbag: Verify operation of Passenger Occupant
Detection System

 Verify Audi connect Information Packet is present, including
Audi brochure, T-Mobile brochure, customer SIM card, T-Mobile
Terms & Conditions (T&C) (if applicable)

 Start-Stop-System info (if applicable): Verify the velum sticker
is on the start/stop button. Remove the Start-Stop-System
information card from the car kit and place it in the glove box
with the owner’s manuals. Additional supply can be ordered via
the Brand Store on AccessAudi
Radio
 Verify operation of CD player
 Verify operation of AMI or aux. input (if equipped)
 SD card slot: Insert SD card and test function (Test all SD card
slots as equipped)

 Connect the dealer demo SIM card to the vehicle and make
sure the system fully connects to 2G or 3G (2G or 3G symbol
with Box surrounding it)(only applies if in a T-Mobile service
area)
 Enable Google Earth in the navigation settings and verify the
white Google Logo appears next to the 2G or 3G symbol
 Ensure the wireless network is turned on (TEL function button
> Settings Ctrl button > Wi-Fi settings > Wi-Fi active > select
“Visible”)

 Verify HD Radio is turned “off” in Radio/Settings Menu

 Check Wi-Fi hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX,” where XXXXX = the last five digits
of VIN that are automatically preset in the system.

Audi MMI/Navigation

On-Hoist Inspection

 Verify and set Language and Measurement Units in Setup Menu

 Check underside of vehicle for fluid leaks and loose components

 Set Time source setting to “GPS” and set Auto daylight savings
time to “on.” Change time zone appropriate to the dealer
location

 Check steering, boots, brake system, hoses, tires and wheels
for damage

 Navigation (if equipped): Set dealership location (for following
back to dealership during road test)

 Inspect wheel bolts for proper torque using torque wrench

 Set the “Music volume while parking” to 6 lines (accessed via
MMI rear view camera display: Settings > Music volume while
parking) (applies to vehicles with park assist or rear view
camera)
 Voice Activation (if equipped): Press the “Talk” button and
verify several Commands
Onboard Video Tutorials
 Load Onboard Video Tutorials

 Remove transport suspension blocks (if installed)
 Install wheel bolt covers and center caps as supplied
 If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2015 Normal Load Condition Tire Pressure
Table” posted on ServiceNet. If going to stock, set to maximum
recommended tire pressures listed on the B-pillar doorjamb,
and store tire pressure values in Car/System menu
Road Test
 Check for squeaks, rattles and wind noise

 Turn ignition on

 Verify operation of Audi parking system plus with rear view
camera (if equipped)

 Insert the Onboard DVD into the DVD Drive

 Verify engine performance and acceleration

 Select the CAR function button. System will initialize

 EV button: Push the EV button at a speed below 65 mph and
check for lights on EV button and instrument cluster. EV mode
may or may not activate based on current operational criteria
as described in the owner’s manual

 Select the Owner’s Man. function by selecting the upper right
control button
 Select “Yes”
 Select “Start update”

 Check MMI and instrument cluster for proper operation mode
indication (green lights while EV or electrical drive, orange
while combustion engine active, etc.)

 Turn off ignition to start update (the update will take approx. 5
minutes)

 Check for state of charging increasing while braking within
recuperation range (see power meter for details)

 Once completed, remove the disk and place back into the case
for the next vehicle

 Verify transmission operation, including shift paddles (if
equipped)

 Select “CD/DVD”

 Check steering/tire alignment

Effective 7-7-2014-US
Version 1.2

2 of 3

PERFECT DELIVERY INSPECTION (PDI)

2015 Q5/Q5 hybrid/SQ5/Q5 TDI | Audi Technician Report

Road Test (continued)

Post-Road Test Inspection

 Test drive vehicle applying brakes several times (at least 4
times) at 20 mph (32 km/h) to clean brake rotors. Check for
abnormal noise/vibration/pulsation

 Interrogate fault memory using the Scan Tool and print
Diagnostic Log

 Parking brake: Apply and verify hold and release
 Verify quality of radio reception in AM/FM/SAT bands

 Record final mileage on checklist and sign checklist
 Ensure the yellow tire pressure tag is installed on steering
wheel

 Verify cruise control/ACC (if equipped) functions
 Verify Audi side assist functionality (if equipped)

Showroom Display/Inventory Storage/Demo Vehicle

 Climate control: Check all functions and ensure proper A/C
cooling

 Install showroom charger to ensure battery remains charged at
all times

 Seat heating/ventilation (if equipped): Inspect for proper
operation

 Apply Inventory Maintenance Sticker
 Install standard wiper blades (if not already installed)

 Navigation function (if equipped): Activate NAV and follow
directions back to dealership
Technician
I certify that all operations have been completed and this vehicle has been prepared in accordance with Audi Procedures and
Quality Standards, and has met the standards for Perfect Delivery.
Last 8 of VIN

Effective 7-7-2014-US
Version 1.2

Technician Signature

Completion Date

3 of 3