PERFECT DELIVERY INSPECTION (PDI)

2015

Q3

Audi Technician Report

Stock No.

Dealer Number

R.O. No.

VIN

Road test mileage out

Road test mileage in

All items must be completed prior to customer delivery by an Audi
technician
*Refer to the Special functions tab of ODIS Diagnosis using GFF
for the PDI function tests

Under the Hood Fluid Check and Inspection (continued)
 Check engine oil level using Special Tool T40178 on a flat and
level surface

**Audi recommends using an Audi approved battery charger to
prevent excessive battery discharge during inspection

Trunk Inspection

Open Campaigns/Updates

 Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit to the right of the
spare tire.

 Check Elsa for open campaigns and updates. Perform
campaigns not requiring SVM if applicable. Campaigns
requiring SVM should only be performed after the vehicle has
been taken out of transport mode
Battery Inspection
 Check battery clamps for proper torque. Re-torque if required
 Perform the A-battery test for new batteries using GFF in ODIS
Diagnosis –> Special functions –>Service work. Select option 2, the
battery test for new batteries as part of the pre–delivery
inspection and act according to the test result (ok, recharge,
replace). Ensure diagnosis log is uploaded to the GFF paperless
server by selecting “ok” when tester wants to send the current
generated diagnosis protocol online. (Note: Do not use Guided
Function. The diagnosis log will not be uploaded to GFF paperless)

Exterior
 Test windshield washers (front and rear) for aim and function
 Test exterior lighting functions
 Check key functionality, including seat memory (if equipped);
verify vehicle starts and runs with the start/stop button; verify
all doors lock/unlock with remote and advanced key, including
all door handle sensors with the advanced key (if equipped)
 Adjust the trunk lid opening height to 75 inches (190 cm) from
the ground to the close button in the rear lid. Press and hold
the close button in the rear lid for at least four seconds to
program the opening height
Interior

Transport Mode Deactivation, DTC check, set service reminder
*It is advised to start ODIS with the engine running to enable all
5F Test Plans in GFF and also to ensure SVM sees all control units
during the SVM check vehicle configuration
 Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating )
 Set service reminder (via Special functions –> Service work –>
17-PDI-resetting SRI at PDI, counter reset, etc.)
 For MMI3G+ vehicles, set adaptation channel (via Special
functions –> Service work –> : 5F–Activating/deactivating
storage of music). Also referred to as CD Ripping. Perform hard
reset of the MMI to complete the activation

 Check operation of all switches: Locks, windows, seat adjustment, seat heating (if equipped) and child safety features
 Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
 Verify operation of all interior lights
 Mirrors: Inspect folding, adjustments, RH tilt in reverse, and
memory (if equipped)
 Inspect operation of outlet in front of center console and
behind center console
 Verify operation of all front and rear seat belts and latches
 Check horn operation

 Perform an SVM specified /actual comparison (via Special
functions ->Software Version Management (SVM))

 Check sunroof and sunshade operation (open/close/vent/
deflector at edge)

 Perform any campaign update requiring SVM at this time
(follow instructions listed in campaign documentation)

 Passenger side airbag: Verify operation of Passenger Occupant
Detection System

Under the Hood Fluid Check and Inspection

Radio

 Check all fluid levels and top off if necessary

 Verify operation of DVD player
 Verify operation of AMI

Effective 7-7-2014-US
Version 1.1

1 of 3

PERFECT DELIVERY INSPECTION (PDI)

2015 Q3 | Audi Technician Report

Radio (continued)

Audi connect (if equipped) (USA ONLY) (continued)

 SD card slot: Insert SD card and test function (Test all SD card
slots as equipped)

 Check Wi-Fi hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX,” where XXXXX = the last five digits
of VIN that are automatically preset in the system.

 Verify HD Radio is turned “off” in Radio/Settings Menu

Audi MMI/Navigation
 Verify and set Language and Measurement Units in Setup Menu
 Set Time source setting to “GPS” and set Auto daylight savings
time to “on.” Change time zone appropriate to the dealer
location
 Navigation (if equipped): Set dealership location (for following
back to dealership during road test)
 Set the “Music volume while parking” to 6 lines (accessed via
MMI rear view camera display: Settings > Music volume while
parking) (applies to vehicles with park assist or rear view
camera)
 Voice Activation (if equipped): Press the “Talk” button and
verify several Commands

On-Hoist Inspection
 Check underside of vehicle for fluid leaks and loose components
 Check steering, boots, brake system, hoses, tires and wheels
for damage
 Remove transport suspension blocks (if installed)
 Inspect wheel bolts for proper torque using torque wrench
 Install wheel bolt covers and center caps as supplied
 If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2015 Normal Load Condition Tire Pressure
Table” posted on ServiceNet. If going to stock, set to maximum
recommended tire pressures listed on the B-pillar doorjamb,
and store tire pressure values in Car/System menu
Road Test

Onboard Video Tutorials

 Check for squeaks, rattles and wind noise

 Load Onboard Video Tutorials

 Verify operation of Audi parking system plus with rear view
camera (if equipped)

 Turn ignition on
 Insert the Onboard DVD into the DVD Drive
 Select the CAR function button. System will initialize
 Select the Owner’s Man. function by selecting the upper right
control button

 Verify engine performance and acceleration
 Verify transmission operation, including shift paddles (if
equipped)
 Check steering/tire alignment

 Select “CD/DVD”

 Test drive vehicle applying brakes several times (at least 4
times) at 20 mph (32 km/h) to clean brake rotors. Check for
abnormal noise/vibration/pulsation

 Select “Start update”

 Parking brake: Apply and verify hold and release

 Turn off ignition to start update (the update will take approx. 5
minutes)

 Verify quality of radio reception in Sirius bands

 Once completed, remove the disk and place back into the case
for the next vehicle

 Verify Audi side assist functionality (if equipped)

 Select “Yes”

Audi connect (if equipped) (USA ONLY)
 Verify Audi connect Information Packet is present, including
Audi brochure, T-Mobile brochure, customer SIM card, T-Mobile
Terms & Conditions (T&C) (if applicable)
 Connect the dealer demo SIM card to the vehicle and make
sure the system fully connects to 2G or 3G (2G or 3G symbol
with Box surrounding it)(only applies if in a T-Mobile service
area)
 Enable Google Earth in the navigation settings and verify the
white Google Logo appears next to the 2G or 3G symbol
 Ensure the wireless network is turned on (TEL function button
> Settings Ctrl button > Wi-Fi settings > Wi-Fi active > select
“Visible”)
Effective 7-7-2014-US
Version 1.1

 Verify cruise control function
 Climate control: Check all functions and ensure proper A/C
cooling
 Seat heating (if equipped): Inspect for proper operation
 Navigation function (if equipped): Activate NAV and follow
directions back to dealership
Post-Road Test Inspection
 Interrogate fault memory using the Scan Tool and print
Diagnostic Log
 Record final mileage on checklist and sign checklist
 Ensure the yellow tire pressure tag is installed on steering
wheel

2 of 3

PERFECT DELIVERY INSPECTION (PDI)

2015 Q3 | Audi Technician Report

Showroom Display/Inventory Storage/Demo Vehicle
 Install showroom charger to ensure battery remains charged at
all times
 Apply Inventory Maintenance Sticker
 Install standard wiper blades (if not already installed)
Technician
I certify that all operations have been completed and this vehicle has been prepared in accordance with Audi Procedures and
Quality Standards, and has met the standards for Perfect Delivery.
Last 8 of VIN

Effective 7-7-2014-US
Version 1.1

Technician Signature

Completion Date

3 of 3