PERFECT DELIVERY INSPECTION (PDI)

2015

A8/A8 L/A8 W12/S8/A8 L TDI

Audi Technician
Report

Stock No.

Dealer Number

R.O. No.

VIN

Road test mileage out

Road test mileage in

All items must be completed prior to customer delivery by an Audi
technician
**Refer to the Special functions tab of ODIS Diagnosis using GFF
for the PDI function tests
**Audi recommends using an Audi approved battery charger to
prevent excessive battery discharge during inspection

Trunk Inspection
 Install wheel bolt cover removal tool from PDI kit into trunk lid
toolkit
 Place the lug cap removal tool, located in the bypack, into the
toolkit (where applicable)
 Set spare tire pressure

Open Campaigns/Updates

 Verify operation of Hands-free trunk release (if equipped)

 Check Elsa for open campaigns and updates. Perform
campaigns not requiring SVM if applicable. Campaigns
requiring SVM should only be performed after the vehicle has
been taken out of transport mode

 Verify operation of trunk emergency release handle
Exterior
 Test windshield washers for aim and function

Battery Inspection

 Turn on headlights and test headlamp washers

 Check battery clamps for proper torque. Re-torque if required

 Test exterior lighting functions

 Perform the A-battery test for new batteries using GFF in ODIS
Diagnosis –> Special functions –> Service work. Select option 2,
the battery test for new batteries as part of the pre–delivery
inspection and act according to the test result (ok, recharge,
replace). Ensure diagnosis log is uploaded to the GFF paperless
server by selecting “ok” when tester wants to send the current
generated diagnosis protocol online. (Note: Do not use Guided
Function. The diagnosis log will not be uploaded to GFF paperless)

 Check key functionality including seat and steering wheel
position memory; verify vehicle starts and runs with all keys
and the start/stop button; verify all doors manually and
remotely lock/unlock with all keys, including all door handle
sensors with the Advanced Key (if equipped)

Transport Mode Deactivation, DTC check, set service reminder
*It is advised to start ODIS with the engine running to enable all
5F Test Plans in GFF and also to ensure SVM sees all control units
during the SVM check vehicle configuration
 Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating )
 Deactivate air suspension loading mode (via Special Functions
-> Service Work -> 34-Loading mode activating/deactivating)
Warning! Car body may lower!

 Power door closing feature: Check all doors for proper closing
(if equipped)
Interior
 Check operation of all switches: Locks, windows, seat adjustment, seat ventilation and massage (if equipped), heated seats
and child safety features
 Rear view mirror: Check self-dimming function/lighting
 Verify operation of all interior lights, including ambient lighting
 Verify operation of all front and rear seatbelts and latches
 Mirrors: Inspect folding, adjustments, RH tilt in reverse, and
memory

 Set service reminder (via Special functions –> Service work –>
17-PDI-resetting SRI at PDI, counter reset, etc.)

 Inspect operation of lighter, aux. outlet under armrest and rear
outlet

 For MMI3G+ vehicles, set adaptation channel (via Special
functions –> Service work –> : 5F–Activating/deactivating
storage of music). Also referred to as CD Ripping. Perform hard
reset of the MMI to complete the activation

 Check horn operation

 Perform any campaign update requiring SVM at this time
(follow instructions listed in campaign documentation)
Under the Hood Fluid Check and Inspection
 Check all fluid levels and top off if necessary
Effective 7-7-2014-US
Version 1.1

 Check sunroof operation (open/close/vent/deflector at edge) (if
equipped)
 Check power rear and rear side sunshade operation (if
equipped)
 Verify operation of rear side manual sunshades (if equipped)
 Verify operation of Head-up Display (if equipped)
 Turn on the night vision camera and verify operation (if
equipped)
1 of 3

PERFECT DELIVERY INSPECTION (PDI)

2015 A8/A8 L/A8 W12/S8/A8 L TDI| Audi Technician Report

Interior (continued)

Onboard Video Tutorials (continued)

 Rear Climate Controls: Verify heating and cooling functions (if
equipped)

 Turn off ignition to start update (the update will take approx. 5
minutes)

 Passenger side airbag: Verify operation of Passenger Occupant
Detection System

 Once completed, remove the disk and place back into the case
for the next vehicle

 Start-Stop-System info (if applicable): Verify the velum sticker
is on the start/stop button. Remove the Start-Stop-System
information card from the car kit and place it in the glove box
with the owner’s manuals. Additional supply can be ordered via
the Brand Store on AccessAudi
Radio
 Verify operation of DVD changer (if equipped)
 Verify operation of DVD player
 Verify operation of AMI
 SD card slot: Insert SD card and test function (Test all SD card
slots as equipped)
 Verify HD Radio is turned “off” in Radio/Settings Menu
Audi MMI/Navigation
 Verify and set Language and Measurement Units in Setup Menu
 Set Time source setting to “GPS” and set Auto daylight savings
time to “on.” Change time zone to the appropriate dealer
location
 Program the radio presets to local stations
 Navigation: Set dealership location (for following back to
dealership during road test)
 Set the “Music volume while parking” to 6 lines (accessed via
MMI rear view camera display: Settings > Music volume while
parking)(applies to vehicles with park assist or rear view camera)
 Voice Activation: Press the “Talk” button and verify several
commands
 Rear Seat Entertainment/Rear MMI (if applicable): Verify
operation. Verify the wireless headphones are present and pair
them to the RSE system (refer to RSE manual). When pairing the headphones, press and hold the on/off button for 4–5
seconds until the light starts flashing quickly

Audi connect (USA ONLY)
 Verify Audi connect Information Packet is present, including:
Audi brochure, T-Mobile brochure, customer SIM card, T-Mobile
Terms & Conditions (T&C)
 Connect the dealer demo SIM card to the vehicle and make
sure the system fully connects to 2G or 3G (2G or 3G symbol
with Box surrounding it) (only applies if in a T-Mobile service
area)
 Enable Google Earth in the navigation settings and verify the
white Google Logo appears next to the 2G or 3G symbol
 Ensure the wireless network is turned on (TEL function button >
Settings Ctrl button > Wi-Fi settings > Wi-Fi active > select
“Visible”)
 Check Wi-Fi hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX,” where XXXXX = the last five digits
of VIN that are automatically preset in the system
On-Hoist Inspection
 Inspect wheel bolts for proper torque using torque wrench
 Check underside of vehicle for fluid leaks and loose
components
 Check steering, boots, brake system, hoses, tires and wheels
for damage
 Install wheel bolt covers from PDI kit on all wheels
 If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2015 Normal Load Condition Tire Pressure
Table” posted on ServiceNet. If going to stock, set to maximum
recommended tire pressures listed on the B-pillar doorjamb,
and store tire pressure values in Car/System menu
Road Test Inspection
 Check for squeaks, rattles and wind noise

Onboard Video Tutorials

 Verify operation of Audi parking system plus with rear view
camera and top or corner view cameras (if equipped)

 Load Onboard Video Tutorials

 Verify engine performance and acceleration

 Turn ignition on

 Verify transmission operation, including shift paddles

 Insert the Onboard DVD into the DVD Drive

 Check Adaptive air suspension in all positions

 Select the CAR function button. System will initialize

 Verify engine Start-Stop-System functionality (if equipped)

 Select the Owner’s Man. function by selecting the upper right
control button

 Check steering/tire alignment

 Select “Yes”
 Select “CD/DVD”
 Select “Start update”
Effective 7-7-2014-US
Version 1.1

 Check heated steering wheel operation (if equipped)
 Test drive vehicle applying brakes at least 4 times at 20 mph
(35 km/h) to clean brake rotors. Check for abnormal noise/
vibration

2 of 3

PERFECT DELIVERY INSPECTION (PDI)

2015 A8/A8 L/A8 W12/S8/A8 L TDI| Audi Technician Report

Road Test Inspection (continued)
 Verify quality of radio reception in AM/FM/SAT bands
 Verify cruise control/ACC with Stop & Go functionality (if
equipped)
 Verify Audi side assist functionality (if equipped)
 Verify Audi lane assist functionality (if equipped)

If Vehicle is for Showroom Display/Inventory Storage or Demo
Use
 Install showroom charger to ensure battery remains charged at
all times
 Apply Inventory Maintenance Sticker
 Install standard wiper blades (if not already installed)

 Climate Control: Check heating and cooling functions
 Seat heating: Inspect for proper operation
 Navigation function: Activate NAV and follow directions back to
dealership
Post-Road Test Inspection
 Interrogate fault memory using the VAS tester and print
Diagnostic Log
 Record final mileage on checklist and sign checklist
 Ensure the yellow tire pressure tag is installed on steering
wheel
Technician
I certify that all operations have been completed and this vehicle has been prepared in accordance with Audi Procedures and
Quality Standards, and has met the standards for Perfect Delivery.
Last 8 of VIN

Effective 7-7-2014-US
Version 1.1

Technician Signature

Completion Date

3 of 3