PERFECT DELIVERY INSPECTION (PDI)

2015

A6/S6/A6 TDI

Audi Technician Report

Stock No.

Dealer Number

R.O. No.

VIN

Road test mileage out

Road test mileage in

All items must be completed prior to customer delivery by an Audi
technician
**Refer to the Special functions tab of ODIS Diagnosis using GFF
for the PDI function tests
**Audi recommends using an Audi approved battery charger to
prevent excessive battery discharge during inspection

Under the Hood Fluid Check and Inspection
 Check all fluid levels and top off if necessary
 Check engine oil level via the MMI – fill oil to the max level
when the vehicle is at operating temperature
Trunk Inspection

Open Campaigns/Updates
 Check Elsa for open campaigns and updates. Perform
campaigns not requiring SVM if applicable. Campaigns
requiring SVM should only be performed after the vehicle has
been taken out of transport mode
Battery Inspection
 Check battery clamps for proper torque. Re-torque if required
 Perform the A-battery test for new batteries using GFF in ODIS
Diagnosis –> Special functions –> Service work. Select option 2,
the battery test for new batteries as part of the pre–delivery
inspection and act according to the test result (ok, recharge,
replace). Ensure diagnosis log is uploaded to the GFF paperless
server by selecting “ok” when tester wants to send the current
generated diagnosis protocol online. (Note: Do not use Guided
Function. The diagnosis log will not be uploaded to GFF paperless)
Transport Mode Deactivation, DTC check, set service reminder
*It is advised to start ODIS with the engine running to enable all
5F Test Plans in GFF and also to ensure SVM sees all control units
during the SVM check vehicle configuration
 Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating )
 Deactivate air suspension loading mode (via Special Functions
-> Service Work -> 34-Loading mode activating/deactivating)
(S6 only)
Warning! Car body may lower!
 Set service reminder (via Special functions –> Service work –>
17-PDI-resetting SRI at PDI, counter reset, etc.)
 For MMI3G+ vehicles, set adaptation channel (via Special
functions –> Service work –> : 5F–Activating/deactivating
storage of music). Also referred to as CD Ripping. Perform hard
reset of the MMI to complete the activation
 Perform any campaign update requiring SVM at this time
(follow instructions listed in campaign documentation)

Effective 7-7-2014-US
Version 1.1

 Install wheel bolt cover removal tool from PDI kit into trunk lid
toolkit
 Place the lug cap removal tool, located in the bypack, into the
toolkit (where applicable)
 Set spare tire pressure
 Verify operation of trunk emergency release handle
Exterior
 Test windshield washers for aim and function
 Turn on headlights and test headlamp washers
 Test exterior lighting functions
 Check tailgate opening and closing with remote (if applicable)
 Check key functionality: Including seat and steering wheel position memory (if applicable); verify vehicle starts and runs with
the start/stop button; verify all doors lock/unlock with remote
and advanced key, including all door handle sensors with the
advanced key (if equipped)
 Start-Stop-System info (if applicable): Verify the velum sticker
is on the start/stop button. Remove the Start-Stop-System
information card from the car kit and place it in the glove box
with the owner’s manuals. Additional supply can be ordered via
the Brand Store on AccessAudi
Interior
 Check operation of all switches: locks, windows, seat adjustment, seat ventilation/heating (front and rear where applicable) and child safety features
 Rear view mirror: Check self-dimming function/lighting (if
equipped)
 Verify operation of all interior lights, including ambient lighting
 Mirrors: Inspect folding, adjustments, RH tilt in reverse, and
memory
 Inspect operation of lighter, aux. outlet under armrest, under
rear vent outlets, and in luggage compartment on passenger side

1 of 3

PERFECT DELIVERY INSPECTION (PDI)

2015 A6/S6/A6 TDI | Audi Technician Report

Interior (continued)

Onboard Video Tutorials (continued)

 Verify operation of all front and rear seat belts and latches

 Turn off ignition to start update (The update will take approx.
5 minutes)

 Check horn operation
 Check sunroof operation (open/close/vent/deflector at edge)
 Verify operation of rear side manual sunshades (if equipped)
 Verify operation of power rear sunshade (if equipped)
 Turn on the night vision camera and verify operation (if
equipped)
 Rear Climate Controls: Verify heating and cooling functions and
open all rear panel vents (center & b-pillar)

 Once completed, remove the disk and place back into the case
for the next vehicle
Audi connect (if equipped) (USA ONLY)
 Verify Audi connect Information Packet is present, including
Audi brochure, T-Mobile brochure, customer SIM card, T-Mobile
Terms & Conditions (T&C)(if applicable)

 Passenger side airbag: Verify operation of Passenger Occupant
Detection System

 Connect the dealer demo SIM card to the vehicle and make
sure the system fully connects to 2G or 3G (2G or 3G symbol
with Box surrounding it)(only applies if in a T-Mobile service
area)

Radio

 Enable Google Earth in the navigation settings and verify the
white Google Logo appears next to the 2G or 3G symbol

 Verify operation of CD changer (if equipped)
 Verify operation of DVD player
 Verify operation of AMI
 SD card slot: Insert SD card and test function (Test all SD card
slots as equipped)
 Verify HD Radio is turned “off” in Radio/Settings Menu
Audi MMI/Navigation
 Verify and set Language and Measurement Units in Setup Menu
 Set Time source setting to “GPS” and set Auto daylight savings
time to “on.” Change time zone appropriate to the dealer
location
 Program the presets to local stations
 Navigation: Set dealership location (for following back to
dealership during road test)

 Ensure the wireless network is turned on (TEL function button
> Settings Ctrl button > Wi-Fi settings > Wi-Fi active > select
“Visible”)
 Check Wi-Fi hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX,” where XXXXX = the last five digits
of VIN that are automatically preset in the system.
On-Hoist Inspection
 Inspect wheel bolts for proper torque using torque wrench
 Check underside of vehicle for fluid leaks and loose
components
 Check steering, boots, brake system, hoses, tires and wheels
for damage
 Install wheel bolt covers from PDI kit on all wheels
 Remove Transport Blocks from shocks

 Voice Activation: Press the “Talk” button and verify several
commands

 After removing transport blocks, secure Additional Springs
(a.k.a. bump stops) by pressing into tube of upper shock mount

 Set the “Music volume while parking” to 6 lines (accessed via MMI
rear view camera display, Settings > Music volume while parking)
(applies to vehicles with park assist or rear view camera).

 If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2015 Normal Load Condition Tire Pressure
Table” posted on ServiceNet. If going to stock, set to maximum
recommended tire pressures listed on the B-pillar doorjamb,
and store tire pressure values in Car/System menu

Onboard Video Tutorials
 Load Onboard Video Tutorials
 Turn ignition on
 Insert the Onboard DVD into the DVD Drive
 Select the CAR function button. System will initialize
 Select the Owner’s Man. function by selecting the upper right
control button

Road Test
 Check for squeaks, rattles and wind noise
 Verify operation of Audi parking system plus with rear view
camera and top or corner view cameras (if equipped)

 Select “Yes”

 Verify Vehicle Head-up Display functionality. Verify the image
can be adjusted properly in the viewing area of the windshield
(if equipped)

 Select “CD/DVD”

 Verify engine performance and acceleration

 Select “Start update”

 Verify transmission operation, including shift paddles
 Verify engine Start-Stop System functionality (if equipped)

Effective 7-7-2014-US
Version 1.1

2 of 3

PERFECT DELIVERY INSPECTION (PDI)

2015 A6/S6/A6 TDI | Audi Technician Report

Road Test (continued)

Post-Road Test Inspection

 Check steering/tire alignment

 Interrogate fault memory using the VAS tester and print
Diagnostic Log

 Check heated steering wheel operation (if equipped)
 Test drive vehicle applying brakes at least 4 times at 20 mph
(35 km/h) to clean brake rotors. Check for abnormal noise/
vibration (refer to TSB 2035669)

 Record final mileage on checklist and sign checklist
 Ensure the yellow tire pressure tag is installed on steering
wheel

 Verify quality of radio reception in AM/FM/SAT bands
 Verify cruise control/ACC with Stop & Go functionality (if
equipped)

If Vehicle is for Showroom Display/Inventory Storage or Demo
Use

 Verify Audi side assist functionality (if equipped)

 Install showroom charger to ensure battery remains charged at
all times

 Verify Audi active lane assist (if equipped)
 Climate Control: Check heating and cooling functions and open
all panel vents

 Apply Inventory Maintenance Sticker
 Install standard wiper blades (if not already installed)

 Seat heating and cooling (if equipped): Check for proper operation
 Navigation function: Activate NAV and follow directions back to
dealership
 Verify NAV directions are visible in Head-Up Display (if
equipped)

Technician
I certify that all operations have been completed and this vehicle has been prepared in accordance with Audi Procedures and
Quality Standards, and has met the standards for Perfect Delivery.
Last 8 of VIN

Effective 7-7-2014-US
Version 1.1

Technician Signature

Completion Date

3 of 3