PERFECT DELIVERY INSPECTION (PDI)

2015

A4/S4/allroad

Audi Technician Report

Stock No.

Dealer Number

R.O. No.

VIN

Road test mileage out

Road test mileage in

All items must be completed prior to customer delivery by an Audi
technician
**Refer to the Special functions tab of ODIS Diagnosis using GFF
for the PDI function tests
**Audi recommends using an Audi approved battery charger to
prevent excessive battery discharge during inspection

Trunk Inspection
 Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit behind right side
cover
 Set spare tire pressure
 Verify operation of trunk emergency release handle (if equipped)

Open Campaigns/Updates
 Check Elsa for open campaigns and updates. Perform
campaigns not requiring SVM if applicable. Campaigns
requiring SVM should only be performed after the vehicle has
been taken out of transport mode
Battery Inspection
 Check battery clamps for proper torque. Re-torque if required
 Perform the A-battery test for new batteries using GFF in ODIS
Diagnosis –> Special functions –> Service work. Select option
2, the battery test for new batteries as part of the pre–delivery
inspection and act according to the test result (ok, recharge,
replace). Ensure diagnosis log is uploaded to the GFF paperless
server by selecting “ok” when tester wants to send the current
generated diagnosis protocol online. (Note: Do not use Guided
Function. The diagnosis log will not be uploaded to GFF paperless)
Transport Mode Deactivation, DTC check, set service reminder

Exterior
 Test windshield washers and headlight washers (if equipped)
for aim and function
 Test exterior lighting functions
 Check key functionality including seat memory (if applicable),
verify vehicle starts and runs with the start/stop button, verify
all doors lock/unlock with remote and Advanced Key, including
door handle sensors (if equipped)
 Verify power rear lid/tailgate (allroad) is operational
Interior
 Check operation of all switches: locks, windows, seat adjustment, power rear sunshade (if equipped) and child safety
features
 Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)

*It is advised to start ODIS with the engine running to enable all
5F Test Plans in GFF and also to ensure SVM sees all control units
during the SVM check vehicle configuration

 Verify operation of all interior lights

 Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating )

 Inspect operation of lighter, aux. outlet under armrest and rear
outlet

 Set service reminder (via Special functions –> Service work –>
17-PDI-resetting SRI at PDI, counter reset, etc.)

 Verify operation of all front and rear seat belts and latches

 For MMI3G+ vehicles, set adaptation channel (via Special
functions –> Service work –> : 5F–Activating/deactivating
storage of music). Also referred to as CD Ripping. Perform hard
reset of the MMI to complete the activation
 Perform any campaign update requiring SVM at this time
(follow instructions listed in campaign documentation)

 Mirrors: Inspect folding, adjustments, RH tilt in reverse, and
memory (if equipped)

 Check horn operation
 Check sunroof operation (open/close/vent/deflector at edge)
 Passenger side airbag: Verify operation of Passenger Occupant
Detection System
Radio
 Verify operation of CD player

Under the Hood Fluid Check and Inspection
 Check all fluid levels and top off if necessary
 Check engine oil level using Special Tool T40178 on a flat and
level surface
Effective 7-7-2014-US
Version 1.1

 Verify operation of AMI or aux. input (if equipped)
 SD card slot: Insert SD card and test function (Test all SD card
slots as equipped)
 Verify HD Radio is turned “off” in Radio/Settings Menu
1 of 3

PERFECT DELIVERY INSPECTION (PDI)

2015 A4/S4/allroad | Audi Technician Report

Audi MMI/Navigation

On-Hoist Inspection (continued)

 Verify and set Language and Measurement Units in Setup/
Settings menu

 Remove transport suspension blocks (if installed)

 Set Time source setting to “GPS” and set Auto daylight savings
time to “on.” Change time zone appropriate to the dealer
location
 Navigation location: Set dealership location (for following back
to dealership during road test)
 Set the “Music volume while parking” to 6 lines (accessed via
MMI rear view camera display:
Settings > Music volume while parking)(applies to vehicles with
park assist or rear view camera)
 Voice Activation (if equipped): Press the “Talk” button and
verify several commands
Onboard Video Tutorials
 Load Onboard Video Tutorials
 Turn ignition on
 Insert the Onboard DVD into the DVD Drive

 Inspect wheel bolts for proper torque using torque wrench
 Install wheel bolt covers and center caps as supplied
 If a known “sold” unit, set to appropriate Normal Load
Condition. See separate “2015 Normal Load Condition Tire
Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
doorjamb, and store tire pressure values in Car/System menu
Road Test
 Check for squeaks, rattles and wind noise
 Verify engine performance and acceleration
 Verify operation of rear view camera and rear parking sensors
(if equipped)
 Verify Audi side assist functionality (if equipped)
 Verify Audi active lane assist functionality (if equipped)

 Select the CAR function button. System will initialize

 Verify transmission operation, including shift paddles (if
equipped)

 Select the Owner’s Man. function by selecting the upper right
control button

 Check steering/tire alignment

 Select “CD/DVD”

 Test drive vehicle, applying brakes at least 4 times at 20 mph
(35 km/h) to clean brake rotors Check for abnormal noise/
vibration/pulsation

 Select “Start update”

 Parking brake: Apply and verify hold and release

 Turn off ignition to start update (the update will take approx. 5
minutes)

 Verify quality of radio reception in AM/FM/SAT bands

 Once completed, remove the disk and place back into the case
for the next vehicle

 Seat heating (if equipped): Inspect for proper operation

 Select “Yes”

Audi connect (USA ONLY) (if equipped)
 Verify Audi connect Information Packet is present, including
Audi brochure, T-Mobile brochure, customer SIM card, T-Mobile
Terms & Conditions (T&C)(if applicable)

 Verify cruise control/ACC (if equipped)
 Climate control: Check all functions and ensure proper A/C
cooling
 Navigation function (if equipped): Activate NAV and follow
directions back to dealership

 Connect the dealer demo SIM card to the vehicle and make
sure the system fully connects to 2G or 3G (2G or 3G symbol
with arrows)(only applies if in a T-Mobile service area)

Post-Road Test Inspection

 Enable Google Earth in the navigation settings and verify the
white Google Logo appears next to the 2G or 3G symbol

 Record final mileage on checklist and sign checklist

 Ensure the wireless network is turned on (TEL function button
> Settings Ctrl button > Wi-Fi settings > Wi-Fi active > select
“Visible”)
 Check Wi-Fi hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX,” where XXXXX = the last five digits
of VIN that are automatically preset in the system.
On-Hoist Inspection
 Check underside of vehicle for fluid leaks and loose components

 Interrogate fault memory using the Scan Tool and print
Diagnostic Log
 Ensure the yellow tire pressure tag is installed on steering
wheel
Showroom Display / Inventory Storage / Demo Vehicle
 Install showroom charger to ensure battery remains charged at
all times
 Apply Inventory Maintenance Sticker
 Install standard wiper blades (if not already installed)

 Check steering, boots, brake system, hoses, tires and wheels
for damage
Effective 7-7-2014-US
Version 1.1

2 of 3

PERFECT DELIVERY INSPECTION (PDI)

2015 A4/S4/allroad | Audi Technician Report

Technician
I certify that all operations have been completed and this vehicle has been prepared in accordance with Audi Procedures and
Quality Standards, and has met the standards for Perfect Delivery.
Last 8 of VIN

Effective 7-7-2014-US
Version 1.1

Technician Signature

Completion Date

3 of 3