Technical Service Bulletin
01 MIL on (P0300 and/or P0301, P0302, P0303, P0304 - cylinder misfire detected)
01 14 63 2033630/2 January 31, 2014. Supersedes Technical Service Bulletin Group 01 number 13-86 dated April
15, 2013 for reasons listed below.
Model(s)

Year

A3, A4, allroad,
TT, A5, A5
Cabriolet, Q5

2008- 2015

A6

2012 -2015

VIN Range

Vehicle-Specific Equipment

All

4 Cylinder Engines

Condition
REVISION HISTORY
Revision

Date

Purpose

2

-

Revised header data (Updated applicable engine codes; added DTCs)
Revised title

1

04/15/2013

Initial publication

• MIL on.
• Rough idle.
• One or more of the following DTCs are stored in the Engine Control Module (ECM), J623 (address word 01):
• DTC P0300 (Random/Multiple Cylinder Misfire Detected).
• DTC P0301 (Cylinder 1 Misfire Detected)
• DTC P0302 (Cylinder 2 Misfire Detected)
• DTC P0303 (Cylinder 3 Misfire Detected)
• DTC P0304 (Cylinder 4 Misfire Detected)
• Engine may have reduced performance without significant loss of power or stalling.

Technical Background
Because there are a number of different misfire faults (unrelated to ignition coil operation) that could cause the
MIL to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils
are replaced.

Production Solution
Improved ignition coil since 2008 model year.
© 2014 Audi of America, Inc.

Page 1 of 3

All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior
expressed written permission of the publisher.

Technical Service Bulletin
Service
Obtain information from the customer
Ask the customer the following questions about the symptoms of the condition and when it occurred. This
information will be necessary for duplicating the condition during service.
• In what situation (while turning, etc.) does the condition occur?
• Under what environmental conditions (road conditions, weather, temperature, start conditions, etc.) does the
condition occur?
• What is the operating situation of the vehicle (activated electrical equipment, gear selected, etc.) when the
condition occurs?
• Can the complaint be reproduced?
Workshop procedure
1. Read out the data memory of all engine control units and note the environmental conditions on the DTC log.
• If there are other entries in addition to combustion misfires, address the other entries before addressing
the cylinder misfires.
• If DTC P0301 – P0304 (Cylinder 1 Misfire Detected – Cylinder 4 Misfire Detected) is accompanied by DTC
P1250 (Fuel Level Too Low), it is likely the faults occurred due to a low fuel level and not due to a
malfunction of the coils.
• Review all applicable technical service bulletins (TSBs) related to cylinder misfires and ECM software
improvements before diagnosing the misfire condition. For example, if the data shows that the DTC was
set during cold start, search ElsaWeb for TSBs related to cold start misfires.
2. Try to duplicate the customer complaint based on the environmental conditions at the time the DTC was set.
The freeze frame data gives important indicators for the traceability of the complaint, particularly if it occurs
sporadically or at cold start.
3. Review the vehicle repair history for previous misfire service or other maintenance service that could be
related to the current complaint.
4. Observe the requirements of GFF. Perform GFF in full according to the proposed sequence (test plan). Do
not skip any steps.
5. Complete GFF correctly and set the readiness code. Doing so will ensure that no subsequent faults occur due
to the misfire.
6. In the case of single cylinder misfires:
• Before replacing components, exchange the coils to determine whether the condition migrates to the other
cylinders after the coils have been exchanged. If necessary, perform a test drive to test the condition.
Note: Always use special tool T40039 to remove ignition coils.
• If the misfire migrates to another cylinder with an exchanged coil, replace only the affected coil.

© 2014 Audi of America, Inc.

Page 2 of 3

All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior
expressed written permission of the publisher.

Technical Service Bulletin
7. Verify the repair under the same environmental conditions (engine speed, engine load value, vehicle speed,
coolant temperature, intake air temperature, ambient air pressure, voltage at terminal 30, etc.) as noted on
the DTC log.

Warranty
This TSB is informational only and not applicable to any Audi warranty.

Required Parts and Tools
Part Number

Part Description

Quantity

T40039

Ignition coil removal tool

1

Additional Information
All parts and service references provided in this TSB (2033630) are subject to change and/or removal. Always
check with your Parts Department and service manuals for the latest information.

© 2014 Audi of America, Inc.

Page 3 of 3

All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior
expressed written permission of the publisher.