Technical Bulletin
Model(s)

Year

Eng. Code

Trans. Code

VIN Range From

VIN Range To

Jetta

2013-2014

2.0L

All

All

All

All

All

All

(CPPA, CPLA)
Beetle, Beetle
Convertible

2013-2014

2.0L
(CPPA, CPLA)

Condition
01 15 01 January 14, 2014 2038575
Update Programming to Eliminate O2 Sensor DTC P2414 and/or P2237 along with O2 Sensor Replacement
Customer states the MIL light is ON, DTCs P2414 and/or P2237 may be present in the ECM fault memory.

DTC

Description

P2414

O2 Sensor Exhaust Sample Error, Bank 1 Sensor 1

P2237

O2 Sensor Positive Current Control Circuit Bank 1
Sensor 1 Open

Technical Background
Current ECM catalyst heating process may cause damage to the front oxygen sensor.

Production Solution
Optimize software.

Page 1 of 6 plus attachment
© 2015 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Technical Bulletin
Service
Update-Programming Procedure:

Tip:
To Update-Programming using SVM, review and follow instructions in Technical Bulletin Instance 2014603
“Software Version Management”.
The SVM Process must be completed in its entirety so the database receives the update confirmation response. A
warranty claim may not be reimbursed if there is no confirmation response to support the claim.

Note:
Prior to launching the ODIS service diagnostic applications and starting control module update process, confirm
tester screen saver and power settings in accordance with Special Tools and Equipment - Service Information
Circular # VVT-12-02. Failure to do so may result in the tester entering power save mode during data transfer, and
subsequent control module failure.
When using a VAS 6150/X or 6160/X tester in conjunction with a VAS 5054A wireless transmitter head for a flash
procedure, please connect a USB cable between the transmitter head and the tester. Failure to do so may lead to
errors during the flash procedure.
VAS tools must only be used with their power adapters plugged in. Under no circumstances should they be used
on battery power alone during the programming procedure.

Critical Warning: : The Midtronics Battery Charger must be connected to the vehicle battery for the duration of
the programming, to ensure the battery state of charge remains above 12.5 volts during the update process. If the
battery drops below 12.5 volts, the programming could fail which may result in damage to the control module.
Control modules damaged by inadequate voltage will not be covered under the warranty policy. The technician
should verify the vehicle voltage prior to starting the update process, and should monitor the voltage for the
duration of the update.
Note:
O2 Sensor must be replaced after the ECM software has been updated.

Page 2 of 6 plus attachment
© 2015 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Technical Bulletin
• Update the Engine Control Module using the SVM Unit code as listed in the table below:

Model

Engine

Old Software
Part No.

Old Software
Version

Jetta

CPLA

06K 906 070 T

4894

New Software New Software SVM Unit
Part #
Version (or
Code
higher)
06K 906 070 T

8093

3AB9

06K 906 070 T

8093

3AB9

06K 906 070
AA

8098

3AB9

5139
5801
6059
6110
6282
6899
7643
8046
Jetta

CPLA

06K 906 070

4052
4228
4241
4356
4475
4877
5134
5527
5780

Beetle, Beetle
Convertible

CPLA

06K 906 070
AA

4879
5136
5782
6061
6115
6271
6900

Page 3 of 6 plus attachment
© 2015 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Technical Bulletin
7648
8051
Beetle, Beetle
Convertible

CPLA

06K 906 070 A

4053
4236

06K 906 070
AA

8098

3AB9

4370
4878
5132
5222
5528
5781

The procedure can be found in GFF under Functions/ Component Selection, Software Version Management,
Adapting Software.

WARNING:
Radiator Fan(s) may cycle ON high speed during the Update Process! There is a risk that personal injury may
result if contact is made with spinning fan blades.
Keep hands and all objects away from Radiator Fan(s) during Update Process!

Tip:
The SVM Process must be completed in its entirety so the database receives the update confirmation response. A
warranty claim may not be reimbursed if there is no confirmation response to support the claim or action is carried
out that is not explicitly stated in the Technical Bulletin.
Ensure attached ECM/TCM Tuning Form has been completed and signed by customer as required in SVM
Technical Bulletin Instance 2014603.
• After Update programming of the ECM has been completed, replace the front oxygen sensor per Elsa
instructions.

Page 4 of 6 plus attachment
© 2015 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Technical Bulletin
Warranty
To determine if this procedure is covered under Warranty, always refer to the Warranty Policies and
1)
Procedures Manual
Model(s)

Year(s)

Eng. Code(s)

Trans. Code(s)

VIN Range From

VIN Range To

Jetta

2013-2014

2.0L

All

All

All

All

All

All

(CPPA, CPLA)
Beetle, Beetle
Convertible

2013-2014

2.0L
(CPPA, CPLA)
SAGA Coding

Claim Type:

Use applicable Claim Type

1)

Damage
Service Number:

HST

Damage Location
(Depends on Service No.)

--

Use applicable when
indicated in ElsaWeb
(L/R)

Code

2470

0039

Parts Manufacturer

Jetta

WWO

Beetle, Beetle Convertible

3ME

2)

2)

3)

27068950 = 10 TU

3)

Included in GFF Time expenditure below

Labor Operation : Charge Battery
Labor Operation : Update Programming
3)

Labor Operation :Remove and Install Engine Cover 10831900 = 20 TU
3)

Labor Operation :Remove and Install Intake Pipe

21131970 = 10 TU

3)

Labor Operation :Remove and Install Front Oxygen 24691970 = 20 TU
Sensor
Causal Part: Oxygen Sensor

06K906262H
Diagnostic Time

4)

Page 5 of 6 plus attachment
© 2015 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Technical Bulletin
GFF Time expenditure

01500000 = 50 TU max.

Road Test

01210002 = 10 TU

YES
YES

01210004 = 10 TU
Technical Diagnosis

01320000 = 00 TU max.

NO

Claim Comment: Input “As per Technical Bulletin 2038575” in comment section of Warranty Claim.
1)

Vehicle may be outside any Warranty in which case this Technical Bulletin is informational only

2)

Code per warranty vendor code policy.

3)

Labor Time Units (TUs) are subject to change with ELSA updates.

4)

Documentation required per Warranty Policies and Procedures Manual.

Required Parts and Tools
Part Description
Front Oxygen Sensor

Part Number
06K906262H

Tool Description

Tool No:

Midtronics Battery Tester/Charger

InCharge 940 (INC-940)
or
GRX3000VAS

VAS Diagnostic Tool

VAS 6150/X & VAS 6160/X with:
ODIS Service with current online updates

Additional Information
All part and service references provided in this Technical Bulletin are subject to change and/or removal.
Always check with your Parts Dept. and Repair Manuals for the latest information.

Page 6 of 6 plus attachment
© 2015 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

OWNER INFORMATION ABOUT CONTROL MODULE TUNING*
ACKNOWLEDGEMENT AND AUTHORIZATION FOR
REPROGRAMMING (REFLASHING) OF CONTROL MODULE(S)
*) “TUNING” is described as the addition of or modification of any component which causes a
Volkswagen vehicle to perform outside the normal parameters and specifications approved by
Volkswagen Group of America / Volkswagen Group Canada.

Date:
Dealer Number:
Vehicle Identification Number:
Repair Order Number:
Dealer stamp

I

, owner or driver of the above identified Volkswagen, confirm:

- “Tuning” as described above (especially power increasing modifications) has NOT been
performed on my vehicle.
- “Tuning” as described above has been performed on my vehicle and the following components
were modified or installed:

TUNING was performed by (Please provide Company name and telephone number, if you wish us
to contact them):

I understand that if my Control Module is determined to have been tuned, any damage caused by
the tuning of the Control Module (including adverse emissions consequences) will not be covered
by VWGoA / VGC warranties.
I am permitting an authorized Volkswagen Dealer to reflash (update) my Control Module, and by
doing so, I understand that this process will automatically overwrite (destroy) and permanently
delete any tuning program that was previously installed on the Control Module of my Volkswagen
vehicle.
By signing below, I fully acknowledge and understand that the tuning program will not be restored
and VWGoA / VGC, will not be liable in any way for the loss of tuning data.

Signature of Customer
E 2015 Volkswagen Group of America Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printi ng and is subject to the copyright and other intellectual
property rights of VGoA / VGCA Inc., its affiliated companies and its licensors. All rights are reserved to ma ke changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitte d in any
form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or rep osted to other sites, without the prior expressed written permission of the publisher .