Classification:

Reference:

Date:

EC16-041

ITB16-051

December 19, 2016

2017 QX80; MIL IS ON WITH DTC P2080 AND/OR P2082
APPLIED VEHICLES:

2017 QX80 (Z62)

IF YOU CONFIRM:
The MIL is ON with DTC


P2080 (EXHAUST GAS TEMP SENSOR 1 B1),

And/or


P2082 (EXHAUST GAS TEMP SENSOR 1 B2).

ACTION:
1. Refer to step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working
on.
2. If this bulletin applies, reprogram the ECM.
NOTE: If this bulletin does apply (the ECM needs to be reprogrammed), do NOT replace the exhaust gas
temp sensor.

IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing.
You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to
successfully completing this repair.
Infiniti Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained
individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe
that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Infiniti retailer to determine if this
applies to your vehicle.

1/10

SERVICE PROCEDURE
NOTE:


Most instructions for reprogramming with CONSULT-III plus (C-III plus) are displayed on the CONSULT
PC screen.



If you are not familiar with the reprogramming procedure, click here. This will link you to the
"CONSULT- III plus (C-III plus) Reprogramming" general procedure.



Take the vehicle for a 10 minute drive in order to meet the following Idle Air Volume Learn (IAVL)
conditions:

 Engine coolant temperature: 70 - 105°C
(158 - 221°F)
 Battery voltage: More than 12.9V (at idle)
 Transmission: Warmed up
Figure A
NOTE: After reprogramming is complete, you will be required to perform Throttle Valve Closed
Position, Idle Air Volume Learn, Accelerator Closed Position, and DTC erase. The above conditions are
required for IAVL to complete.

CAUTION:


Connect the GR8 to the 12V battery and set to ECM power supply mode.
If the vehicle battery voltage drops below 12.0V or above 15.5V during reprogramming, the ECM
may be damaged.



Be sure to turn OFF all vehicle electrical loads.
If a vehicle electrical load remains ON, the ECM may be damaged.



Be sure to connect the AC Adapter.
If the CONSULT PC battery voltage drops during reprogramming, the process will be interrupted
and the ECM may be damaged.



Turn off all external Bluetooth® devices (e.g., cell phones, printers, etc.) within range of the
CONSULT PC and the plus VI. If Bluetooth® signal waves are within range of the CONSULT PC
during reprogramming, reprogramming may be interrupted and the ECM may be damaged.

2/10

ITB16-051

1. Connect the CONSULT PC to the vehicle to begin the reprogramming procedure.
2. Open / start C-III plus.
3. Wait for the plus VI to be recognized.


The Serial No. will display when the plus VI is recognized.

4. Select Re/programming, Configuration.

Step 3: plus
VI is
recognized

Step 4

Figure 1

5. Follow the on-screen instructions and navigate C-III plus to the screen shown in Figure 2 on the next page.

3/10

ITB16-051

6. When you get to the screen shown in Figure 2, confirm this bulletin applies as follows.
A. Find the ECM Part Number and write it on the repair order.
NOTE: This is the current ECM Part Number (P/N).

xxxxxxxxxxxxxxxx

Step 6A:
Current ECM P/N
xxxxx
xxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxx

Figure 2

B. Compare the P/N you wrote down to the numbers in the Current ECM Part Number column in
Table A below.


If there is a match, this bulletin applies. Continue with the reprogramming procedure.



If there is not a match, this bulletin does not apply. Close C-III plus and refer to ASIST for further
diagnostic information.

Table A
Model

Current ECM Part Number: 237105ZP2B, 5ZP3B, 5ZP4B, 5ZP5B

2017 QX80

5ZP2C, 5ZP3C, 5ZP4C, 5ZP5C

4/10

ITB16-051

7. Follow the on-screen instructions to navigate C-III plus and reprogram the ECM.

NOTE:




In some cases, more than one new P/N for reprogramming is available.


If more than one new P/N is available, the screen in Figure 3 displays.



Select and use the reprogramming option that does not have the message “Caution! Use ONLY
with ITBXX-XXX”.

If you get this screen and it is blank (no reprogramming listed), it means there is no reprogramming
available for this vehicle. Close C-III plus and refer back to ASIST for further diagnosis.

xxxxx-xxxxx
xxxxx-xxxxx

xxxxx-xxxxx
xxxxx xxxxx

xxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxx

Figure 3

5/10

ITB16-051

8. When the screen in Figure 4 displays, reprogramming is complete.
NOTE: If the screen in Figure 4 does not display (reprogramming does not complete), refer to ECM
recovery on the next page.
9. Disconnect the GR8 (battery charger) from the vehicle.

10. Select Next.

Step 10

Figure 4
NOTE:


In the next steps, (page 8), you will perform Throttle Valve Closed Position, Idle Air Volume Learn,
Accelerator Closed Position, and DTC erase.



These operations are required before C-III plus will provide the final reprogramming confirmation
report.

6/10

ITB16-051

ECM Recovery
Do not disconnect plus VI or shut down Consult III plus if reprogramming does not complete.
If reprogramming does not complete and the “!?” icon displays as shown in
Figure 5:



Check battery voltage
(12.0 - 15.5 V).



Ignition is ON, engine OFF.



External Bluetooth® devices are
OFF.



All electrical loads are OFF.



Select retry and follow the on
screen instructions.



“Retry” may not go through on first
attempt and can be selected more
than once.
Figure 5

If reprogramming does not complete and the “X” icon displays as shown in
Figure 6:



Check battery voltage
(12.0 - 15.5 V).



CONSULT A/C adapter is plugged
in.



Ignition is ON, engine OFF.



Transmission is in Park.



All C-III plus / VI cables are securely
connected.



All C-III plus updates are installed.



Select Home, and restart the
reprogram procedure from the
beginning.

Figure 6

7/10

ITB16-051

11. Follow the on-screen instructions to perform the following:


Throttle Valve Closed Position



Idle Air Volume Learn (IAVL)
NOTE:

 Listed below are common conditions required for IAVL to complete.
 If IAVL does not complete within a few minutes, a condition may be out of range.
 Refer to the appropriate Electronic Service Manual (ESM) for specific conditions required
for the vehicle you are working on.
o
o
o
o
o
o
o

Engine coolant temperature: 70 -105° C (158 - 221°F)
Battery voltage: More than 12.9V (At idle)
Selector lever: P or N
Electric load switch: OFF (Air conditioner, headlamp, rear window defogger)
Steering wheel: Neutral (Straight-ahead position)
Vehicle speed: Stopped
Transmission: Warmed up



Accelerator Pedal Close Position Learning



Erase DTCs

Continue to the next page.

8/10

ITB16-051

12. When the entire reprogramming process is complete, the screen in Figure 7 will display.
13. Verify the before and after part numbers are different.
14. Print a copy of this screen (Figure 7) and attach it to the repair order for warranty documentation.
15. Select Confirm.

xxxxxx

Step
13

xxxxxx
xxxxxxx
xxxxxxxxxxxxxxxxxxxxxx

xxxxxxxxxxxxxxxxxxxxxx

Step
14

Step
15

Figure 7
16. Close C-III plus.
17. Turn the ignition OFF.
18. Disconnect the plus VI from the vehicle.
19. Test drive the vehicle and make sure it operates correctly and the MIL is OFF.


If the MIL comes ON, go back to ASIST for further diagnostic information.



Diagnosis and repairs beyond ECM reprogramming are not covered by this bulletin.

9/10

ITB16-051

CLAIMS INFORMATION
Submit a Primary Part (PP) type line claim using the following claims coding:
DESCRIPTION
PFP
OP CODE
SYM
DIA
FRT
Reprogram Engine Control Module
(1)
DE97AA
HD
32
(2) (3)
(1) Refer to the electronic parts catalog (FAST) and use the ECM assembly part number (23710-*****) as the
Primary Failed Part (PFP).
(2) Reference the current Infiniti Warranty Flat Rate Manual and use the indicated FRT.
(3) FRT allows adequate time to access DTC codes and reprogram ECM. No other diagnostic procedures
subsequently required. Do NOT claim any Diagnostic Op Codes with this claim.

10/10

ITB16-051