Technical Bulletin
Model(s)

Year

Eng. Code

Trans. Code

VIN Range From

VIN Range To

Tiguan

2011-2015

All

All

All

All

Condition
40 14 05 July 16, 2014 2037509 Supersedes T. B. V401404 dated June 24, 2014 to correct causal part in
warranty table.
Clicking or Popping Noise from the Front Suspension after a Change in Direction
Note:
The symptom as described does not affect the customer’s ability to control the vehicle.
When accelerating after a change of direction (forward or reverse) a one-time clicking or popping noise occurs in
the front left or front right of the vehicle.

Technical Background
The concern is due to the relative movement of the outward drive axle spline in the wheel bearing.

Production Solution
No production change required.

Page 1 of 4
© 2014 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Technical Bulletin
Service
Procedure
• Begin by road testing vehicle to reproduce the customer concern. If unable to duplicate the customer concern,
this bulletin does not apply, continue to diagnose the customer complaint.
If the customer concern can be duplicated, perform the following procedure:
• Remove the drive axle from the affected side following the repair procedure outlined in ELSA Pro.
• Bond the outward splines of the drive axle with liquid locking compound (part number: D 000 600 A2) to the
wheel bearings.

Tip:
Use two continuous beads on the spline. The first
bead should be applied at the beginning of the
spline and the second should be in the center of
the spline teeth (Figure 1, red marks).

Figure 1

• After applying the locking fluid to the spline reinstall the drive axle following the repair procedure outlined in
ELSA.

Note:
Upon completion of the bonding procedure the vehicle must remain stationary for 1 hour.

Page 2 of 4
© 2014 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Technical Bulletin
Warranty
To determine if this procedure is covered under Warranty, always refer to the Warranty Policies and
1)
Procedures Manual
Model(s)

Year(s)

Eng. Code(s)

Trans. Code(s)

VIN Range From

VIN Range To

Tiguan

2011-2015

All

All

All

All

SAGA Coding
Claim Type:

Use applicable Claim Type
Damage

Service Number:

HST

Damage Location
(Depends on Service No.)

--

Use applicable when
indicated in ElsaWeb
(L/R)

Code

4041

0018

Parts Manufacturer

1)

Tiguan

3)

Labor Operation : Remove and Install Drive Axle

WWO

2)

40411900 = 90 TU (One side)
40412000 = 130 TU (Both sides)

Causal Part: Select Labor Operation

4041****
Diagnostic Time

GFF Time expenditure

4)

01500000 = 00 TU max.

NO

01210002 = 10 TU
Road Test

YES
01210004 = 10 TU

Technical Diagnosis

01320000 = 00 TU max.

NO

Claim Comment: Input “As per Technical Bulletin 2037509” in comment section of Warranty Claim.
1)

Vehicle may be outside any Warranty in which case this Technical Bulletin is informational only

2)

Code per warranty vendor code policy.

3)

Labor Time Units (TUs) are subject to change with ELSA updates.

4)

Documentation required per Warranty Policy Procedures Manual.
Page 3 of 4

© 2014 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Technical Bulletin
Required Parts and Tools
Part Description

Part No:

Quantity

Liquid locking compound

D 000 600 A2

.10

No Special Tools required.

Additional Information
All part and service references provided in this Technical Bulletin are subject to change and/or removal.
Always check with your Parts Dept. and Repair Manuals for the latest information.

Page 4 of 4
© 2014 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.