Technical Bulletin
Model(s)

Year

Eng. Code

Trans. Code

VIN Range From

VIN Range To

2011-2015

All

All

All

All

All Models
(except Routan)

Condition
00 14 06 July 2, 2014 2015780 Supersedes T. B. V001206 dated November 2, 2012 to include additional models,
®
model year applicability and example pictures of trapped moisture under RAPGARD .
PDI - Vehicle Inspection, Protection Removal and Detailing

Technical Background
Not applicable.

Production Solution
Not applicable.

Service
INDEX OF INFORMATION
• Inspecting vehicle for damage (to be completed within 48 hours of delivery to Dealership)
• Shipping damage
• Detailers responsibilities (to be completed prior to delivery to Customer)
• Full Body Covers (FBC), removal and disposal
• RAPGARD , removal and disposal
®

• Paint finish, inspecting for swirl marks
• Exterior glass, cleaning
• Interior, cleaning
• New vehicle detailing products

Page 1 of 26
© 2014 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Technical Bulletin
VEHICLE, INSPECTING FOR DAMAGE
Within 48 Hours after arrival at Dealer:
Full Body Cover “FBC”
Some vehicles are shipped with a Full Body Cover.
• Inspect the complete “FBC” cover for damage.
If the “FBC” is damaged (torn, cut etc.):
• Remove cover using appropriate steps to allow for inspection of damage
If any shipping damage is found (see “Shipping Damage”).
®

RAPGARD

®

Vehicles are shipped with RAPGARD . This self-adhering plastic product is applied in certain areas of the
vehicle and is designed to provide protection from all types of possible damages.
SHIPPING DAMAGE
• You must note the damage on the Carrier Delivery Receipt, including damage type, extent and location.
Failure to note damage on the Carrier Delivery Receipt will result in non-payment of the repair.
DETAILERS RESPONSIBILITIES
The Detailer’s role
Taking ownership of a vehicle that is clean, shiny and performs as expected goes a long way in Customer
satisfaction.
The impact you have on the Volkswagen Customer is immense. You play a vital role in delivering a perfect
Volkswagen to your Customers. The delivery process is exciting for our Customers. Your attention to detail will
give a Volkswagen Customer a positive experience about his or her new car far beyond that first day of delivery.
By preparing a perfectly detailed vehicle to your Customer, you are not only meeting or exceeding your
Customer’s expectations, you are also helping eliminate any buyer’s remorse (that feeling of anxiety people get
after making a large or important purchase).
Please know that you have a team behind you with excellent products and support to enable you to make a
perfect delivery each and every time!
Prior to Delivery, following the Perfect Delivery Detailer's Inspection Checklist:
• Rinse vehicle exterior.
• Remove vehicle cover if equipped:
• Remove “FBC” cover
• Remove RAPGARD®

Page 2 of 26
© 2014 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Technical Bulletin
Tip:
While the illustrations shown in this TB reflect the CC model, the removal procedures for other models shipped
with a full cover are the same unless otherwise listed.

Procedure

Tip:
Use the Martor-Cardycut 7469BAG to cut the
Full Body Cover (FBC) at the upper and lower
“A” pillar.

Page 3 of 26
© 2014 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Technical Bulletin
• Remove clips and hooks under the rocker
panel.

• Cut the FBC at the beltline from the “B”
pillar to the taillight.

Page 4 of 26
© 2014 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Technical Bulletin
• Allow FBC to fall away from body panel.

• Cut the FBC from the left taillight to the
right “A” pillar.

Page 5 of 26
© 2014 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Technical Bulletin
Note:
Cut along the beltline until you reach the gas
door cover, make the cut above the gas door
cover then return to the beltline.

• Continue FBC removal at belt line.

Page 6 of 26
© 2014 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Technical Bulletin
• Raise Hood.
• Make a vertical cut through the FBC in the
center of the front of the car.

• Remove all clips and hooks.
The lower half of the FBC should fall away
from the car reducing the possibility of any dirt
or debris damaging the finish.

Page 7 of 26
© 2014 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Technical Bulletin
• Cut the upper FBC around the windshield
and roll cover towards rear of vehicle.
Note:
By rolling FBC off of vehicle you are
minimizing the friction that may cause electric
static discharge.
• Release hooks from hood cover and
remove.

Once “FBC” cover has been removed from vehicle:
• Scrap cover. DO NOT reuse!
• Go to “Detailer responsibilities exterior cont.”
®

RAPGARD REMOVAL AND DISPOSAL

Note:
®

RAPGARD must be removed from the vehicle no later than six months after application. See sticker (location
on vehicle body varies) for detailed information.
®

RAPGARD , Removal
Vehicle must be at room temperature.
The ideal body surface temperature for RAPGARD® removal is 60°F (15.5°C) to 80°F (26.6° C).
If body surface temperatures are below 60°F (15.5°C) or above 80°F (26.6° C) then:
• Removal procedure should be performed indoors after surface temperatures have been allowed to stabilize
within the given range.
• Rinse vehicle thoroughly with water to remove surface dirt or dust and to help stabilize body surface
temperatures.
• Starting at the corners of each panel, carefully remove RAPGARD from vehicle.
®

Page 8 of 26
© 2014 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Technical Bulletin
®

RAPGARD Disposal
RAPGARD® can be disposed as normal paper waste. If unsure about proper disposal procedures in your area,
check local regulations.
®

RAPGARD , Paint Inspection after Removal
Inspect painted surfaces under one of the following lighting conditions:
• Indoors under fluorescent lighting.
• Outdoors under bright sunlight.
Note:
If any defects on the exterior have been identified (scratches, dings, dents and other types of body damage):
Contact your Supervisor and arrange to repair defects immediately. Repairs MUST be completed prior to
delivery.
Tip:
®

After removal of RAPGARD , some vehicles may exhibit temporary paint discoloration or paint swelling (caused
®
by trapped moisture under the RAPGARD ).
• This temporary swelling is caused by the paint finish absorbing moisture trapped under the RAPGARD film.
®

• This swelling will disappear with exposure to the sun or heat lamps within 2 -3 hours. Severe paint swelling
may require 2 -3 days to recover.
DO NOT buff or refinish paint for this condition!
• Trapped moisture example 1

Page 9 of 26
© 2014 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Technical Bulletin
• Trapped moisture example 2

Tip:
Paint discoloration (looks like shaded or dark magic marker lines) can be removed with a heat gun using the
following procedure:
• Hold heat gun approximately 3 in. away from affected paint surfaces and apply heat using slow oscillating
motions until discoloration is gone.
• If discoloration remains, wipe the heated area with Isopropyl alcohol and repeat procedure to increase
surface drying.
If no discoloration is evident or once discoloration is removed, inspect and remove any adhesive residue using
the following products:
®

RAPGARD , Adhesive Residue Removal
Light lines of adhesive residue can be removed with Perfect-It
dark colored vehicles.
3M

TM

Perfect-It

TM

TM

non-abrasive polishing products for light or

Foam Polishing Pad Glaze (for light colored vehicles):

Part Number

Container Size

Containers per Case

MMM039109 DSP

16 oz

6

For bulk quantities see Parts Information Table → Required Parts and Tools

Page 10 of 26
© 2014 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Technical Bulletin
3M

TM

Perfect-It

TM

Foam Polishing Pad Glaze (for dark colored vehicles):

Part Number

Container Size

Containers per Case

MMM039009 DSP

16 oz

6

For bulk quantities see Parts Information Table → Required Parts and Tools

3M

TM

General Purpose Adhesive Cleaner:

Thick lines of adhesive residue can be removed with a general purpose adhesive cleaner.
Part Number

Container Size

Containers per Case

MMM008987 DSP

15 oz.

6

For bulk quantities see Parts Information Table → Required Parts and Tools

Page 11 of 26
© 2014 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Technical Bulletin

With paint finish inspected for discoloration and adhesive residue removed:
• Go to “Detailer Responsibilities Exterior Cont.”
DETAILER RESPONSIBILITIES, EXTERIOR Cont.
3M

TM

Car Wash Shampoo Concentrate

• Wash and dry vehicle exterior.
Part Number

Container Size

Containers per Case

MMM039000 DSP

16 oz.

6

For bulk quantities see Parts Information Table → Required Parts and Tools

Tip:
Page 12 of 26
© 2014 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Technical Bulletin
DO NOT wash or dry vehicle in direct sunlight. Rapid water/soap solution evaporation may form “water spots”
on the paint surface.

Page 13 of 26
© 2014 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Technical Bulletin
Car Wash Mitt
The plush fibers carry an abundance of soap and water to help loosen and lift away dirt and grime from the
vehicle’s surface.

Part Number

Container Size

Containers per Case

ZAW 911 380

N/A

1

Once vehicle has been thoroughly washed:
• Inspect interior floors and glass for water leaks.
• Inspect paint surface, moldings and glass.
Note:
If any defects on the exterior have been identified (scratches, dings, dents and other types of body damage):
Contact your Supervisor and arrange to repair defects immediately.
If no exterior defects are found:
• Go to “Wheels & Tires, cleaning”

Page 14 of 26
© 2014 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Technical Bulletin
WHEELS & TIRES, CLEANING
• Remove protective cover from wheels (if applicable).
Thick lines of adhesive residue can be removed with general purpose adhesive cleaner.