NHTSA ID Number: 10119497
Manufacturer Communication Number: FL727
TSB/Document Date: 2017-10-15
Summary
FL727 FCCC Motorhome Power Steering.pdf
Daimler Trucks
North America LLC
Recall Campaign
December 2016
FL727A
NHTSA #16V-809
Subject: FCCC Motorhome Power Steering
Hose Routing
Models Affected: Specific Freightliner
Custom Chassis XBR, XCL,
XCM, and XCR chassis equipped with Cummins ISL en gines,
and manufactured January 1, 2016, through October 13, 2016.
General Information
Daimler Trucks North America LLC, on behalf of its wholly owned subsidiary, Freightliner Custom Chassis
Corporation, has decided that a defect that relates to motor vehicle safety exists on the vehicles mentioned
above.
There are approximately 1,827 vehicles involved in this campaign.
On certain motorhome chassis, the high pressure power steering hose may be routed with inadequate
clearance between the hose and a power stud on the starter motor. This may cause the hose to chafe against
the power stud on the starter, potentially leading to arcing and, in addition, may cause loss of fluid, short circuit,
and melting. Electrical arcing in the presence of leaking power steering fluid can increase the risk of a fire.
The high pressure power steering hoses will be rerouted to provide adequate clearance from the starter stud.
Additional Repairs
Dealers must complete all outstanding Recall and Field Service campaigns prior to the sale or delivery of a
vehicle. A Dealer will be liable for any progressive damage that results from its failure to complete campaigns
before sale or delivery of a vehicle.
Owners may be liable for any progressive damage that results from failure to complete campaigns within a
reasonable time after receiving notification.
Work Instructions
Please refer to the attached work instructions. Prior to performing the campaign, check the vehicle for a
completion sticker (Form WAR260).
Replacement Parts
Replacement parts are now available and can be obtained by ordering the part number(s) listed below from
your facing Parts Distribution Center.
If our records show your dealership has ordered any vehicles involved in campaign number FL727, a list of the
customers and vehicle identification numbers will be available in OWL. Please refer to this list when ordering
parts for this recall.
NOTE: Replacement of power steering hoses is per serial, please refer to PartsPro module 535/Steering
Plumbing for part numbers
Table 1 - Replacement Parts for FL727
Campaign Number
FL727A
Part Description
Part Number
Qty.
RAIL CLIP
P-_CLIP
681 997 08 90
23-11357- 012
1 ea
1 ea
BOLT
WASHER
NUT
POWER STEERING HOSE
23-10742-100
23-10900-025
23-13861-104
Per PartsPro/Module 535
Table 1
Page 1
1
1
1
1
ea
ea
ea
ea
Daimler Trucks
North America LLC
Recall Campaign
December 2016
FL727A
NHTSA #16V-809
Removed Parts
U.S. and Canadian Dealers, please follow Warranty Failed Parts Tracking shipping instructions for the
disposition of all removed parts. Export distributors, please destroy removed parts unless otherwise advised.
Labor Allowance
Table 2 - Labor Allowance
Procedure
Time Allowed
(hours)
SRT Code
Damage Code
Inspect power steering hose
0.5
996-0996A
06 - Inspect
Inspect and install P-clip
0.7
996-0996B
12 - Repair
Recall/Campaign
Inspect and replace power steering hose,
install P-clip (1% of vehicles are expected to
need the hose replaced.)
5.3
996-0996C
12 - Repair
Recall/Campaign
Campaign Number
FL727A
Table 2
IMPORTANT: When the Recall has been completed, locate the base completion label in the appropriate location on the vehicle, and attach the red completion sticker provided in the recall kit (Form WAR260). If the vehicle does not have a base completion label, clean a spot on the appropriate location of the vehicle and first
attach the base completion label (Form WAR259). If a recall kit is not required or there is no completion sticker
in the kit, write the recall number on a blank sticker and attach it to the base completion label.
Claims for Credit
You will be reimbursed for your parts, labor, and handling (landed cost for Export Distributors) by submitting
your claim through the Warranty system within 30 days of completing this campaign. Please reference the
following information in OWL:
• Claim type is Recall Campaign.
• In the Campaign field, enter the campaign number and appropriate group (FL727A).
• In the Primary Failed Part Number field, enter 25-FL727-000.
• In the Parts section, enter the appropriate part number(s) as shown in the Replacement Parts Table or
PartsPro if replacement of the power steering hose is required.
• In the Labor section, first enter the appropriate SRT from the Labor Allowance Table. Administrative time
will be included automatically as SRT 939-0010A for 0.4.
• The VMRS Component Code is 015-005-003 and the Cause Code is A1 - Campaign.
• U.S. and Canada -- Reimbursement for Prior Repairs. When a customer asks about reimbursement,
please do the following:
• Accept the documentation of the previous repair.
• Make a brief check of the customer’s paperwork to see if the repair may be eligible for reimbursement. (See the "Copy of Owner Letter" section of this bulletin for reimbursement guidelines for this
recall.)
• Submit an OWL Recall Pre-Approval Request for a decision.
• Attach the documentation to the pre-approval request.
• If approved, submit a based on claim for the pre-approval.
• Reimburse the customer the appropriate amount.
Page 2
Daimler Trucks
North America LLC
Recall Campaign
December 2016
FL727A
NHTSA #16V-809
IMPORTANT: OWL must be viewed prior to performing the recall to ensure the vehicle is involved and the
campaign has not been previously completed. Also, check for a completion sticker prior to beginning work.
For questions, U.S. and Canadian dealers, contact the Warranty Campaigns Department from 7:00 a.m. to 4:00
p.m. Pacific Time, Monday through Friday, via Web inquiry at AccessFreightliner.com / Support / My Tickets
and Submit an Inquiry, or the Customer Assistance Center at (800) 385-4357, after normal business hours, if
you have any questions or need additional information. Export distributors, submit a Web inquiry or contact your
International Service Manager.
U.S.and Canadian Dealers: To return excess kit inventory related to this campaign, U.S. dealers must submit a
Parts Authorization Return (PAR) to the Memphis PDC. Canadian dealers must submit a PAR to their facing
PDC. All kits must be in resalable condition. PAR requests must include the original purchase invoice number.
Export Distributors: Excess inventory is not returnable.
The letter notifying U.S. and Canadian vehicle owners is included for your reference.
Please note that the National Traffic and Motor Vehicle Safety Act, as amended (Title 49, United States Code,
Chapter 301), requires the owner’s vehicle(s) be corrected within a reasonable time after parts are available to
you. The Act states that failure to repair a vehicle within 60 days after tender for repair shall be prima facie
evidence of an unreasonable time. However, circumstances of a particular situation may reduce the 60 day
period. Failure to repair a vehicle within a reasonable time can result in either the obligation to (a) replace the
vehicle with an identical or reasonably equivalent vehicle, without charge, or (b) refund the purchase price in
full, less a reasonable allowance for depreciation. The Act further prohibits dealers from selling a vehicle unless
all outstanding recalls are performed. Any lessor is required to send a copy of the recall notification to the
lessee within 10 days. Any subsequent stage manufacturer is required to forward this notice to its distributors
and retail outlets within five working days.
Page 3
Daimler Trucks
North America LLC
Recall Campaign
December 2016
FL727A
NHTSA #16V-809
Copy of Notice to Owners
Subject: FCCC Motorhome Power Steering
Hose Routing
For the Notice to U.S. Customers: This notice is sent to you in accordance with the National Traffic and Motor
Vehicle Safety Act. For the Notice to Canadian Customers: This notice is sent to you in accordance with the
Canadian Motor Vehicle Safety Act.
Daimler Trucks North America LLC, on behalf of its wholly owned subsidiary, Freightliner Custom Chassis
Corporation, has decided that a defect that relates to motor vehicle safety exists on specific Freightliner Custom
Chassis XBR, XCL, XCM, and XCR chassis equipped with Cummins ISL engines, and manufactured January 1,
2016, through October 13, 2016.
On certain motorhome chassis, the high pressure power steering hose may be routed with inadequate
clearance between the hose and a power stud on the starter motor. This may cause the hose to chafe against
the power stud on the starter, potentially leading to arcing and, in addition, may cause loss of fluid, short circuit,
and melting. Electrical arcing in the presence of leaking power steering fluid can increase the risk of a fire.
The high pressure power steering hoses will be rerouted to provide adequate clearance from the starter stud.
Please contact an authorized Daimler Trucks North America dealer to arrange to have the Recall performed and
to ensure that parts are available at the dealership. To locate an authorized dealer, search online at
www.Daimler-TrucksNorthAmerica.com / Contact Us / Find a Dealer. The Recall will take approximately one half
hour and will be performed at no charge to you.
You may be liable for any progressive damage that results from your failure to complete the Recall within a
reasonable time after receiving notification.
If you do not own the vehicle that corresponds to the identification number(s) which appears on the Recall
Notification, please return the notification to the Warranty Campaigns Department with any information you can
furnish that will assist us in locating the present owner. If you have leased this vehicle, Federal law requires that
you forward this notice to the lessee within 10 days. If you are a subsequent stage manufacturer, Federal law
requires that you forward this notice to your distributors and retail outlets within five working days. If you have
paid to have this recall condition corrected prior to this notice, you may be eligible to receive reimbursement.
Please see the reverse side of this notice for details.
For the Notice to U.S. Customers: If you have questions about this Recall, please contact the Warranty
Campaigns Department at (800) 547-0712, 7:00 a.m. to 4:00 p.m. Pacific Time, Monday through Friday, e-mail
address [email protected], or the Customer Assistance Center at (800) 385-4357 after
normal business hours. If you are not able to have the defect remedied without charge and within a reasonable
time, you may wish to submit a complaint to the Administrator, National Highway Traffic Safety Administration,
1200 New Jersey Avenue, SE., Washington, DC 20590; or call the Vehicle Safety Hotline at (888) 327-4236
(TTY: 800-424-9153); or to http://www.safercar.gov. For the Notice to Canadian Customers: If you have
questions about this Recall, please contact the Warranty Campaigns Department at (800) 547-0712, 7:00 a.m.
to 4:00 p.m. Pacific Time, Monday through Friday, e-mail address [email protected], or
the Customer Assistance Center at (800) 385-4357 after normal business hours.
We regret any inconvenience this action may cause but feel certain you understand our interest in motor vehicle
safety.
WARRANTY CAMPAIGNS DEPARTMENT
Enclosure
Page 4
Daimler Trucks
North America LLC
Recall Campaign
December 2016
FL727A
NHTSA #16V-809
Reimbursement to Customers for Repairs
Performed Prior to Recall
If you have already paid to have this recall condition corrected you may be eligible to receive reimbursement.
Requests for reimbursement may include parts and labor. Reimbursement may be limited to the amount the
repair would have cost if completed by an authorized Daimler Trucks North America LLC dealer. The following
documentation must be presented to your dealer for consideration for reimbursement.
Please provide original or clear copies of all receipts, invoices, and repair orders that show
• The name and address of the person who paid for the repair
• The Vehicle Identification Number (VIN) of the vehicle that was repaired
• What problem occurred, what repair was done, when the repair was done
• Who repaired the vehicle
• The total cost of the repair expense that is being claimed
• Proof of payment for the repair (such as the front and back of a cancelled check or a credit card receipt)
Reimbursement will be made by check from your Daimler Trucks North America LLC dealer.
Please speak with your Daimler Trucks North America LLC authorized dealer concerning this matter.
Page 5
Daimler Trucks
North America LLC
Recall Campaign
December 2016
CAMPAIGN FL727A
NHTSA #16V-809
Work Instructions
Subject: FCCC Motorhome Power Steering
Hose Routing
Models Affected: Specific Freightliner Custom Chassis XBR, XCL,
XCM, and XCR chassis equipped with Cummins ISL engines,
and manufactured January 1, 2016, through October 13, 2016.
Power Steering Hose Inspection
1. Check the base label (Form WAR259) for a completion sticker for FL727 (Form WAR260) indicating this
work has been done. The base label is usually located on the front wall under the dash. If a sticker is present, no work is needed. If there is no sticker, proceed with the next step.
DANGER
When working on the vehicle, shut down the engine and set the parking brake. Before working under
the vehicle, always place jack stands under the frame rails to ensure the vehicle can not drop. Failure to
follow these steps could result in serious personal injury or death.
2. Park the vehicle on a level surface, shut down the engine, and set the parking brake.
3. Using jacks, raise the vehicle.
4. Place jack stands under the frame rails to ensure the vehicle can not drop.
5. Disconnect the battery cables, or if so equipped, turn the battery disconnect switch to the OFF position.
6. Locate the power steering hose (between the pump and the front of the vehicle) then follow the routing to
the starter stud area.
6.1
If the power steering hose is held with a P-clip near the starter stud, no work is needed. See Fig. 1.
Clean a spot on the base label (Form WAR259). Write the recall number, FL727, on a completion
sticker (Form WAR260), and attach it to the base label.
6.2
If the power steering hose is not held with a P-clip near the starter stud and shows no signs of chaffing, cuts, or holes, go to the Power Steering Hose Orientation procedure below.
6.3
If the power steering hose is not held with a P-clip near the starter stud and shows signs of chaffing,
cuts, or holes, go to the Power Steering Hose Replacement procedure on page 7.
Power Steering Hose Orientation
1. Install a rail clip on the top flange of the frame rail, just above the starter.
2. Using a P-clip, bolt, nut, and washer, secure the power steering hose on the rail clip. See Fig. 1. Tighten
the nut 72 lbf·in (813 N·cm).
3. For additional security, install tie bands around the hose to the harness near the frame rail within 18 inches
(46 cm) of the P-clip.
4. Clean a spot on the base label (Form WAR259). Write the recall number, FL727, on a completion sticker
(Form WAR260), and attach it to the base label.
Page 6
Daimler Trucks
North America LLC
Recall Campaign
December 2016
CAMPAIGN FL727A
NHTSA #16V-809
1
2
11/11/2016
3
f462305
1. Rail Clip
2. P-clip
3. Power Steering Hose
Fig. 1, Power Steering Hose with P-Clip (body removed
for clarity)
Power Steering Hose Replacement
NOTE: Replacement of power steering hoses is per serial, please refer to PartsPro module 535/Steering
Plumbing for part numbers.
1. Place a drain pan under the hydraulic pump.
2. At the hydraulic pump, loosen the high-pressure power steering line from the hydraulic pump and let the
fluid drain into the pan.
3. Place a drain pan under the power steering gear.
4. Depending on the vehicle model, loosen the high-pressure power steering line at the bottom of the steering
gear or at the bulkhead fitting, and let the fluid drain into the pan.
5. Remove the high-pressure power steering hose from the power steering pump.
6. At the front of the vehicle, use a male-to-male JIC fitting and attach a new high-pressure hose to the old
hose to pull the new hose through later.
7. Starting at the front of the vehicle, follow the high-pressure hose to the rear, removing all tie straps that secure the hose to the frame rail. Depending on the chassis model, it may be necessary to remove the Aqua
Hot reservoir and position it to the side in order to gain access to the rear compartment.
Page 7
Daimler Trucks
North America LLC
Recall Campaign
December 2016
CAMPAIGN FL727A
NHTSA #16V-809
NOTICE
Do not use any power equipment to remove the hose. Doing so will damage the new hose. If there is
difficulty removing the hose, it may help to route the old hose toward the front of the vehicle over the
air bag.
NOTE: Two technicians are needed to pull the new hose through. Due to the angle of pull on the
hose, it is easier to remove the high-pressure hose from the back of the vehicle. Always pull the hose
in a straight line down the frame rail.
8. At the back of the vehicle, pull the old high-pressure hose through the frame rail until the new hose is in
position and can be attached to the power steering pump.
9. Attach the new high-pressure hose on the power steering pump, and at the steering gear or front bulkhead,
depending on the vehicle model. Tighten the fittings 42 lbf·ft (57 N·m). Ensure that all fittings and clamps
are tight.
10. Install a rail clip and P-clip to hold the power steering hose away from the starter stud. See Power Steering
Hose Orientation on page 6 for instructions, then continue with step 11 below.
11. Connect the battery cables, or if so equipped, turn the battery disconnect switch to the ON position.
IMPORTANT: In order to avoid overflowing the power steering reservoir, fill only to the FULL HOT
mark on the dipstick.
12. Fill the power steering reservoir with Dexron III fluid to the FULL HOT mark on the dipstick. Start the engine, then shut down the engine. Keep repeating the process until air is purged and the fluid level stops
dropping. Avoid running the power steering reservoir empty and foaming the fluid.
13. Once the fluid level stops dropping in the surge tank and the FULL COLD mark is maintained on the dipstick, start the engine and let it run. While the engine is running, slowly turn the steering wheel from full
right to full left, purging any air that is trapped in the steering system.
14. Check all fittings, ensuring there are no leaks.
15. Remove the jack stands.
16. Clean a spot on the base label (Form WAR259). Write the recall number, FL727, on a completion sticker
(Form WAR260), and attach it to the base label.
Page 8
- rv toilet brush: Engineered specifically for RVs, this brush...
- Compact Wall-Mounted Toilet Brush: With its space-saving...
- silicone toilet brush: This brush is designed for thorough...
- Wall-Mounted Toilet Brush for RV Travel: The brush head is...
- Advanced 6-Step Filtration Technology: Discover the...
- Certified Lead-Free: This camping water filter is...
- Access to Pure, Great-Tasting Water: Enjoy clean water...
- Patented Technology & Made in the USA: This in-line water...
- Versatile Applications: Easily attach this multi-purpose...
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: FL727
Replacement Service Bulletin Number:
MFR Communication Date: 2016-12-23
MFR Internal Campaign ID/Software Version:
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: STEERING
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- [Notice] When you receive a used device, it may be a customer return resold by Amazon without inspection. You can exchange it for a new one through Amazon. As this situation is unavoidable, we sincerely apologize. For any issues, contacting us via Amazon's "Messages" is the best way. THINKSCAN 689BT Bidirectional Scan Tool Can Be Used Immediately After It is Turned On, Without Complicated Registration Process, Which is More Convenient & Quick.
- Full Bi-Directional Control & 3000+ Active Tests: Take control and test components like actuators, fuel injectors, relays, and cooling fans in real time. You’ll quickly see if the problem is in the part itself or the control module — saving you hours of guesswork and frustrating trial-and-error.
- Advanced ECU Coding Capabilities: Handle module matching and hidden feature activation with confidence. When you replace an ECU or want to customize settings, this obd2 scanner diagnostic bi directional tool gives you the professional-level capabilities you need without the dealership price tag.
- 34+ Useful Reset and Maintenance Functions: Complete everyday service tasks smoothly with a wide range of helpful reset and maintenance functions. Whether you’re keeping up with regular upkeep or tackling a specific job, this scanner makes maintenance simpler and less stressful for both DIYers and pros.
- Comprehensive Full System Diagnostics: Diagnose every major system — Engine, Transmission
, ABS, SRS, TPMS, and more — all in one place. Finally stop wondering if you’re missing something important; get the full picture and clear codes with ease.
- Top Reasons to Choose the D7S OBD2 Scanner: XTOOL D7S car scan tool, an upgrade of XTOOL D7, offers comprehensive features for automotive technicians, workshops, and DIY enthusiasts 1. Upgraded Hardware: 2+64GB memory, rear camera, intuitive interface, foldable bracket 2. Complete Diagnostics: FCA Autoauth, OE-level all system scan, 39+ maintenance services, 4K+ bidirectional, CANFD/DoIP protocol 3. Advanced Capabilities: ECU coding, PMI functions 4. Wide Compatibility: Support 10,000+ models, covering 99% vehicle brands 5. Multi-language: Available in 22+ languages, No IP Restrictions 6. 3-Year Updates: Save 300 bucks on software updates for the latest features and optimizations
- 2026 Upgraded D7S Car Scanner Features: The newly 2026 D7S V2.0 scanner for car brings exciting features for advanced vehicle diagnostics and enhanced user experience 1. FCA AutoAuth: Now supports FCA SGW module for Chrysler, for Jeep, for Dodge (2018+), for Fiat (2017+), enabling faster vehicle communication without gateway restrictions 2. PMI (Offline ECU Programming): Allows for Ford, for Lincoln, and for Mazda ECU programming for new modules 3. Optimized Diagnostic Report 2.0: Personalized reports with logos and customer info for auto shops. Note: Compatibility varies by cars, please check before order
- Cost-effective ECU Coding Scan Tool for Specific Brands: Enhance your vehicle's performance with XTOOL D7S! This obd2 scanner all systems bidirectional offers advanced capabilities at an affordable price, supports online for BMW, for Benz and offline for BENZ, for MIT, along with PMI functions for Ford, for Mazda, and for Lincoln. Ideal for technicians and DIY enthusiasts, this automotive scanner diagnostic tool optimizes vehicle performance and enhances the driving experience. Note: Not for all cars and modules, please send car VIN to check the compatibility before purchase
- OE All System Diagnostic & 8 Pids Graphing: XTOOL D7S is a comprehensive all system bi directional obd2 scanner that delivers dealer-level diagnostics, completely controlling over your vehicle’s performance and health. This automotive scan tool can read and clear DTCs, view live data and ECU information, retrieve freeze frames, and perform active tests and full obd2 functions. This bi-directional scan tool can can identify your vehicle's make, model, and year information with just one click and show up to 8 PIDs live data with options for CSV viewing, playback, and recording for in-depth analysis. It is easy-to-use for both professionals and beginners, helping pinpoint issues efficiently
- 3 Years Software Update, Value for Money: With 3 years of software updates and 22+ languages(no IP restrictions), XTOOL D7S auto scanner code scanner ensures ongoing compatibility for the latest car models and improved diagnostic functions. This all system vehicle diagnostic scanner comes with a 30-day return policy and a 24-month repair for dependable performance. XTOOL are dedicated to your satisfaction, so enjoy seamless support and lifetime expert assistance. Should you encounter any issues or concerns, don’t hesitate to reach out XTOOL. D7S with newest update with 22 languages freely transfer without authorization, check details from setting-language or from XTOOL
- 【✅Compared to BOSSCOMM IF742, IF745 Offers Full-System Diagnostics】The BOSSCOMM IF745 car diagnostic scanner is an upgraded model of IF742. In addition to supporting all OBD2 Code Reader functions and 6 reset options (ABS/EPB/SAS/BMS/Oil/Throttle), it expands diagnostics from 4 systems (Check Engine/ABS/SRS/Transmission) to vehicle All systems, including Steering, Suspension, and Body Electronics. This provides deeper, more comprehensive diagnostic capabilities.
- 【✨6 Essential Resets: ABS Bleeding, Oil, EPB, SAS, Throttle, BMS】The BOSSCOMM IF745 obd2 scanner diagnostic tool swiftly purges air from brake lines to restore braking sensitivity, fine-tunes maintenance cycles to eliminate false alerts, resolves parking brake issues with one-click control, recalibrates steering sensors for stability, optimizes engine idling/acceleration for smoother performance, and deeply resets battery systems to extend lifespan and range via precise parameter adjustments.❗NOTE: Does NOT support bidirectional control, coding, or programming.
- 【✨Deep Diagnostics for All Vehicle System Modules】Beyond code reading/clearing and ECU information retrieval, our all-in-one data stream feature lets you inspect all current fault codes and their locations across the vehicle’s systems. This vehicle code reader helps you turn off dashboard warning lights and perform a comprehensive self-check of your car at home—no more back-and-forth trips to the repair shop or hefty inspection fees.
- 【✨10 OBD2 Functions】The BOSSCOMM IF745 scan tool’s DTC Lookup instantly translates fault codes into user-friendly explanations, its I/M Readiness feature streamlines emissions testing with a single tap, and Freeze Frame lets you pinpoint the exact moment of a fault for in-depth root-cause diagnosis. Combined with a live data dashboard and advanced diagnostics (O2S, OBMon, EVAP), it delivers comprehensive insights for confident troubleshooting.
- 【✨10,000+ Car Models, AutoVIN, 13 Languages】The BOSSCOMM IF745 vehicle scanner diagnostic tool covers 73+ global car brands and offers support in 13 languages, making it perfect for DIYers, auto mechanics, or as a thoughtful gift. With a single-click AutoVIN feature, it instantly retrieves vehicle serial numbers, streamlining diagnostics for users globally. This adaptable tool balances user-friendliness with precision, catering to both personal and professional requirements.✅Unsure about compatibility? Compatibility will vary on vehicles' model and year, pls reach us via 📧 [email protected] 📧 before purchase.
This product presentation was made with AAWP plugin.