18SP714 – EPA10 DD15/16 Three-Filter Fuel
System to Two-Filter KM59 GEN1 Fuel
System Conversion Service Kit
(P/N: A4710901155)
KIT DESCRIPTION
This service kit includes all necessary parts to convert the DD15/16 three-filter fuel
system to the DD15/16 two-filter KM59 GEN1 fuel system.
KIT CONTENTS
Part No.
A4711530575
A4710909852
A4722030315
A4722003852
A4722030640
A4730702532
A4730702432
A4730702332
A0060705401
A4730702732
A4730702932
A4710700635
A4710780844
A0000701332
A4730700440
A4700780335
A4700780735
A0045405305
A0045405205
A0045405105
05101020
A0009905316
N916016015206
A4700780231
N910105010021
N910105010007

Qty.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
4
1
2
2
6
1

Description
Protective cover
Fuel Filter module
Connecting pipe
Coolant line
Radiator Support Bracket
Needle Return Line
Amplifier Return Line
Pressure Limiting Valve Return Line
Low Pressure Fuel Lines
High Pressure Pump Inlet Line
High Pressure Pump Outlet Line
Doser Fuel Supply Line
High Pressure Flange
High Pressure Fuel Line Kit
Return Line P-clip
Rail Clamps
Rear Rail Clamp
Water In Fuel Sensor Harness
Fuel Temperature Sensor Harness
Low Pressure Pump Outlet Sensor Harness
Zip Ties
Stud Bolt
Coolant Line Clamp
Cylinder Head Fittings
M8x55 Bolt
M8x36 Bolt

18SP714Rev Page 1 of 18

N910105008005
N910105008011
N910105008008
A0019901207
N910105006023
N910105006026
18SP714

11
2
1
6
1
1
1

M8x25 Bolt
M8x20 Bolt
M8x16 Bolt
M6x28 Microencapsulated Bolt
M6x16 bolt
M6x12 Bolt
Installation Instructions

Removal of the Three-Filter Fuel System
Remove as follows:
1. Shut off the engine, apply the parking brake, chock the wheels, and
perform any other applicable safety steps.
2. Disconnect the batteries.
3. Steam clean the engine.

FIRE HAZARD
Do not power wash or steam clean the engine bay in the area of
vehicle electrical components, unless specified by vehicle manuals
or service literature. Power washing/steam cleaning can
permanently damage these components, which could result in fire,
personal injury, or property damage.

4. Remove the fuel feed line from the fuel filter module.
5. Using W470589039100, install J-48710 fuel pressure test kit onto the fuel
feed line at the fuel filter module.
6. Remove the fuel tank fill caps.
7. Using regulator, adjust the system pressure to 345 kPa (50 psi).
8. Pressurize the fuel system for two minutes.
9. Remove J-48710 fuel pressure test kit from the fuel filter module.
10. Install the fuel tank fill caps.
11. Remove the chassis return line from the fuel filter module.
12. Remove the coolant reservoir cap.
13. Open the coolant drain plug (1) located on the left side of the engine block
and attach a hose to the plug.

18SP714Rev Page 2 of 18

NOTICE:
Coolant is a hazardous material and needs to be disposed in an environmentally
responsible manner.
14. Collect the used coolant in a suitable container and if necessary, dispose
of the solution in an environmentally responsible manner according to
state and federal Environmental Protection Agency (EPA)
recommendations.

18SP714Rev Page 3 of 18

15. Close the drain plug. Torque to 30 N•m (22 lb•ft).
16. Disconnect the coolant lines from the front and bottom of the fuel
filter module.
17. Remove the P-clip bolt holding the coolant line to the oil/coolant module.
18. Disconnect the coolant line from the oil/coolant module and remove the
coolant line from the engine. Discard coolant line.
19. Disconnect the water-in-fuel, fuel temperature and low pressure sensor
electrical connectors.
20. If equipped, remove and discard the emergency lubrication line from the
fuel filter module and the high pressure flange.
21. Remove the high pressure pump inlet line from the fuel filter module and
the high pressure flange. Discard the high pressure pump inlet line.
22. Remove the high pressure pump outlet line from the fuel filter module and
the high pressure flange. Discard the high pressure pump outlet line.
23. On V5 three filter fuel systems only, remove the banjo bolt from the low
pressure fuel pump inlet line and both sealing washers.
24. On V5 three filter fuel system only, remove and discard the P-clip bolt
securing the amplifier line to the fuel filter module.
25. Remove the low pressure fuel pump inlet line from the fuel filter module
and the low pressure flange. Discard the low pressure fuel pump inlet line.
26. Remove the low pressure fuel pump outlet line from the fuel filter module
and the low pressure flange. Discard the low pressure fuel pump outlet
line.
27. Remove the needle, amplifier, and pressure limiting valve return lines and
needle return pressure control valve from the fuel filter module.
28. Disconnect the engine wiring harness clip from the fuel filter module.
29. Remove the four bolts securing the fuel filter module to the cylinder block.
Discard the four bolts.
30. Remove fuel filter module from the engine. Discard the fuel filter module.
31. Remove the fuel cooler rubber coupling from the engine block. Discard the
fuel cooler rubber coupling.

18SP714Rev Page 4 of 18

32. Remove the radiator support rod from the radiator support bracket.
Position aside radiator support rod.
33. Remove the radiator support bracket. Discard the radiator support bracket.
34. Disconnect the coolant line from the air compressor and remove the
coolant line from the engine. Discard the coolant line.
35. Remove and discard the low pressure flange and gasket from the high
pressure fuel pump.
36. Remove the doser fuel supply line from the doser block. Discard the doser
fuel supply line.
37. Remove the needle return line from the high pressure flange.
38. Unclip the engine wiring harness from the high pressure flange.
39. Remove and discard the high pressure flange and gasket from the high
pressure fuel pump.
40. Remove and discard the return lines P-clip bolt from the mounting
bracket (1).
a. The graphic below illustrates the DD15/16 engines with a serial
number before 472901S0012796.

b. The graphic below illustrates the DD15/16 engines with a serial
number after 472901S0012796 and all DD13 engines.

18SP714Rev Page 5 of 18

41. Remove and discard the two bolts and P-clips (6) from the mounting
bracket (1).
42. Cover the high pressure fuel pump elements and high pressure fuel rail
feed line sealing areas on the fuel rail with a clean shop towel.
43. Remove and discard the mounting bracket bolts (2) from the intake
manifold and the mounting bracket (1).
NOTE:
When using tool J-48770 to remove the high pressure pump rail feed lines, hold
the high pressure pump fitting with a 24mm wrench.
44. Using tool J-48770, remove the high pressure pump rail feed lines (5) and
vibration dampers (4) from the fuel rail and high pressure fuel pump.
Discard the high pressure pump rail feed lines and vibration dampers.
45. Remove and discard the return lines P-clip (3).
46. Holding the rear needle cylinder head fitting with J-48836, use J-48770 to
remove the needle return line from the rear cylinder head fitting. Discard
the needle return line.
47. Holding the rear amplifier cylinder head fitting with J-48836, use J-48770
to remove the amplifier return line from the rear amplifier cylinder head
fitting. Discard the amplifier return line.
48. Remove and discard the needle and amplifier cylinder head fittings and
sealing washers from the cylinder head.
49. Remove and discard the Pressure Limiting Valve (PLV) line from the fuel
rail.
50. Remove and discard all six rail clamp bolts and three rail clamps from
the engine.

18SP714Rev Page 6 of 18

Installation of the Two-Filter Fuel System
Install as follows:

Bolt Number
1
2
3
4
5
6
7
8
9

Part Number
N910105010021
N910105010007
N910105008005
N910105008011
N910105008008
A4720940155
N910105006023
N910105006026
N000000007957

Size
M8x55
M8x36
M8x25
M8x20
M8x16
M6x28 (micro-encapsulated)
M6x16
M6x12
M6x12 (micro-encapsulated)

1. Remove the water drain bolt (1) for the new fuel filter module.

18SP714Rev Page 7 of 18

Quantity
6
1
11
2
1
6
1
1
4

2. Install the new stud bolt (1) on to the fuel filter module. Torque to
20-22 N·m (15-16 lb·ft).

.
3. Using (bolt number 8), install the new low pressure sensor protective cover
on to the fuel filter module. Torque to 10 N·m (7 lb·ft).
4. Connect the new low pressure pump outlet (LPPO) sensor harness on to the
LPPO sensor.
5. Clip the LPPO sensor harness (1) on to the protective cover.

18SP714Rev Page 8 of 18

6. Install the LPPO sensor harness (1) on to the stud bolt.

18SP714Rev Page 9 of 18

NOTE:
The rear fuel rail clamp has mounting holes for the high pressure fuel lines
mounting bracket.
7. With the arrows pointing upwards, install the three new fuel rail clamps and
six new fuel rail clamp bolts (M6x28 microencapsulated bolt number 6).
Torque to 14 N·m (120 lb·in.).
8. Install the new PLV return line, new sealing washers and new PLV banjo bolt.
Hand-tighten the PLV banjo bolt. Do not torque at this time.
9. Using new sealing washers, install the new needle and amplifier cylinder
head fittings on to the cylinder head. Torque to 55-60 N·m (40-44 lb·ft).
10. Install the new needle and amplifier return lines on to the cylinder head
fittings. Hand tighten the lines. Do not torque at this time.

NOTICE:
DO NOT install any high pressure fuel line bolts and fittings using power
tools. All bolts and fittings MUST be installed using hand tools.

PERSONAL INJURY
All parts provided within this kit must be installed in the proper locations, and
MUST be fastened to the specified torque. Failure to properly torque
hardware/components will result in failure of a high pressure fuel feed line,
resulting in possible fire and/or personal injury.

PERSONAL INJURY
All parts provided within this kit are single-use items and cannot be re-used. Reuse of hardware/component items may result in the failure of a high pressure fuel
line, resulting in possible fire and/or personal injury.

18SP714Rev Page 10 of 18

11. Install the new return lines P-clip on to the return lines.
12. Remove the shop towels covering the high pressure fuel pump elements and
high pressure fuel rail feed line sealing areas on the fuel rail.
13. Clean the sealing area inside the high pressure fuel pump fittings using a
clean, lint-free cloth.

18SP714Rev Page 11 of 18

14. Clean the sealing area inside the high pressure fuel rail using a clean, lintfree cloth.

15. Install the rear high pressure fuel line (3) to the fuel rail and the high pressure
fuel pump. Hand tighten the nuts.
16. Using tool J-48770, torque the rear high pressure fuel line nuts to
40 N·m (30 lb·ft).
17. Install the front high pressure fuel line (3) to the fuel rail and the high pressure
fuel pump. Hand tighten the nuts.
18. Using tool J-48770, torque the front high pressure fuel line nuts to
40 N·m (30 lb·ft).
19. Install the new mounting bracket (2) and two new mounting bracket bolts (4)
(M6x12 microencapsulated bolt number 9) to the fuel rail clamp. Torque to 14
N·m (124 lb·in.).
20. Install the two new P-clips (5) and two new bolts (M6x12 microencapsulated
bolt number 9) to the high pressure fuel rail feed lines (3) and the mounting
bracket (2). Torque to 14 N·m (124 lb·in.).
21. Install a new bolt (1) (M6x16 bolt number 7) on to the return lines P-clip.
Torque to 14 N·m (124 lb·in.).
NOTE:
DO NOT use high pressure fuel lines without new vibration dampers and
new bolts installed.
22. Using J-48770, torque the needle and amplifier return lines on to the cylinder
head fittings at the rear of the cylinder head to 25 N·m (18 lb·ft).
23. Torque the PLV line to the fuel rail to 30-33 N·m (22-24 lb·ft).
24. Clean the high pressure flange mating surface on the high pressure
fuel pump.

18SP714Rev Page 12 of 18

25. Install the new high pressure fuel flange onto the high pressure fuel pump
using M8x25 bolt number 3. Torque to 30 N·m (22 lb·ft).
26. Clip the engine wiring harness on to the high pressure flange.
27. Install the new doser fuel supply line with new sealing washers on to the high
pressure fuel flange and doser block. Torque to 25 N·m (18 lb·ft).
28. Lightly lubricate the new fuel cooler rubber coupling with clean engine coolant
and install the new rubber coupling into the cylinder block.
29. Install the new radiator support bracket on to the engine using M8x55 bolt
number 1 and M8x36 bolt number 2. Torque to 60 N·m (44 lb·ft).
30. Position back radiator support rod and install the radiator support rod on to
the radiator support bracket. Torque to OEM specification.
NOTE: The new radiator support bracket no longer has a mounting point for the
fuel filter module; this will not affect the stability of the fuel filter module.

31. Install the new fuel filter module to the cylinder block with the four new
mounting bolts (M8x55 bolt number 1). Torque to 60 N·m (44 lb·ft).
32. Install and connect the new coolant line on to the air compressor, fuel filter
and oil/coolant filter module.
33. Install the new P-clips on to the coolant line.

18SP714Rev Page 13 of 18

34. Install the mounting bolts (M8x20 bolt number 4) securing coolant line clips to
the fuel filter module and oil/coolant filter module. Torque to 30 N·m (22 lb·ft).
35. Using a zip tie (1), attach the LPPO sensor harness H-clip on to the
coolant line.

36. Using new sealing washers, install the needle, amplifier, and pressure limiting
valve return lines on to the fuel filter module. Torque to 30-33 N·m
(22-24 lb·ft).

18SP714Rev Page 14 of 18

37. Lubricate the new high pressure pump inlet/outlet lines and the low pressure
fuel pump inlet/outlet lines O-rings with a light coat of clean diesel fuel.
38. Install the new low pressure fuel pump inlet and outlet lines on to the fuel filter
module and the high pressure fuel pump using M8x25 bolt number 3. Torque
to 30 N·m (22 lb·ft).
39. Install the new wiring harness bracket on to the fuel filter module using
M8x25 bolt number 3 and low pressure lines using M8x16 bolt number 5.
Torque to 30 N·m (22 lb·ft).
40. Install the new high pressure pump inlet and outlet lines on to the fuel filter
module and the high pressure flange using M8x25 bolt number 3. Torque to
30 N·m (22 lb·ft).

NOTICE:
Wiring harnesses can NOT come into contact with ANY coolant lines or fuel lines.
41. Install and connect the new water-in-fuel and fuel temperature
wiring harnesses.
42. Connect the new LPPO wiring harness.
43. Using a zip tie (1), attach the water-in-fuel wiring harness to the wiring
harness bracket.

44. Using the zip tie (1), attach the fuel temperature and the LPPO wiring
harnesses to the low pressure flange.

18SP714Rev Page 15 of 18

45. Using a zip tie (1), attach the LPPO wiring harness H-clip to the coolant line.

46. Install the chassis fuel feed and return lines on to the fuel filter module. Refer
to OEM procedures.
47. Connect the batteries.
48. With the engine off, fill the cooling system with coolant at a constant minimum
rate (typically 6 to 8 liters per minute) until it reaches the top of the filler neck
or at the "Cold MAX" level.
49. Prime the fuel system with fuel.

PERSONAL INJURY
To avoid injury before starting and running the engine, ensure
the vehicle is parked on a level surface, parking brake is set, and
the wheels are blocked.

18SP714Rev Page 16 of 18

ENGINE EXHAUST
To avoid injury from inhaling engine exhaust, always operate
the engine in a well-ventilated area. Engine exhaust is toxic.

50. Start the engine (no coolant reservoir cap) and idle for one minute. Increase
engine speed slowly to 1000-1200 rpm and hold for one minute. Then reduce
engine speed to idle and cycle up and down between idle and 1000-1200 rpm
for one additional minute.
51. After this three minute burp sequence, stop the engine and add coolant as
required to achieve "Cold FULL" level. If a second top-off is needed, start the
engine and idle the engine for one additional minute.
52. Stop the engine and add coolant as required to achieve the "Cold MAX" level,
and then install the coolant reservoir cap.

PERSONAL INJURY
To avoid injury before starting and running the engine, ensure
the vehicle is parked on a level surface, parking brake is set, and
the wheels are blocked.

ENGINE EXHAUST
To avoid injury from inhaling engine exhaust, always operate
the engine in a well-ventilated area. Engine exhaust is toxic.

18SP714Rev Page 17 of 18

NOTE:
This will eliminate the large pockets of air from the system, although smaller
bubbles will still remain. Normal operation of the vehicle should purge the
remaining air bubbles from the system without any damage. Extremely large
cooling systems (such as in motor homes or luxury coaches) may require
additional time for system deaeration.
53. Start the engine and inspect for leaks.

Specifications are subject to change without notice. Detroit Diesel Corporation is registered to ISO 9001:2008.
Copyright © Detroit Diesel Corporation. All rights reserved. Detroit™ is a brand of Detroit Diesel Corporation,
a Daimler company.
18SP714 1611 As technical advances continue, specifications will change. Printed in U.S.A.

18SP714Rev Page 18 of 18