NHTSA ID Number: 10118442
Manufacturer Communication Number: AHW-17-06
TSB/Document Date: 2017-10-04
Summary
Updated startup instructions for diagnostic interface device.
Service Information
Diagnostic Device Hardware & Windows®
Number: AHW-17-06
Subject: VAS 6154 Diagnostic Interface – Startup Guide
Date: Feb. 08, 2017
Supersedes AHW-16-08 due to updated and additional information
Table of Contents
Page
Section
1.0
Introduction
2
1.1
General Information – MUST READ!
2
1.2
Initial Setup and Accessibility
2
2.0
Startup Instructions
3
2.1
Module Preparation – MUST READ!
3
2.2
WLAN Infrastructure Startup – New Diagnostic Device
4
2.3
WLAN Infrastructure Startup – VAS 6154 Replaces VAS 5054A
4
2.4
USB Startup
5
3.0
Operating Mode Notes
6
3.1
Operating Mode Matrix
6
3.2
LED Indicator Overviews
7
3.3
Switching Between Operating Modes
8
3.4
Web Interface Access
11
3.5
Troubleshooting
12
Notes:
• Please read these instructions carefully and in their entirety before performing the startup
procedures. If you do not understand these instructions, arrange to have a qualified person
perform these procedures.
• Heed all prerequisite requirements and notes, and heed all cross-references to additional
documents posted on ServiceNet.
• Revisions may be issued at any time. Always check ServiceNet for the latest version.
Page 1 of 12
© 2017 Audi
of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual
property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these
materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Service Information
1.0 – Introduction
1.1 – General Information – MUST READ!
This document describes the startup processes required to use new VAS 6154 with diagnostic laptop or
tablet devices with Offboard Diagnostic Information System Service (ODIS Service) diagnostic software.
General user guidelines and tips are included as well.
IMPORTANT!
This guide describes the V AS 6154 WLAN and USB st artup processes on:
New diagnostic devices (diagnostic int erface not yet configured)
and
Existing di agnostic devices w here the V AS 6154 replaces a V AS 5054 A
Please be sure to identify the diagnostic device(s) accordingly, and follow the startup and use
instructions that apply, e.g.: New or Replacement
1.2 – Initial Setup and Accessibility
New VAS 6154 must have their initial setup performed by qualified personnel before the operating modes
and access conditions described below are in effect.
For detailed information refer to Service Information – Diagnostic Device Hardware & Windows
document title:
VAS 6154 Diagnostic Interface – Initial Setup Guide
VAS 6154 Operating Mode
Access Conditions
WLAN Infrastructure
VAS 6154 can be accessed by any diagnostic device
connected to the dealership LAN / WLAN
USB Cable
WLAN Direct
VAS 6154 can be accessed only by diagnostic laptops
and tablets on which a wireless access point network was
established in Windows*
*A wireless access point network can be established between a VAS 6154 and more than one diagnostic device as
necessary. However, to avoid confusion when switching between the WLAN modes, technician users must be
made aware of the devices on which this was or was not established.
Page 2 of 12
© 2017 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual
property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these
materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Service Information
2.0 – Startup Instructions
2.1 – Module Preparation – MUST READ!
Prerequisites:
Technician user is familiar with VAS 6154 features and functions outlined in Service Information –
Diagnostic Device Hardware & Windows document title:
VAS 6154 Diagnostic Interface – Introduction Guide
Initial setup successfully performed by qualified personnel as specified in Service Information –
Diagnostic Device Hardware & Windows document title:
VAS 6154 Diagnostic Interface – Initial Setup Guide
ODIS Service application version 4.0.0 or higher installed on diagnostic device.
Diagnostic device plugged in to power adapter and booted to Windows desktop.
Wireless switch on diagnostic device in ON position, (“Wireless LAN ON” & “802.11a Enabled”).
Diagnostic device connected to dealership WLAN with strong WLAN signal.
ATTENTIO N!
Alw ays check the dealershi p WL AN signal strengt h befor e proceeding.
A w eak WL AN signal w ill result in failed startup attem pts!
1. Plug the WLAN Module -1- into the end of the VAS 6154 module:
-1-
2. Insert assembled module into vehicle Data Link Connector (DLC) and turn on ignition.
3. Wait a moment, and then confirm the status of the three LED indicators as follows:
Green (Power): ON
Blue (Communication): Blinking 1 Hz
Orange (WLAN Infrastructure): ON
4. Proceed with the device-applicable startup:
New Diagnostic Device: Section 2.2 - Page 4
or
VAS 6154 Replaces a VAS 5054A: Section 2.3 - Page 4.
Page 3 of 12
© 2017 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual
property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these
materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Service Information
2.2 – WLAN Infrastructure Startup - New Diagnostic Device
Prerequisites:
VAS 6154 was selected as the applicable Diagnostic Interface during the ODIS Service
installation routine.
VAS 6154 was set to start automatically in WLAN Infrastructure mode during initial setup.
All Startup Preparation prerequisites fulfilled: Section 2.1 – Page 3.
VAS 6154 initially setup for use on the same WLAN as the diagnostic device, with WLAN Infrastructure
mode set to start automatically, will automatically connect to ODIS Service on startup.
1. Start ODIS Service.
2. Wait until the WLAN Infrastructure connection appears as confirmed by the
ODIS Service Connection Mode Indicator - WLAN Infrastructure:
3. Start GFF.
Note:
If ODIS Service does not connect to the VAS 6154 on a strong WLAN signal, VAS 6154 may not
have been selected as the diagnostic interface during the ODIS Service installation routine, or the
initial setup configuration steps for WLAN Infrastructure were not completed properly.
2.3 – WLAN Infrastructure Startup – VAS 6154 Replaces a VAS 5054A
1. Uninstall and reinstall ODIS Service on the existing diagnostic device.
For details, refer to Service Information – ODIS Service document title:
Uninstallation and Reinstallation Instructions
IMPORTANT!
V AS 6154 must be selected as the diagnostic interface dur ing the ODIS
Ser vice application (re)installation routine.
2. When ODIS Service is reinstalled and configured, perform the initial setup. Refer to Service
information – Diagnostic Device Hardware & Windows document title:
VAS 6154 Diagnostic Interface – Initial Setup Guide.
3. When complete, initiate VAS 6154 startup as on a new device using the instructions in Section 2.2
above.
Page 4 of 12
© 2017 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual
property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these
materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Service Information
2.4 – USB Startup
The VAS 6154 USB startup routines mirror that of WLAN Infrastructure mode.
Prerequisite:
Initial USB setup performed and USB drivers installed during initial setup. For details refer to
Service Information – Diagnostic Device Hardware & Windows document title:
VAS 6154 Diagnostic Interface – Initial Setup Guide
1
Remove the VAS 6154 with WLAN module from the vehicle DLC if connected.
2
Depress the side grips on the WLAN module and separate it from the VAS 6154:
Connect the USB Module with cable -1- to the VAS 6154:
-1-
3
Connect USB cable to a USB 2.0 port on the diagnostic device.
4
Insert assembled module into vehicle DLC and turn on ignition.
5
Start ODIS Service.
6
Wait until the USB connection appears as confirmed by the
ODIS Service Connection Mode Indicator – USB Mode:
7
Start GFF.
ATTENTION!
DO NOT connect or disconnect the add-on modules from the V AS 6154
w hen it is pow ered-up and transmitting (LEDs on). Module malfunctions
w ill result! Connections and disconnections of add-on modules must
ONLY take place w hen the 6154 is removed from the base station or
vehicle DLC.
Page 5 of 12
© 2017 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual
property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these
materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Service Information
3.0 – Operating Mode Notes
3.1 – Operating Mode Matrix
Operating Mode:
Use When:
Operation Notes:
• Guided Fault Finding (GFF) is
performed on vehicles in the workshop
environment.
WLAN
Infrastructure
• The diagnostic device is connected to
the dealership WLAN.
This is the primary operating mode for
most GFF procedures.
• Before starting GFF, ensure
that a strong WLAN signal is
received by the diagnostic
device.
• This operating mode is required
for sending diagnostic logs on
test plan completion and
submitting GFF feedback.
• LED Indication: Section 3.2.1 –
Page 10.
• GFF is performed on vehicles outside
out the workshop environment,
WLAN Direct
• The diagnostic device is not
connected to the dealership WLAN.
E.g.: test drive.
This is a secondary operating mode for
specialized GFF procedures.
• Vehicle Software Version management
(SVM) is performed on vehicles in the
workshop environment.
• Sending diagnostic logs and
submitting GFF feedback is
not possible in this mode.
• Logs and feedback must be
sent after switching back to
WLAN Infrastructure mode.
• LED Indication: Section 3.2.2 –
Page 10.
• Until further notice, the USB
operating mode is mandatory
for SVM.
• The diagnostic device is physically
connected to the dealership LAN for
SVM.
Page 6 of 12
© 2017 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual
property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these
materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Service Information
3.2 – LED Indicator Overviews
Notes:
• VAS 6154 automatically run an LED check routine immediately after being plugged in to a power
source. Wait a moment to allow the check to end before evaluating its operation status.
• Until further notice, disregard the fourth (red) LED for DoIP function indications.
3.2.1 – WLAN Infrastructure
LED / Function
Status
ON
Green / Power
Blue / Communication
Blinking 1 Hz
Normal Operation
Error*
OFF
No power supply**
ON
Comm. Established
Blinking - 1 Hz
Blinking - Random
Orange / WLAN Mode
Indication
Comm. Setup In Process
Data Being Transferred
OFF
No connection
ON
WLAN Infrastructure Mode
3.2.1 – WLAN Direct
LED / Function
Status
ON
Green / Power
Blue / Communication
Blinking 1 Hz
Normal Operation
Error*
OFF
No power supply**
ON
Comm. Established
Blinking - 1 Hz
Blinking - Random
Orange / WLAN Mode
Indication
Comm. Setup In Process
Data Being Transferred
OFF
No connection
OFF
WLAN Direct Mode
*Refer to User’s Guide on CD for error indications.
**Check power and ground connections on vehicle Data Link Connector (DLC).
Page 7 of 12
© 2017 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual
property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these
materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Service Information
3.3 – Switching Between Operating Modes
VAS 6154 can be switched between WLAN Infrastructure and WLAN Direct (point-to-point) modes by
pressing the button on the front of the module and selecting the VAS 6154 network from Windows.
WLAN Direct connection steps differ slightly between Windows 7 and Windows 10 devices. Please
heed the following section titles carefully.
Prerequisites:
Initial WLAN Direct setup routine and VAS 6154 network setup manually in Windows as
specified in Service Information – Diagnostic Device Hardware & Windows document title:
VAS 6154 Diagnostic Interface – Initial Setup Guide
Operating system of diagnostic device is known: Either Windows 7 or Windows 10
VAS 6154 plugged in to vehicle DLC and ignition switched on.
A new ODIS Service session is connected to a VAS 6154 running in WLAN Infrastructure mode.
3.3.1 – Switch from WLAN Infrastructure to WLAN Direct – Windows 7
1. Briefly press the button on the front of the module.
The module beeps once.
ODIS Service Connection Mode Indicator change:
2. Click the Windows networking icon in the taskbar:
3. Select /highlight the listed VAS 6154_serial number, and then click Connect:
Note:
The VAS 6154 serial number and various network SSID
illustrated in these routines are examples only!
(cont.)
Page 8 of 12
© 2017 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual
property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these
materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Service Information
4. Click OK:
5. Wait until the WLAN Direct network connection is established.
A delay is normal. Please be patient!
ODIS Service Connection Mode Indicator change:
6. Click the Windows networking icon in the taskbar and
confirm direct network connection with VAS 6154:
3.3.2 – Switch from WLAN Infrastructure to WLAN Direct – Windows 10
1. Briefly press the button on the front of the module.
The module beeps once.
ODIS Service Connection Mode Indicator change:
2. Click the Windows networking icon in the taskbar:
(cont.)
Page 9 of 12
© 2017 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual
property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these
materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Service Information
3. Double-click the VAS 6154 network
Note:
4. Click Connect:
The VAS 6154 serial number and various
network SSID illustrated in these routines
are examples only!
5. Click OK:
Wait until the WLAN Direct network connection is established.
6. A delay is normal. Please be patient!
7. ODIS Service Connection Mode Indicator change:
8. Click the Windows networking icon in the taskbar and
confirm direct network connection with VAS 6154 (top of list).
3.3.3 – Switch from WLAN Direct to WLAN Infrastructure – Windows 7 and Windows 10
The module automatically reconnects to the dealership WLAN and VAS 6154 WLAN Infrastructure modes.
1. Briefly press the button on the front of the module.
The module beeps twice.
2. Click OK:
(cont.)
Page 10 of 12
© 2017 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual
property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these
materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Service Information
3. Wait while the ODIS Service Connection Mode Indicator automatically cycles from:
WLAN Direct
WLAN Reconnect
WLAN Infrastructure Mode Active
3.4 – Web Interface Access
The web interface used to perform the VAS 6154 initial setup can be accessed during active
communication between the VAS 6154 and ODIS Service. This enables minor changes to be made “ondemand” without the base station.
Common setup changes are activating or deactivating the VAS 6154 Power-Saving, Auto-Off and
Warning Buzzer features. If needed, the network SSIDs, encryption keys, unique name assigned to the
module and module ID can also be read directly from the web interface.
To access the VAS 6154 web interface during an active ODIS Service session, proceed as follows:
1. From the ODIS Service operating mode menu, select Extras, and then select Diagnostic Interface.
2. Select VCI Configuration:
3. Select the desired Main Category (top menu) and Subcategory (left margin menu)
4. Perform the necessary changes, “Accept” the changes, and then click OK to close the interface.
For detailed additional information on the web interface and the various settings, refer to the User’s Guide
on CD.
Page 11 of 12
© 2017 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual
property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these
materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Service Information
3.5 – Troubleshooting
Troubleshooting procedures and error code indications for qualified personnel are covered in detail in the
User’s Guide on CD.
Refer to User’s Guide on CD:
•
Troubleshooting - Section 5.2 – from Page 76
•
Error Message indications - Appendix – from Page 90.
Page 12 of 12
© 2017 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual
property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these
materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
- 💯【Conta.ct us for Support Directly】If you met any...
- 🔥🔥🔥【2026 AUTEL FLAGSHIP MK900BT MK900-BT, NEW...
- 🚗【3000+ ACTIVE TESTS (50➡3000+), SAME AS MS...
- 🚗【40+ HOT SERVICES FOR 150 MAKES (28+➡40+)】Full...
- 🚗【OE ALL SYSTEM DIAGNOSE, AUTO SCAN 2.0: SCAN LICENSE...
- 【TURN OFF CEL】 This AL319 car scanner diagnostic tool...
- 【EXTENSIVE APPLICATION】 Autel AL319 Compatible with...
- 【FOR END USER & DIYERS】 This error code reader AL319 is...
- 【USER-FRIENDLY DESIGN】 This OBD2 scanner and check...
- 【HIGH-QUALITY SERVICES】 12 months war.ranty from the...
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: AHW-17-06
Replacement Service Bulletin Number:
MFR Communication Date: 2017-02-08
MFR Internal Campaign ID/Software Version:
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: EQUIPMENT
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- [Notice] When you receive a used device, it may be a customer return resold by Amazon without inspection. You can exchange it for a new one through Amazon. As this situation is unavoidable, we sincerely apologize. For any issues, contacting us via Amazon's "Messages" is the best way. THINKSCAN 689BT Bidirectional Scan Tool Can Be Used Immediately After It is Turned On, Without Complicated Registration Process, Which is More Convenient & Quick.
- Full Bi-Directional Control & 3000+ Active Tests: Take control and test components like actuators, fuel injectors, relays, and cooling fans in real time. You’ll quickly see if the problem is in the part itself or the control module — saving you hours of guesswork and frustrating trial-and-error.
- Advanced ECU Coding Capabilities: Handle module matching and hidden feature activation with confidence. When you replace an ECU or want to customize settings, this obd2 scanner diagnostic bi directional tool gives you the professional-level capabilities you need without the dealership price tag.
- 34+ Useful Reset and Maintenance Functions: Complete everyday service tasks smoothly with a wide range of helpful reset and maintenance functions. Whether you’re keeping up with regular upkeep or tackling a specific job, this scanner makes maintenance simpler and less stressful for both DIYers and pros.
- Comprehensive Full System Diagnostics: Diagnose every major system — Engine, Transmission, ABS, SRS, TPMS, and more — all in one place. Finally stop wondering if you’re missing something important; get the full picture and clear codes with ease.
- Top Reasons to Choose the D7S OBD2 Scanner: XTOOL D7S car scan tool, an upgrade of XTOOL D7, offers comprehensive features for automotive technicians, workshops, and DIY enthusiasts 1. Upgraded Hardware: 2+64GB memory, rear camera, intuitive interface, foldable bracket 2. Complete Diagnostics: FCA
Autoauth, OE-level all system scan, 39+ maintenance services, 4K+ bidirectional, CANFD/DoIP protocol 3. Advanced Capabilities: ECU c0ding, PMI functions 4. Wide Compatibility: Support 10,000+ models, covering 99% vehicle brands 5. Multi-language: Available in 22+ languages, No IP Restrictions 6. 3-Year Updates: Save 300 bucks on software updates for the latest features and optimizations - 2026 Upgraded D7S Car Scanner Features: The newly 2026 D7S V2.0 scanner for car brings exciting features for advanced vehicle diagnostics and enhanced user experience 1. FCA AutoAuth: Now supports FCA SGW module for Chrysler, for Jeep, for Dodge (2018+), for Fiat (2017+), enabling faster vehicle communication without gateway restrictions 2. PMI (Offline ECU Pr0gramming): Allows for Ford, for Lincoln, and for Mazda ECU pr0gramming for new modules 3. Optimized Diagnostic Report 2.0: Personalized reports with logos and customer info for auto shops. Note: Compatibility varies by cars, please check before order
- 39+ Services/Resets/Adaptations/Relearns/Calibrations: XTOOL D7S full system car scanner diagnostic tool tackles 99% of common car issues through its 36+ special functions, including Oil Reset, EPB, SAS, BMS, Throttle Reset, Injector C0ding, ABS Bleed, TPMS Reset, Power Balance, etc and also covers specific-vehicle functions like Crank Sensor Relearn, ABS Initialization, Cylinder Power Balance, Fuel Trim Reset, Idle Relearn etc. This car diagnostic scanner enhances efficiency, making repairs and maintenance hassle-free. Tip: DO NOT for All vehicles, please check compatibility first
- Cost-effective ECU C0ding Scan Tool for Specific Brands: Enhance your vehicle's performance with XTOOL D7S! This obd2 scanner all systems bidirectional offers advanced capabilities at an affordable price, supports online for BMW, for Benz and offline for BENZ, for MIT, along with PMI functions for Ford, for Mazda, and for Lincoln. Ideal for technicians and DIY enthusiasts, this automotive scanner diagnostic tool optimizes vehicle performance and enhances the driving experience. Note: Not for all cars and modules, please send car VIN to check the compatibility before purchase
- OE All System Diagnostic & 8 Pids Graphing: XTOOL D7S is a comprehensive all system bi directional obd2 scanner that delivers dealer-level diagnostics, completely controlling over your vehicle’s performance and health. This automotive scan tool can read and clear DTCs, view live data and ECU information, retrieve freeze frames, and perform active tests and full obd2 functions. This bi-directional scan tool can can identify your vehicle's make, model, and year information with just one click and show up to 8 PIDs live data with options for CSV viewing, playback, and recording for in-depth analysis. It is easy-to-use for both professionals and beginners, helping pinpoint issues efficiently
- 【✅Compared to BOSSCOMM IF742, IF745 Offers Full-System Diagnostics】The BOSSCOMM IF745 car diagnostic scanner is an upgraded model of IF742. In addition to supporting all OBD2 Code Reader functions and 6 reset options (ABS/EPB/SAS/BMS/Oil/Throttle), it expands diagnostics from 4 systems (Check Engine/ABS/SRS/Transmission) to vehicle All systems, including Steering, Suspension, and Body Electronics. This provides deeper, more comprehensive diagnostic capabilities.
- 【✨10 OBD2 Functions】The BOSSCOMM IF745 scan tool’s DTC Lookup instantly translates fault codes into user-friendly explanations, its I/M Readiness feature streamlines emissions testing with a single tap, and Freeze Frame lets you pinpoint the exact moment of a fault for in-depth root-cause diagnosis. Combined with a live data dashboard and advanced diagnostics (O2S, OBMon, EVAP), it delivers comprehensive insights for confident troubleshooting.
- 【✨Deep Diagnostics for All Vehicle System Modules】Beyond code reading/clearing and ECU information retrieval, our all-in-one data stream feature lets you inspect all current fault codes and their locations across the vehicle’s systems. This vehicle code reader helps you turn off dashboard warning lights and perform a comprehensive self-check of your car at home—no more back-and-forth trips to the repair shop or hefty inspection fees.
- 【✨6 Essential Resets: ABS Bleeding, Oil, EPB, SAS, Throttle, BMS】The BOSSCOMM IF745 obd2 scanner diagnostic tool swiftly purges air from brake lines to restore braking sensitivity, fine-tunes maintenance cycles to eliminate false alerts, resolves parking brake issues with one-click control, recalibrates steering sensors for stability, optimizes engine idling/acceleration for smoother performance, and deeply resets battery systems to extend lifespan and range via precise parameter adjustments.❗NOTE: Does NOT support bidirectional control, coding, or programming.
- 【✨10,000+ Car Models, AutoVIN, 13 Languages】The BOSSCOMM IF745 vehicle scanner diagnostic tool covers 73+ global car brands and offers support in 13 languages, making it perfect for DIYers, auto mechanics, or as a thoughtful gift. With a single-click AutoVIN feature, it instantly retrieves vehicle serial numbers, streamlining diagnostics for users globally. This adaptable tool balances user-friendliness with precision, catering to both personal and professional requirements.✅Unsure about compatibility? Compatibility will vary on vehicles' model and year, pls reach us via 📧 [email protected] 📧 before purchase.
This product presentation was made with AAWP plugin.