Ferrari North America
Technical Information
Model Type:
Model Year:
Subject:

Date:
Bulletin #:
Campaign #:
Supersedes:
Section:

June 2017
2421
10

GTC4 Lusso
All
Pre-Delivery Inspection – PDI procedures

Please find enclosed the procedures and list of inspections to be performed at all times
before the vehicle is delivered to the customer.
The following procedures must be performed exactly as indicated and in the order given,
providing the factory with the information requested.

- IMPORTANT This Pre-Delivery Inspection (PDI) procedure may only be performed with a
PC-Tester DEIS updated to at least the following software version (or
subsequent release):
- Module 0

Portal and Troubleshooting

47

- Module 1

DEIS Diagnostic software

76

- Module 2

Technical Documentation

12

- Module 3

Tools

7

Check the software number and, if necessary, update your DEIS Tester
immediately.
After updating the DEIS, the first vehicle diagnostic cycle must be performed
using a cable connection.

© 2017 Ferrari North America, Inc.
Technical Department
www.ferrariusa.com

All rights reserved. Reproduction or translation in
whole or in part is not permitted without
authorization from the publisher. Printed in USA

Ferrari North America
Procedure.
1.

Visually inspect condition of vehicle paintwork; repair if necessary (use the specific
“Bodywork defects” form annexed on page 8).

2.

If disconnected, connect the negative pole of the battery and reset the vehicle autoadaptive parameters (as described in paragraph F2.01 of the Workshop Manual).

3.

Activate Key-ON state (as described in paragraph E5.06 of the Workshop Manual), and
check which letter is shown on the DOT MATRIX display:
- If letter “P” (Park Lock) is on the display, go to point 5.
- If letter “N” (Neutral) is on the display, go to point 4.

4.

Re-enable the Park Lock – Gearbox lock device (as described in paragraph E5.10 of the
Workshop Manual).

5.

Remove the engine compartment cosmetic shields (as described in paragraph E3.14 of
the Workshop Manual); Perform the “Battery Certification” procedure (TI 2079 /
2230), and compile the relative form. If necessary, remove the battery from the vehicle
and charge using the “SLOW charge ” procedure (TI 2078).

6.

Using the DEIS tester, disable the “Logistic Mode” function with diagnostic cycle “150
Complete Logistic Mode” on the NBC ECU (Body Computer Node).

7.

Test the keys and the anti-theft system.

8.

Check that the daytime lights work correctly (depending on market).

9.

Check that the low beam lights work correctly: also check function of the AFS system
(adaptive front lights - if applicable) by turning the steering wheel.

10. Check function of the front and rear obstacle clearance lifts (if applicable): also check
function of the AFS system (adaptive front lights - if applicable). With the
car raised, the height of the headlight beam must be the same as with the car lowered.
11. Check that the high beam lights work correctly.
12. Check that the brake lights work correctly.
2
© 2017 Ferrari North America, Inc.
Technical Department
www.ferrariusa.com

TI-2421

All rights reserved. Reproduction or translation in
whole or in part is not permitted without
authorization from the publisher. Printed in USA

Ferrari North America
13. Check that turn indicators work correctly.
14. Check that door lights, vehicle interior lights and luggage compartment light work
correctly.
15. Check that the door button, center console, cabin and glove compartment button
lights are working.
16. Test the horn.
17. Check that the power windows work correctly.
18. Check that the windshield and headlight wipers work correctly.
19. Check that the steering adjustment mechanism works correctly.
20. Check that the driver and passenger side electric seats, also testing memory storage
function.
21. Check function of electric parking brake (EPB); test manual and automatic modes.
22. Check function of HI-FI / navigation system (see point 35); set the relative roadside
assistance numbers for your market.
23. Check coolant level and top up if necessary.
24. Check power steering fluid level and top up if necessary.
25. Check brake fluid level and top up if necessary.
26. Check headlight washer/windshield washer fluid level and top up if necessary.
27. Check tire pressure / TPMS system calibration pressure.
28. Check tightness of wheel studs with a torque wrench rechecking the final tightening
torque (as described in paragraph D2.01 of the Workshop Manual).
29. Check that the tow hook is fitted correctly.
3
© 2017 Ferrari North America, Inc.
Technical Department
www.ferrariusa.com

TI-2421

All rights reserved. Reproduction or translation in
whole or in part is not permitted without
authorization from the publisher. Printed in USA

Ferrari North America
Start the engine (as described in paragraph E5.06 of the Workshop Manual),
and perform the following:
30. Perform static function test of AC system.
31. Test function of electric rear view mirrors.
32. Select reverse:
- check that the angle of the RH rear view mirror(or the LH mirror on RHD
cars) adjusts automatically;
- check function of the internal electrochromic mirror and the
electrochromic RH and LH rear view mirrors.
33. Check function of front and rear parking sensors; check rear and front cameras (if
applicable).
34. Using the DEIS tester, perform the “Cancel all DTCs from all ECUs” procedure from
the “Vehicle functions” menu.
Test drive.
35. Check function of navigation system (if applicable); Set route before starting.
36. Test drive the vehicle (approx. 20 minutes).
37. Check function of Stop&Start system (if applicable).
38. While driving, check that the “Suspension damping decoupling” button and
“Manettino” dial on the steering wheel work correctly.
39. Check function of AC system while driving (dynamic test).
40. For USA/CND Version only. Take the vehicle into a location with a clear view of the
sky, set the SiriusXM receiver to preview channel 1, and listen to the audio (note that
the preview channel is only available on unactivated SDARS units with no subscription).

4
© 2017 Ferrari North America, Inc.
Technical Department
www.ferrariusa.com

TI-2421

All rights reserved. Reproduction or translation in
whole or in part is not permitted without
authorization from the publisher. Printed in USA

Ferrari North America
Return to workshop.
41. Check the engine oil level (engine warm and at idle speed) and top up if necessary (as
described in paragraph A3.01 of the Workshop Manual).
42. With the DEIS tester, check that the VIN number read with the tester matches the VIN
number of the vehicle; if necessary, the VIN number read with the tester may be
modified using the “100 VIN Writing” diagnostic function (password-protected) on
the NCM ECUs (RH and LH engine control nodes).
43. Check and cancel the errors on all ECUs.
44. Enter the warranty start date (Check that the language setting on the TFT display is
correct).
45. Disconnect the battery , wait 30” and reconnect (as described in paragraph F2.01 of
the Workshop Manual). Restore the self-adaptive vehicle parameters (as described in
paragraph F2.01 of the Workshop Manual).
46. Perform the “SCAN OUT” procedure from the “Vehicle functions” menu with the
DEIS tester before carrying out any further diagnostic operations.
47. Remove the aerodynamic undertray from the vehicle (as described in paragraph E3.13
of the Workshop Manual).
48. Visually check for coolant and/or oil leaks in the underbody area and engine
compartment.
49. Visually inspect engine compartment lines.
50. Visually inspect engine compartment wiring harnesses.
51. Visually inspect underbody lines.
52. Visually inspect exhaust pipe.
53. Visually inspect fuel tank.
54. Visually check correct assembly/fastening of: Suspension components, steering box and
axle shaft flanges.
5
© 2017 Ferrari North America, Inc.
Technical Department
www.ferrariusa.com

TI-2421

All rights reserved. Reproduction or translation in
whole or in part is not permitted without
authorization from the publisher. Printed in USA

Ferrari North America
55. Visually check correct assembly/fastening of: Vehicle ground, engine ground on chassis
ground and gearbox earth on chassis.
56. Visually inspect condition of brake pads and discs (DO NOT remove wheels).
57. Check condition of tires and wheels.
58. Refit complete aerodynamic undertray complete and cosmetic engine compartment
shields (as described in paragraph E3.13 and E3.14 of the Workshop Manual).
59. Check function of doors and lid locks; adjust if necessary.
60. Check function of fuel filler flap emergency release; adjust if necessary.
61. Visually inspect condition of leather upholstery; repair if necessary
62. Thoroughly clean interior and wash car.
63. Ensure that the vehicle is delivered complete with the following:
Identification and Type Approval plates
License plate holder
Toolkit
on-board documentation (Owner's Manual, Quick Reference Guide, Warranty
Booklet, Safety Device Booklet and Battery Conditioner Card), second vehicle key
and Code Card, and any material related to options.

6
© 2017 Ferrari North America, Inc.
Technical Department
www.ferrariusa.com

TI-2421

All rights reserved. Reproduction or translation in
whole or in part is not permitted without
authorization from the publisher. Printed in USA

Ferrari North America
- IMPORTANT Confirm that the operations listed above have been carried out correctly
with the “Pre-Delivery Inspection - PDI” form (enclosed on pages 6 and 7),
compiled in full and signed by the Aftersales Manager of your Service
Centre.

After completing an inspection, ALWAYS open a ROL (Red On Line),
indicating “PDI Form Info” as the cause, and attach the fully completed
“PDI Pre-Delivery Inspection” form, together with the parameter and error
printout files requested in points 34, and 46, and the “Battery state
certification” form (TI 2079 / 2230). The procedure for “Testing zero load
electric absorption” is given in paragraph F2.13 of the Workshop Manual).

You will also be required to open a separate individual ROL with the
description “PDI Fault Info” for each fault encountered during the
inspection procedure, indicating the respective operation number as cited
in the “PDI Pre-Delivery Inspection” form; Attach all documentation
necessary, including photographs if needed.

Thank you for your co-operation

7
© 2017 Ferrari North America, Inc.
Technical Department
www.ferrariusa.com

TI-2421

All rights reserved. Reproduction or translation in
whole or in part is not permitted without
authorization from the publisher. Printed in USA

Pre-Delivery Inspection - PDI form
Model

Updated on
June 2017

Chassis number:

Dossier creation date:

Job order No.:
Notes:

Description of inspection / operation:
1. - Condition of vehicle paintwork.
2. - Connect battery and reset vehicle parameters.
3. - Check Park Lock device.
4. - Reset Park Lock device.
5. - “Battery Certification” procedure.
6. - Disable “Logistic Mode”.
7. - Test keys, etc.
8. - Daytime running lights.
9. - Low beams.
10. - Check vehicle front lift system (if applicable).
11. - High beams.
12. - Stop lights.
13. - Turn indicators.
14. - Door, vehicle interior and luggage compartment lights.
15. - Door, dashboard and glove compartment button lights.
16. - Horn.
17. - Power windows.
18. - Windshield and headlight wipers.
19. - Steering wheel adjustment
20. - Seats / Electric seats; memory storage function.
21. - Electric parking brake (EPB); manual/auto.
22. - HI-FI system / navigation system (see point 35).
23. - Coolant level.
24. - Power steering oil level.
25. - Braking system fluid level.
26. - Windshield washer/headlight washer fluid level.
27. - Tire pressure / calibrated pressure on TPMS.
28. - Tightening of wheel stud bolts.
29. - Tow hook.
30. - * Air conditioning and heating system (static test).
31. - *Electric rear-view mirrors.
32. - *RH or LH rear view mirror – with reverse selected.
33. - *Parking sensors.
34. - Cancel all DTCs from all ECUs.
35. - Navigation system: Set route.
36. - Test drive (20 min.).
37. - Stop&Start (functional test) (if applicable).
(*) With engine running

Performed
OK

Performed
NOT OK













































































R.O.L. N°
(if NOT OK)

Pre-Delivery Inspection - PDI form
Model

Updated on
June 2017

Description of inspection / operation:

Performed
OK

Performed
NOT OK





























































38. - Suspension damping decouple button and “Manettino”.
39. - Air conditioning and heating system (dynamic test).
40. - for USA / CND ONLY _ SDARS preview Channel Test.
41. - Engine oil level (warm engine – at idle speed).
42. - Verify VIN from NCM parameters.
43. - Delete ECU errors.
44. - Enter warranty start date.
45. - Disconnect and reconnect the battery.
46. - Perform SCAN OUT procedure.
47. - Remove aerodynamic floor.
48. - Water and/or oil leaks in vehicle underbody .
49. - Engine compartment lines.
50. - Engine compartment wiring.
51. - Underbody lines.
52. - Exhaust pipe.
53. - Fuel tank.
54. - Visual inspection: Suspension components, etc.
55. - Visual inspection of earth connections: vehicle/engine and
gearbox earth on chassis.
56. - Condition of brake pads and discs (DO NOT remove
wheels).
57. - Condition of tyres and wheel rims.
58. - Refit flat bottom and the engine compartment panels.
59. - Door and lid locks.
60. - Petrol filler flap emergency opening.
61. - Condition of vehicle's leather upholstery.
62. - Clean interior and wash car.
63. - Material provided with vehicle: Toolkit, etc.

R.O.L. N°
(if NOT OK)

Task performed by (Dealer):

Technical Manager:
First name
(block letters)

Surname
(block letters)

Company stamp

Full signature
Vehicle delivery date: