Bulletin No.: PIP5216D
Date: Dec-2015

Subject:

Engine Replacement Recommendations HFV6 Gen 1 Only

Models:

2008-2016 Buick Enclave
2010-2016 Buick LaCrosse
2013-2015 Cadillac ATS
2016 Cadillac ATS-V
2007-2015 Cadillac CTS
2014-2016 Cadillac CTS V-Sport
2007-2010 Cadillac STS
2007-2016 Cadillac SRX
2013-2016 Cadillac XTS
2010-2015 Chevrolet Camaro
2012-2013 Chevrolet Caprice PPV
2012-2015 Chevrolet Captiva Sport
2015-2016 Chevrolet Colorado
2008-2016 Chevrolet Equinox
2012-2016 Chevrolet Impala Vin W
2014-2016 Chevrolet Impala Vin 1 (including Bi-fuel)
2008-2012 Chevrolet Malibu
2009-2016 Chevrolet Traverse
2007-2016 GMC Acadia
2015-2016 GMC Canyon
2010-2016 GMC Terrain
2008-2010 Pontiac G6
2008-2009 Pontiac G8
2008-2009 Pontiac Torrent
2007-2009 Saturn Aura
2008-2010 Saturn Vue
2007-2010 Saturn Outlook
Equipped with HFV6 Gen 1 engines including RPO codes LAU, LF1, LF3, LF4, LFR, LFW, LFX, LLT, LP1,
and LY7

This PI was superseded to update Administrative Details. Please discard PIP5216C.

1

The following diagnosis might be helpful if the vehicle exhibits the symptom(s) described in this PI.

Condition/Concern
If a vehicle comes into the dealership with a knock noise, seized engine, lower end squeak or squeal or any condition that you suspect a rod or main bearing
failure.
First, verify there is metal in the engine oil caused by BEARING DAMAGE / debris by removing the oil pan.

If Due To BEARING FAILURE when completing diagnosis, and deciding whether to replace the engine or repair it, complete the following before making that
determination.

Recommendation/Instructions
1.

Inspect the oil control solenoids for metal debris. This shows the oil filter is in by-pass and unfiltered oil with bearing debris was pumped into the oil
lubrication gallies, throughout the engine

2

2.

Inspect for damage to the cam caps Journals and camshaft journals on the heads (obvious signs of metal through the cap).

3.

Inspect the timing chain idler sprockets for stiffness when turning. (Should turn smooth and free)

3

Any Of These 3 instances would be cause to replace the engine instead of repair.
Note: If this is the case, then a call to TAC is NOT required prior to engine replacement.
At this point you should clearly document your findings on your repair order, fill out the cost worksheet, and call PQC only if required for your dealer.
Keep in mind that a repair and then replacement will usually be cause for additional inspection and scrutiny that could result in more questioning about the repair
methods.
HFV6 engines are scheduled to be returned to the WPC for inspection to verify the concern, as well as the information provided in the repair order to support
the engine replacement.

Warranty Information
For vehicles repaired under warranty use:
Labor Operation

Description

Labor Time

4067490

Engine Replacement

Use Published Labor Operation Time

Please follow this diagnostic or repair process thoroughly and complete each step. If the condition exhibited is resolved without completing every step, the
remaining steps do not need to be performed.
GM bulletins are intended for use by professional technicians, NOT a "do-it-yourselfer". They are written to inform these technicians of conditions that may
occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained technicians have the equipment, tools,
safety instructions, and know-how to do a job properly and safely. If a condition is described, DO NOT assume that the bulletin applies to your vehicle, or that
your vehicle will have that condition. See your GM dealer for information on whether your vehicle may benefit from the information.
4

WE SUPPORT VOLUNTARY TECHNICIAN CERTIFICATION

5