NHTSA ID Number: 10109316
Manufacturer Communication Number: 122-Y5V9G-06
TSB/Document Date: 2017-08-01
Summary
Concerns: Body seals and individual rubber sleeves/stoppers This is to inform you of a voluntary Workshop Campaign on the above-mentioned vehicles. There is the possibility that certain areas of the body were not sealed correctly on the affected vehicles. As a result, water can leak into the luggage compartment or passenger compartment.
Workshop Manual ’536919 Removing and installing
rear wheel housing liner - section on "Installing"’.
6
Install rear roof trim panel ⇒ Workshop Manual ’708519 Removing and installing rear roof trim panel
- section on "Installing"’.
Figure 46
Subsequent work for body front section
7
Re-fit foam seal ⇒ Figure 47 -1- between the right
wing ⇒ Figure 47 -2- and longitudinal member for
the wheel housing upper section ⇒ Figure 47 -3-.
2
Stick on the foam seal ⇒ Figure 47 -1- using
double-sided adhesive tape if necessary.
8
1
Install battery console holder.
3
Figure 47
Jul 19, 2012
Page 28 of 34
AfterSales
2012© Porsche
Cars North America, Inc.
8.1
5
Service
Technical Information
37/12 ENU
Re-fit foam seal ⇒ Figure 48 -1- between
the body and fuel tank ⇒ Figure 48 -2- and
stick it on using double-sided adhesive tape if
necessary.
WC25
1
2
Figure 48
8.2
Clip in brake lines ⇒ Figure 49 -1- using
the retaining clips ⇒ Figure 49 -2- at the
bodyshell mounting ⇒ Figure 49 -arrows-.
8.3
Clip in cable clip on the battery console
holder.
1
2
Figure 49
8.4
Position battery console holder at the
bodyshell mounting and secure with
the fastening screws ⇒ Figure 50 -1-.
Tightening torque 23 Nm (17 ftlb.)
1
Figure 50
2012© Porsche Cars North America, Inc.
AfterSales
Jul 19, 2012
Page 29 of 34
5
Service
WC25
ENU
Technical Information
37/12
8.5
Secure the vacuum line.
8.5.1
Plug in vacuum line ⇒ Figure 51
-arrow A- until it engages securely.
8.5.2
Clip in vacuum line at the battery
console holder ⇒ Figure 51 -arrow
B-.
B
A
Figure 51
9
Install battery console.
9.1
Plug in connector for the fuel pump control
unit at the underside of the battery console ⇒
Figure 52 -1- until it engages securely.
9.2
Tighten fastening screws ⇒ Figure 52
-2- for the battery console to the specified
tightening torque. Tightening torque
23 Nm (17 ftlb.)
1
2
10 Install wiper linkage ⇒ Workshop Manual ’921919
Removing and installing wiper linkage - section on
"Installing"’.
Figure 52
11 Install front apron ⇒ Workshop Manual ’631519 Removing and installing front apron - section on
"Installing"’.
12 Install headlights at the left and right ⇒ Workshop Manual ’941519 Removing and installing headlights - section on "Installing"’.
13 Install battery ⇒ Workshop Manual ’270619 Removing and installing battery - section on "Installing"’.
14 Install front luggage compartment trim panel ⇒ Workshop Manual ’700519 Removing and installing
front luggage compartment trim panel - section on "Installing"’.
15 Install front trim at the left and right (wing flange) ⇒ Workshop Manual ’700219 Removing and
installing front trim (wing flange) - section on "Installing"’.
16 Enter the workshop campaign in the Warranty and Maintenance booklet.
Jul 19, 2012
Page 30 of 34
AfterSales
2012© Porsche Cars North America, Inc.
Service
Technical Information
37/12 ENU
WC25
5
Attachment "B"
Claim Submission - Workshop Campaign WC25
Warranty claims should be submitted via WWS/PQIS.
Open campaigns may be checked by using either the PIWIS Vehicle Information system or through PQIS
Job Creation.
Labor, parts, and sublet will be automatically inserted when Technician is selected in WWS/PQIS.
Applies to Scope 1 Only
— Labor will be inserted automatically when the technician is selected in WWS. If necessary, the required
part numbers will need to be manually entered into WWS by the dealer administrator.
— The sublet (miscellaneous Item) will be inserted automatically when the technician is selected in WWS.
Scope 1:
Working time:
Reworking body seal
Includes:
Removing and installing cover
Removing and installing battery
Work instructions after disconnecting the battery
Removing and installing front luggage compartment trim
panel
Removing and installing front trim (wing flange)
Removing and installing wiper arm
Removing and installing cowl panel cover
Removing and installing wiper linkage
Removing and installing front wheel housing liner (front part)
Removing and installing headlights
Removing and installing battery console
Removing and installing engine-compartment blower
Removing and installing rear wheels
Removing and installing rear wheel housing liner
Removing and installing rear roof trim panel
Checking and reworking rubber sleeves and stoppers
Reworking seam seal
Sealing body cavities
Labor time: 555 TU
Parts required:
999.915.337.40
Sealing foam
2 ea.
999.703.196.40
Stopper in luggage compartment, side
2 ea.
999.703.421.40
Stopper on longitudinal member, top
4 ea.
000.043.303.38
Adhesive film for longitudinal member, top
1 ea.
999.703.195.40
Stopper in luggage compartment, bottom
(oval)
1 ea.
2012© Porsche Cars North America, Inc.
AfterSales
Jul 19, 2012
Page 31 of 34
5
Service
WC25
ENU
Technical Information
37/12
999.703.543.40
Stopper in luggage compartment, bottom
(round)
1 ea.
911.095.932.20.xxx
or
911.095.933.20.xxx
Touch-up stick for solid colors
or
Touch-up stick for metallic colors
2 ea.
WC250000001*
Body sealant
commercially available, e.g.
- Makra Evo-Seal 801
- Sikaflex 529
- Lord Fusor 804
- 3M MSP 8374
1 ea.*
(For warranty
invoicing only)
WC250000002*
Expendable items
(adhesive tape, paper)
1 ea. *
(For warranty
invoicing only)
* The WWS Warranty system will automatically add into the “Miscellaneous item” section (sublet) of the
claim after the claim has been submitted.
⇒ Damage code WC25 066 000 1
Scope 2:
Scope 2 must be invoiced if the work is outsourced.
Working time:
Labor time: 0 TU
Reworking body seal
The work involved will be outsourced and will therefore be invoiced according to third-party (sublet)
labor time.
Parts required:
Jul 19, 2012
Page 32 of 34
999.915.337.40
Sealing foam
2 ea.
999.703.196.40
Stopper in luggage compartment, side
2 ea.
999.703.421.40
Stopper on longitudinal member, top
4 ea.
000.043.303.38
Adhesive film for longitudinal member, top
1 ea.
999.703.195.40
Stopper in luggage compartment, bottom
(oval)
1 ea.
AfterSales
2012© Porsche Cars North America, Inc.
Service
Technical Information
37/12 ENU
WC25
999.703.543.40
Stopper in luggage compartment, bottom
(round)
1 ea.
911.095.932.20.xxx
or
911.095.933.20.xxx
Touch-up stick for solid colors
or
Touch-up stick for metallic colors
2 ea.
WC250000001*
Body sealant
commercially available, e.g.
- Makra Evo-Seal 801
- Sikaflex 529
- Lord Fusor 804
- 3M MSP 8374
1 ea.*
(For warranty
invoicing only)
WC250000002*
Expendable items
(adhesive tape, paper)
1 ea. *
(For warranty
invoicing only)
5
* The WWS Warranty system will automatically add into the “Miscellaneous item” section (sublet) of the
claim after the claim has been submitted.
Third-party labor:
Removing and installing cover
Removing and installing battery
Work instructions after disconnecting the battery
Removing and installing front luggage compartment trim panel
Removing and installing front trim (fender flange)
Removing and installing wiper arm
Removing and installing cowl panel cover
Removing and installing wiper linkage
Removing and installing front wheel housing liner (front part)
Removing and installing headlights
Removing and installing battery console
Removing and installing engine-compartment blower
Removing and installing rear wheels
Removing and installing rear wheel housing liner
Removing and installing rear roof trim panel
Checking and reworking rubber sleeves and stoppers
Reworking seam seal
Sealing body cavities
2012© Porsche Cars North America, Inc.
AfterSales
Third-party labor
time: 555 TU
Jul 19, 2012
Page 33 of 34
5
Service
WC25
ENU
Technical Information
37/12
⇒ Damage code WC25 066 000 1
References:
⇒ Workshop Manual ’852219 Removing and installing cover’
⇒ Workshop Manual ’270619 Removing and installing battery’
⇒ Workshop Manual ’700519 Removing and installing front luggage compartment trim panel’
⇒ Workshop Manual ’700219 Removing and installing front trim (wing flange)’
⇒ Workshop Manual ’922519 Removing and installing wiper arm’
⇒ Workshop Manual ’508719 Removing and installing cowl panel cover’
⇒ Workshop Manual ’921919 Removing and installing wiper linkage’
⇒ Workshop Manual ’505619 Removing and installing front wheel housing liner’
⇒ Workshop Manual ’941519 Removing and installing headlights’
⇒ Workshop Manual ’198119 Removing and installing engine-compartment blower’
⇒ Workshop Manual ’440519 Removing and installing wheel’
⇒ Workshop Manual ’536919 Removing and installing rear wheel housing liner’
⇒ Workshop Manual ’708519 Removing and installing rear roof trim panel’
⇒ Workshop Manual ’2X00IN Work instructions after disconnecting the battery’
Important Notice: Porsche Cars N.A Technical Bulletins are intended for use by professional technicians, not a "Do-it-yourselfer." They are written to inform these technicians of conditions that may
occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Special tools may be required to perform certain operations identified in these bulletins. Use of tools
and procedures other than those recommended in these bulletins may be detrimental to the safe operation of your vehicle. Properly trained technicians have the equipment, tools, safety instructions
and know-how to do a job properly and safely. If a condition is described, do not assume that the bulletin applies to your vehicle, or that your vehicle will have that condition. See your Porsche Dealer for
information on whether your vehicle may benefit from the information. Part numbers listed in these bulletins are for reference only. Always check with your authorized Porsche dealer to verify correct part
numbers.
© Porsche Cars North America, Inc.
Dealership
Distribution
Routing
Service Manager
_______
Shop Foreman
_______
Service Technician
________
_______
_______
_______
Asst. Manager
_______
Warranty Admin.
_______
Service Technician
________
_______
_______
_______
Dr. Ing. h.c. F. Porsche AG is the owner of numerous trademarks, both registered and unregistered, including without limitation the Porsche Crest®, Porsche®, Boxster®, Carrera®, Cayenne®,
Cayman™, Panamera®, Tiptronic®, VarioCam®, PCM®, 911®, 4S®, FOUR, UNCOMPROMISED.® and the model numbers and distinctive shapes of Porsche’s automobiles such as, the federally
registered 911 and Boxster automobiles. The third party trademarks contained herein are the properties of their respective owners. Some vehicles may be shown with non-U.S. equipment. Porsche
recommends seat belt usage and observance of traffic laws at all times.
Printed in the USA
Jul 19, 2012
Page 34 of 34
AfterSales
2012© Porsche Cars North America, Inc.
- 💯【Conta.ct us for Support Directly】If you met any...
- 🔥🔥🔥【2026 AUTEL FLAGSHIP MK900BT MK900-BT, NEW...
- 🚗【3000+ ACTIVE TESTS (50➡3000+), SAME AS MS...
- 🚗【40+ HOT SERVICES FOR 150 MAKES (28+➡40+)】Full...
- 🚗【OE ALL SYSTEM DIAGNOSE, AUTO SCAN 2.0: SCAN LICENSE...
- 📌【We are Here for You】Dear valued customer, please be...
- 🚀【5X Faster Next-Level Hardware, Same as MK900/ MX...
- 🔥【3000+ Active Tests = MK900/MK900BT but...
- 📢【2026 U.S. Version, All-in-One as MK808S/ MK808Z...
- 🔥【28+ Hot Services for 150+ Brands】Same as MaxiCOM...
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: 122-Y5V9G-06
Replacement Service Bulletin Number:
MFR Communication Date: 2012-08-06
MFR Internal Campaign ID/Software Version:
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: STRUCTURE:BODY:TRUNK LID
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- [Notice] When you receive a used device, it may be a customer return resold by Amazon without inspection. You can exchange it for a new one through Amazon. As this situation is unavoidable, we sincerely apologize. For any issues, contacting us via Amazon's "Messages" is the best way. THINKSCAN 689BT Bidirectional Scan Tool Can Be Used Immediately After It is Turned On, Without Complicated Registration Process, Which is More Convenient & Quick.
- Full Bi-Directional Control & 3000+ Active Tests: Take control and test components like actuators, fuel injectors, relays, and cooling fans in real time. You’ll quickly see if the problem is in the part itself or the control module — saving you hours of guesswork and frustrating trial-and-error.
- Advanced ECU Coding Capabilities: Handle module matching and hidden feature activation with confidence. When you replace an ECU or want to customize settings, this obd2 scanner diagnostic bi directional tool gives you the professional-level capabilities you need without the dealership price tag.
- 34+ Useful Reset and Maintenance Functions: Complete everyday service tasks smoothly with a wide range of helpful reset and maintenance functions. Whether you’re keeping up with regular upkeep or tackling a specific job, this scanner makes maintenance simpler and less stressful for both DIYers and pros.
- Comprehensive Full System Diagnostics: Diagnose every major system — Engine, Transmission, ABS, SRS, TPMS, and more — all in one place. Finally stop wondering if you’re missing something important; get the full picture and clear codes with ease.
- Top Reasons to Choose the D7S OBD2 Scanner: XTOOL D7S car scan tool, an upgrade of XTOOL D7, offers comprehensive features for automotive technicians, workshops, and DIY enthusiasts 1. Upgraded Hardware: 2+64GB memory, rear camera, intuitive interface, foldable bracket 2. Complete Diagnostics: FCA
Autoauth, OE-level all system scan, 39+ maintenance services, 4K+ bidirectional, CANFD/DoIP protocol 3. Advanced Capabilities: ECU coding, PMI functions 4. Wide Compatibility: Support 10,000+ models, covering 99% vehicle brands 5. Multi-language: Available in 22+ languages, No IP Restrictions 6. 3-Year Updates: Save 300 bucks on software updates for the latest features and optimizations - 2026 Upgraded D7S Car Scanner Features: The newly 2026 D7S V2.0 scanner for car brings exciting features for advanced vehicle diagnostics and enhanced user experience 1. FCA AutoAuth: Now supports FCA SGW module for Chrysler, for Jeep, for Dodge (2018+), for Fiat (2017+), enabling faster vehicle communication without gateway restrictions 2. PMI (Offline ECU Programming): Allows for Ford, for Lincoln, and for Mazda ECU programming for new modules 3. Optimized Diagnostic Report 2.0: Personalized reports with logos and customer info for auto shops. Note: Compatibility varies by cars, please check before order
- Cost-effective ECU Coding Scan Tool for Specific Brands: Enhance your vehicle's performance with XTOOL D7S! This obd2 scanner all systems bidirectional offers advanced capabilities at an affordable price, supports online for BMW, for Benz and offline for BENZ, for MIT, along with PMI functions for Ford, for Mazda, and for Lincoln. Ideal for technicians and DIY enthusiasts, this automotive scanner diagnostic tool optimizes vehicle performance and enhances the driving experience. Note: Not for all cars and modules, please send car VIN to check the compatibility before purchase
- OE All System Diagnostic & 8 Pids Graphing: XTOOL D7S is a comprehensive all system bi directional obd2 scanner that delivers dealer-level diagnostics, completely controlling over your vehicle’s performance and health. This automotive scan tool can read and clear DTCs, view live data and ECU information, retrieve freeze frames, and perform active tests and full obd2 functions. This bi-directional scan tool can can identify your vehicle's make, model, and year information with just one click and show up to 8 PIDs live data with options for CSV viewing, playback, and recording for in-depth analysis. It is easy-to-use for both professionals and beginners, helping pinpoint issues efficiently
- 3 Years Software Update, Value for Money: With 3 years of software updates and 22+ languages(no IP restrictions), XTOOL D7S auto scanner code scanner ensures ongoing compatibility for the latest car models and improved diagnostic functions. This all system vehicle diagnostic scanner comes with a 30-day return policy and a 24-month repair for dependable performance. XTOOL are dedicated to your satisfaction, so enjoy seamless support and lifetime expert assistance. Should you encounter any issues or concerns, don’t hesitate to reach out XTOOL. D7S with newest update with 22 languages freely transfer without authorization, check details from setting-language or from XTOOL
- 【✅Compared to BOSSCOMM IF742, IF745 Offers Full-System Diagnostics】The BOSSCOMM IF745 car diagnostic scanner is an upgraded model of IF742. In addition to supporting all OBD2 Code Reader functions and 6 reset options (ABS/EPB/SAS/BMS/Oil/Throttle), it expands diagnostics from 4 systems (Check Engine/ABS/SRS/Transmission) to vehicle All systems, including Steering, Suspension, and Body Electronics. This provides deeper, more comprehensive diagnostic capabilities.
- 【✨10 OBD2 Functions】The BOSSCOMM IF745 scan tool’s DTC Lookup instantly translates fault codes into user-friendly explanations, its I/M Readiness feature streamlines emissions testing with a single tap, and Freeze Frame lets you pinpoint the exact moment of a fault for in-depth root-cause diagnosis. Combined with a live data dashboard and advanced diagnostics (O2S, OBMon, EVAP), it delivers comprehensive insights for confident troubleshooting.
- 【✨Deep Diagnostics for All Vehicle System Modules】Beyond code reading/clearing and ECU information retrieval, our all-in-one data stream feature lets you inspect all current fault codes and their locations across the vehicle’s systems. This vehicle code reader helps you turn off dashboard warning lights and perform a comprehensive self-check of your car at home—no more back-and-forth trips to the repair shop or hefty inspection fees.
- 【✨6 Essential Resets: ABS Bleeding, Oil, EPB, SAS, Throttle, BMS】The BOSSCOMM IF745 obd2 scanner diagnostic tool swiftly purges air from brake lines to restore braking sensitivity, fine-tunes maintenance cycles to eliminate false alerts, resolves parking brake issues with one-click control, recalibrates steering sensors for stability, optimizes engine idling/acceleration for smoother performance, and deeply resets battery systems to extend lifespan and range via precise parameter adjustments.❗NOTE: Does NOT support bidirectional control, coding, or programming.
- 【✨10,000+ Car Models, AutoVIN, 13 Languages】The BOSSCOMM IF745 vehicle scanner diagnostic tool covers 73+ global car brands and offers support in 13 languages, making it perfect for DIYers, auto mechanics, or as a thoughtful gift. With a single-click AutoVIN feature, it instantly retrieves vehicle serial numbers, streamlining diagnostics for users globally. This adaptable tool balances user-friendliness with precision, catering to both personal and professional requirements.✅Unsure about compatibility? Compatibility will vary on vehicles' model and year, pls reach us via 📧 [email protected] 📧 before purchase.
This product presentation was made with AAWP plugin.