Classification:

Reference:

Date:

EC13-015e

ITB13-044e

March 30, 2017

ALL MODEL YEAR 2012 AND NEWER INFINITI VEHICLES;
EVAP LEAK DTC P0442, P0455, P0456 INFORMATION
This bulletin has been amended. The bulletin now includes vehicles in production as of the date of this update.
No other changes have been made. Please discard all previous versions of this bulletin.

APPLIED VEHICLES:

All model year 2012 and newer Infiniti vehicles

SERVICE INFORMATION

Example

All model year 2012 and newer Infiniti vehicles have a warning indicator in
the instrument area to alert the driver of a loose fuel filler cap (see Figure 1
example).
Figure 1


If a vehicle displays a Loose Fuel Filler Cap warning light or message, the driver should safely stop the
vehicle and make sure the fuel filler cap is installed correctly.



Make sure the customer is informed of the proper fuel filler cap installation.



Customers should refer to their vehicle’s Owner’s Manual for specific details on the “LOOSE FUEL
CAP” warning system and fuel filler cap installation.

If a fuel filler cap is left loose for multiple trips, DTCs will be stored and the MIL will illuminate.


If one or more of these EVAP leak DTCs are stored (P0442, P0455, P0456), a loose fuel filler cap
may be the cause.



If P0442, P0455, and/or P0456 is found stored, begin vehicle EVAP system diagnosis using the
FLOW CHART on the next page.
 A test drive is not part of the DTC confirmation or diagnostic procedures for these DTCs.
 Test driving the vehicle for these DTCs will only waste time.
 The diagnostic procedure in this bulletin must be used for these DTCs for an effective repair.
NOTE: Any parts replaced under warranty for repair of these DTCs are on automatic parts return to
NNA for inspection. Any part found to be functional will cause a charge-back to the dealer.

Infiniti Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained
individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that
a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Infiniti retailer to determine if this
applies to your vehicle.

1/3

FLOW CHART
Connect CONSULT-III plus
(C-III plus) to the vehicle

Were any of the following DTCs found
stored:
No
• P0442
• P0455
• P0456

This bulletin
does not apply

Yes
NOTE: A “smoke” leak detection
machine may be used. Follow
the manufacturer’s operating
instructions.

1. Confirm fuel filler cap is secure
2. Connect Essential Tool
J-42909 to EVAP service port
3. Using Active Test, close vent
control valve
4. Apply pressure using
J-42909 until bar graph reaches
about halfway
5. Monitor the bar graph for
10 minutes

Did bar graph remain stable?

•

NO EVAP LEAK detected
at this time

•

MIL ON due to fuel filler
cap not being properly
secured (loose)

•

Erase DTC(s)

•

Advise customer fuel filler
cap ALWAYS needs to be
properly secured

•

DO NOT REPLACE FUEL
FILLER CAP OR ANY
OTHER EVAP RELATED
PARTS

•

See CLAIMS INFORMATION
on page 3

Yes

No

EVAP leak detected
This bulletin does not apply
Refer to ASIST and the vehicle
related Service Manual for further
diagnosis

2/3

ITB13-044e

EVAP System Operation


Fuel vapor flows from fuel tank into canister (light blue area)



Vapor flows from canister through purge control valve (red line)



Fresh air flows into canister (green line)

Figure 2

CLAIMS INFORMATION
Submit a Primary Part (PP) type line claim using the following claims coding:
DESCRIPTION
PFP
OP CODE
SYM
EVAP System Leak Test

(1)

FX47AA

ZE

DIA

FRT

32

0.4

(1) Refer to the electronic parts catalog (FAST or equivalent) and use the Fuel Cap part number (17251-xxxxx)
as the primary failed part.

3/3

ITB13-044e