NHTSA ID Number: 10108259
Manufacturer Communication Number: A10-039
TSB/Document Date: 2017-06-30
Summary
THE INSPECTION PROCEDURE FOR TAKATA DRIVERS AIRBAGS WAS REMOVED BECAUSE ALL TAKATA DRIVERS AIRBAG INFLATORS INSTALLED IN THE RECALL VEHICLE POPULATION ARE BEING REPLACED. FOR CIVIC MODELS ONLY, AUTOLIV AIRBAGS ARE OK AND CAN BE REINSTALLED IN THE VEHICLE. A MANUFACTURING ERROR CAN PRODUCE OVER-PRESSURIZATION OF SOME REPLACEMENT DRIVERS (FRONT) AIRBAG INFLATORS DURING AIRBAG DEPLOYMENT. IF AN AFFECTED AIRBAG DEPLOYS, THE INCREASED INTERNAL PRESSURE MAY CAUSE THE INFLATOR CASING TO RUPTURE. METAL FRAGMENTS COULD PASS THROUGH THE AIRBAG CUSHION MATERIAL, POSSIBLY CAUSING AN INJURY OR FATALITY TO VEHICLE OCCUPANTS.
Do not reuse.
~~------1.,...~~
~
INFLATOR
I
~
~:~~.~"'"'· ~~ ~
AIRBAG
8.
Use shop air to clean any debris that may be on the inflator, then remove the inflator from the airbag.
NOTE:
Do not allow any debris to enter the inflator opening in the airbag.
•
•
Do not deploy the inflator. The inflator must be returned to its supplier in the box the new inflator came in.
9.
Turn over the airbag (inflator side down), and shake it to remove any debris from the inflator opening.
Page 6 of 16
10. Install the new inflator in the airbag.
NOTE: There may be some minor surface rust or corrosion on the new inflator; this is OK.
Click on the image below for a short video about the different variations of the driver's and front passenger's
replacement inflators involved with the recalls related to Takata inflators. While both the driver's and front
passengers inflators are shown in the video, this is informational only. Replace inflators only as directed by the iN
VIN status inquiry.
Check your part number against the ones listed for each installation procedure. Use the correct installation
procedure for the part you received.
Part Number
04 770-SSA-305
Refer to Driver's lnflator Type 1 in the video.
I
The inflator is one piece and
fits easily into the airbag assembly.
•
Insert the inflator into the opening.
NOTE: Make sure the inflator wires are positioned toward the bottom of the airbag. If you install the inflator
incorrectly, you may not be able to reconnect the SRS airbag harness.
Page 7 of 16
Check your part number against the ones listed for each installation procedure. Use the correct installation
procedure for the part you received.
Part Number
04 770-SSA-405
Refer to Driver's lnflator Type 2 in the video
The inflater is one piece.
A wide flange is halfway up
the body of the inflater.
•
Insert the airbag inflator into the opening. Do not force it into the airbag module.
NOTE: Make sure the inflator wires are positioned toward the bottom of the airbag. If you install the inflator
incorrectly, you may not be able to reconnect the SRS airbag harness .
.----------------
Page 8 of 16
•
Using a pair of pliers, gently pull up on each stud up while pushing the inflator module down until the airbag is
properly seated within the airbag module.
PROPERLY
SEATED
11. Install and torque the new locknuts to 3.9 N·m (2.8 lb-ft, 34 lb-in).
12. Cover the lower two inflator locknuts with new felt tape.
13. Reinstall the horn plate with new felt washers on its mounting bolts. Torque the mounting bolts to 3.4 N ·m (2.5 lb-ft,
30 lb-in), then make sure the horn plate moves freely.
14. Reinstall the driver's airbag using new Torx bolts and torque the bolts to 9.8 N ·m (7 .2 lb-ft).
15. Give your warranty clerk the R.O. that includes the inflator serial number and replacement part number. For the
warranty claim to be paid, the replacement inflator part number must be on the warranty claim and your warranty
clerk must enter the serial number in the Diagnostic Trouble Codes field.
Page 9 of 16
REPAIR PROCEDURE B - CIVIC, CIVIC HYBRID
, CR-V, AND ODYSSEY
NOTE:
Be careful not to damage any parts when replacing the inflator, and follow the procedure exactly.
•
If, before removing the airbag, you suspect that it may not be the correct airbag for the vehicle or a counterfeit,
•
do not remove the airbag. Contact your DPSM for assistance.
Do not open the inflator kit until you have confirmed a Takata inflator is installed in the vehicle because if you
•
have to return the inflator, the kit must be unopened.
•
If the Civic you are inspecting has an Autoliv airbag and inflator, do not disassemble the airbag because the
inflator cannot be reinstalled, and you will have to replace the airbag module.
1.
Remove the driver's airbag.
2.
Peel the label located inside the inflator box from its backing and attach it to the R.O. For the warranty claim to be
paid, the replacement inflator part number that you received must be on the warranty claim and your warranty
clerk must enter the serial number in the Diagnostic Trouble Codes field.
NOTE:
• The replacement part number is printed on the top part of the label and the serial number is printed on the
bottom. Make sure you attach the label to the R.O. and give it to the warranty clerk.
• There may also be a colored sticker located in the kit, ignore it because it is not used.
•
Not all inflator kits have a label included. In those cases, write the serial number and part number from the side
of the inflator box on the R.O. The part number always starts with 047.
INFLATOR PARTS BOX
PART NUMBER
L
--&4...
78"!""'
6- SilX-~30~6- - - - - - . . . _
1mi 1rn mn11 ~ ~ 1111111,111 11
2477186e07 4610
--7
SERIAL NUMBER
RETAINER
PLATE
SELF-ADHESIVE
LABEL
3.
INFLATOR
INSTALLATION
PARTS
(if applicable)
Place the airbag, face down, on a clean shop towel.
Page 10 of 16
4.
Visually inspect the airbag and the inflator for any unusual writing or markings.
•
•
If there is nothing unusual about the airbag or the inflator, go to step 5.
If there is unusual markings, like an incorrect label or a model year written in marker, the airbag and inflator may
not be the correct airbag and/or inflator for the vehicle or it may be a counterfeit part. For more information
about counterfeit airbags, you can refer to safercar.gov, enter keywords MANAGING COUNTERFEIT, and
select Recommended Dealer Guidance for Managing Counterfeit Air Bags from the list. If you suspect that the
airbag or inflator is counterfeit, do not continue this procedure. Contact your DPSM for assistance.
NON-STANDARD SAFETY LABEL
5.
NON-STANDARD WIRES
Civic only - Determine if the airbag is made by Autoliv or Takata by comparing the inflators to those in the images
below.
NOTE: The Autoliv serial number label is different from the Takata label; the Autoliv has 11 characters, the Takata
has 9.
TAKATA
•
•
If the airbag is made by Autoliv, the airbag is OK. Reinstall the Autoliv airbag. If you already received a
replacement inflator, return the unopened kit to American Honda.
If the airbag is made by Takata, go to step 6.
Page 11 of 16
6.
Using needle-nose vise grips or a 3/8 in. 6-point socket, remove the four locknuts from the inflator. The locknuts will
not be reused.
NOTE: Do not remove the inflator from the airbag until you complete step 7.
LOCKNUTS (4)
Do not reuse.
.@-.
-~-----1.,..~~
~
7.
Use shop air to clean any debris that may be on the inflator, then remove the inflator from the airbag.
NOTE:
Do not allow any foreign objects to enter the inflator opening in the airbag.
•
•
Do not deploy the inflator. The inflator must be returned to its supplier in the box the new inflator came in.
8.
Turn over the airbag (inflator side down), and shake it to remove any debris from the inflator opening.
Page 12 of 16
9.
Install the new inflator in the airbag.
NOTE: There may be some minor surface rust or corrosion on the new inflator; this is OK.
Click on the image below for a short video about the different inflators.
Check your part number against the ones listed for each installation procedure. Use the correct installation
procedure for the part you received.
Part Number
04 770-SSA-305
04 770-S9A-306
•
Insert the inflator into the opening.
NOTE: Make sure the inflator wires are positioned toward the bottom of the airbag. If you install the inflator
incorrectly, you may not be able to reconnect the SRS airbag harness.
Page 13 of 16
Check your part number against the ones listed for each installation procedure. Use the correct installation
procedure for the part you received.
Part Number
04 770-SSA-405
04 770-S9A-405
•
Insert the airbag inflator into the opening. Do not force it into the airbag module.
NOTE: Make sure the inflator wires are positioned toward the bottom of the airbag. If you install the inflator
incorrectly, you may not be able to reconnect the SRS airbag harness.
•
Using a pair of pliers, gently pull up on each stud up while pushing the inflator module down until the airbag is
properly seated within the airbag module.
PROPERLY
SEATED
Page 14 of 16
Check your part number against the ones listed for each installation procedure. Use the correct installation
procedure for the part you received.
Part Number
04 770-SSA-408
Refer to Driver's lnflator Type 3 in the video.
The inflator is held down
by a directional retainer
that is keyed to the inflator.
~~
•
Place the inflator into the opening with the inflator harness toward the bottom of the airbag.
The inflator fits
easily into the
airbag assembly.
•
Install the bracket onto the studs. Make sure the locator tab fits into the locator hole as shown.
NOTE: Make sure the harness comes out through the center opening. Do not install the bracket over the
harness wires.
Page 15 of 16
Check your part number against the ones listed for each installation procedure. Use the correct installation
procedure for the part you received.
Part Number
04 770-S9A-409
Refer to Driver's lnflator Type 4 in the video.
The inflator is held down
by a directional retainer
that is keyed to the inflator.
•
Place the inflator into the opening with the inflator harness toward the bottom of the airbag.
Line up these three tabs
with the notches in the inflator.
•
Install the bracket onto the studs with the stamp LOWER at the bottom of the airbag.
•
Make sure the three tabs and notches are properly aligned.
NOTE:
•
The tabs and notches are designed to align in one direction only. If the tabs and notches are not aligned,
the inflator and bracket are not installed correctly.
•
Make sure the harness comes out through the center opening. Do not install the bracket over the harness
wires.
10. Install and torque the new locknuts to 3.9 N·m (2.8 lb-ft, 34 lb-in).
11. Reinstall the driver's airbag using new Torx bolts and torque the bolts to 9.8 N·m (7.2 lb-ft).
12. Give your warranty clerk the R.O. that includes the inflator serial number and replacement part number. For the
warranty claim to be paid, the replacement inflator part number must be on the warranty claim and your warranty
clerk must enter the serial number in the Diagnostic Trouble Codes field.
END
Page 16 of 16
- 💯【Conta.ct us for Support Directly】If you met any...
- 🔥🔥🔥【2026 AUTEL FLAGSHIP MK900BT MK900-BT, NEW...
- 🚗【3000+ ACTIVE TESTS (50➡3000+), SAME AS MS...
- 🚗【40+ HOT SERVICES FOR 150 MAKES (28+➡40+)】Full...
- 🚗【OE ALL SYSTEM DIAGNOSE, AUTO SCAN 2.0: SCAN LICENSE...
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: A10-039
Replacement Service Bulletin Number:
MFR Communication Date: 2015-05-21
MFR Internal Campaign ID/Software Version:
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: AIR BAGS
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- [Notice] When you receive a used device, it may be a customer return resold by Amazon without inspection. You can exchange it for a new one through Amazon. As this situation is unavoidable, we sincerely apologize. For any issues, contacting us via Amazon's "Messages" is the best way. THINKSCAN 689BT Bidirectional Scan Tool Can Be Used Immediately After It is Turned On, Without Complicated Registration Process, Which is More Convenient & Quick.
- Full Bi-Directional Control & 3000+ Active Tests: Take control and test components like actuators, fuel injectors, relays, and cooling fans in real time. You’ll quickly see if the problem is in the part itself or the control module — saving you hours of guesswork and frustrating trial-and-error.
- Advanced ECU Coding Capabilities: Handle module matching and hidden feature activation with confidence. When you replace an ECU or want to customize settings, this obd2 scanner diagnostic bi directional tool gives you the professional-level capabilities you need without the dealership price tag.
- 34+ Useful Reset and Maintenance Functions: Complete everyday service tasks smoothly with a wide range of helpful reset and maintenance functions. Whether you’re keeping up with regular upkeep or tackling a specific job, this scanner makes maintenance simpler and less stressful for both DIYers and pros.
- Comprehensive Full System Diagnostics: Diagnose every major system — Engine, Transmission, ABS, SRS, TPMS, and more — all in one place. Finally stop wondering if you’re missing something important; get the full picture and clear codes with ease.
- Top Reasons to Choose the D7S OBD2 Scanner: XTOOL D7S car scan tool, an upgrade of XTOOL D7, offers comprehensive features for automotive technicians, workshops, and DIY enthusiasts 1. Upgraded Hardware: 2+64GB memory, rear camera, intuitive interface, foldable bracket 2. Complete Diagnostics: FCA
Autoauth, OE-level all system scan, 39+ maintenance services, 4K+ bidirectional, CANFD/DoIP protocol 3. Advanced Capabilities: ECU c0ding, PMI functions 4. Wide Compatibility: Support 10,000+ models, covering 99% vehicle brands 5. Multi-language: Available in 22+ languages, No IP Restrictions 6. 3-Year Updates: Save 300 bucks on software updates for the latest features and optimizations - 2026 Upgraded D7S Car Scanner Features: The newly 2026 D7S V2.0 scanner for car brings exciting features for advanced vehicle diagnostics and enhanced user experience 1. FCA AutoAuth: Now supports FCA SGW module for Chrysler, for Jeep, for Dodge (2018+), for Fiat (2017+), enabling faster vehicle communication without gateway restrictions 2. PMI (Offline ECU Pr0gramming): Allows for Ford, for Lincoln, and for Mazda ECU pr0gramming for new modules 3. Optimized Diagnostic Report 2.0: Personalized reports with logos and customer info for auto shops. Note: Compatibility varies by cars, please check before order
- 39+ Services/Resets/Adaptations/Relearns/Calibrations: XTOOL D7S full system car scanner diagnostic tool tackles 99% of common car issues through its 36+ special functions, including Oil Reset, EPB, SAS, BMS, Throttle Reset, Injector C0ding, ABS Bleed, TPMS Reset, Power Balance, etc and also covers specific-vehicle functions like Crank Sensor Relearn, ABS Initialization, Cylinder Power Balance, Fuel Trim Reset, Idle Relearn etc. This car diagnostic scanner enhances efficiency, making repairs and maintenance hassle-free. Tip: DO NOT for All vehicles, please check compatibility first
- Cost-effective ECU C0ding Scan Tool for Specific Brands: Enhance your vehicle's performance with XTOOL D7S! This obd2 scanner all systems bidirectional offers advanced capabilities at an affordable price, supports online for BMW, for Benz and offline for BENZ, for MIT, along with PMI functions for Ford, for Mazda, and for Lincoln. Ideal for technicians and DIY enthusiasts, this automotive scanner diagnostic tool optimizes vehicle performance and enhances the driving experience. Note: Not for all cars and modules, please send car VIN to check the compatibility before purchase
- OE All System Diagnostic & 8 Pids Graphing: XTOOL D7S is a comprehensive all system bi directional obd2 scanner that delivers dealer-level diagnostics, completely controlling over your vehicle’s performance and health. This automotive scan tool can read and clear DTCs, view live data and ECU information, retrieve freeze frames, and perform active tests and full obd2 functions. This bi-directional scan tool can can identify your vehicle's make, model, and year information with just one click and show up to 8 PIDs live data with options for CSV viewing, playback, and recording for in-depth analysis. It is easy-to-use for both professionals and beginners, helping pinpoint issues efficiently
- 【✅Compared to BOSSCOMM IF742, IF745 Offers Full-System Diagnostics】The BOSSCOMM IF745 car diagnostic scanner is an upgraded model of IF742. In addition to supporting all OBD2 Code Reader functions and 6 reset options (ABS/EPB/SAS/BMS/Oil/Throttle), it expands diagnostics from 4 systems (Check Engine/ABS/SRS/Transmission) to vehicle All systems, including Steering, Suspension, and Body Electronics. This provides deeper, more comprehensive diagnostic capabilities.
- 【✨10 OBD2 Functions】The BOSSCOMM IF745 scan tool’s DTC Lookup instantly translates fault codes into user-friendly explanations, its I/M Readiness feature streamlines emissions testing with a single tap, and Freeze Frame lets you pinpoint the exact moment of a fault for in-depth root-cause diagnosis. Combined with a live data dashboard and advanced diagnostics (O2S, OBMon, EVAP), it delivers comprehensive insights for confident troubleshooting.
- 【✨Deep Diagnostics for All Vehicle System Modules】Beyond code reading/clearing and ECU information retrieval, our all-in-one data stream feature lets you inspect all current fault codes and their locations across the vehicle’s systems. This vehicle code reader helps you turn off dashboard warning lights and perform a comprehensive self-check of your car at home—no more back-and-forth trips to the repair shop or hefty inspection fees.
- 【✨6 Essential Resets: ABS Bleeding, Oil, EPB, SAS, Throttle, BMS】The BOSSCOMM IF745 obd2 scanner diagnostic tool swiftly purges air from brake lines to restore braking sensitivity, fine-tunes maintenance cycles to eliminate false alerts, resolves parking brake issues with one-click control, recalibrates steering sensors for stability, optimizes engine idling/acceleration for smoother performance, and deeply resets battery systems to extend lifespan and range via precise parameter adjustments.❗NOTE: Does NOT support bidirectional control, coding, or programming.
- 【✨10,000+ Car Models, AutoVIN, 13 Languages】The BOSSCOMM IF745 vehicle scanner diagnostic tool covers 73+ global car brands and offers support in 13 languages, making it perfect for DIYers, auto mechanics, or as a thoughtful gift. With a single-click AutoVIN feature, it instantly retrieves vehicle serial numbers, streamlining diagnostics for users globally. This adaptable tool balances user-friendliness with precision, catering to both personal and professional requirements.✅Unsure about compatibility? Compatibility will vary on vehicles' model and year, pls reach us via 📧 [email protected] 📧 before purchase.
This product presentation was made with AAWP plugin.