4/27/2016 LTB00799NAS2- Engine MIL Illuminated With No Hardware Fault and DTCs P0044, P013A, P0300, P0301, P0302, P0303, P0304, P0420, P050B, P1315, ...

TECHNICAL BULLETIN
LTB00799NAS2
27 APR 2016
© Jaguar Land Rover North America, LLC
NOTE: The information in Technical Bulletins is intended for use by trained, professional Technicians with the knowledge,
tools, and equipment required to do the job properly and safely. It informs these Technicians of conditions that may occur on
some vehicles, or provides information that could assist in proper vehicle service. The procedures should not be performed by
'do-it-yourselfers'. If you are not a Retailer, do not assume that a condition described affects your vehicle. Contact an
authorized Land Rover service facility to determine whether this bulletin applies to a specific vehicle.

This reissue replaces all previous versions. Please destroy all previous versions.
Changes are highlighted in gray

SECTION: 303-00

Engine MIL Illuminated With No Hardware Fault and DTCs P0044, P013A,
P0300, P0301, P0302, P0303, P0304, P0420, P0S0B, P1315, and/orP2188
Stored
AFFECTED VEHICLE RANGE:
Range Rover Evoque (LV)
Model Year:
2014-2015

VIN:
Assembly
Plant:

856580-065800

Engine:

GTDi 2.0L Petrol
GTDi 2.0L Petrol - SULEV

Halewood

MARKETS:
NAS

CONDITION SUMMARY:
Situation: The engine Malfunction Indicator Lamp (MIL) may be illuminated. Upon diagnosis, the technician may
find no hardware fault and one or more of the following Diagnostic Trouble Codes (DTC) stored in the Powertrain
Control Module (PCM): P0044, P013A, P0300, P0301, P0302, P0303, P0304, P0420, P050B, P1315, and/or
P2188. Information relating to the third byte of the DTC is not required to qualify code against this bulletin.
Cause: This may be caused by an On-board Diagnostics (OBD) calibration error.
Action: Should a customer express this concern, follow the Service Instruction below.

PARTS:
No Parts Required

TOOLS:
-~
NOTE: This 'Active Bulletin' that will display a functional programming shortcut if accessed within
a diagnostic session.
Jaguar Land Rover-approved diagnostic tool with latest DVD and Calibration File
Jaguar Land Rover-approved Midtronics battery power supply

WARRANTY:
~
NOTE: Use DDW to check for any Recall, Service Action, or Update Prior to Sale notice requiring a
Powertrain Control Module (PCM) software update. If 'yes', perform and claim the PCM update as per
that program.
6 , NOTE: Repair procedures are under constant review, and therefore times are subject to change;
those quoted here must be taken as guidance only. Always refer to TOPix to obtain the latest repair
http://topix.landrover.jlrext.com/topix/content/document/view?id=646035

1/3

4/27/2016 LTB00799NAS2- Engine MIL Illuminated With No Hardware Fault and DTCs P0044, P013A, P0300, P0301, P0302, P0303, P0304, P0420, P050B, P1315, ...

time.
6 , NOTE: DDW requires the use of causal part numbers. Labor only claims must show the causal part
number with a auantitv of zero.
DESCRIPTION

SRO

TIME
(HOURS)

CONDITION
CODE

CAUSAL
PART

Configure existing module - Powertrain Control
Module

12.90.13

0.2

04

LRO28981

Powertrain control module adaption clear

18.90.27

0.2

04

LRO28981

6 , NOTE: Normal Warranty procedures apply.

SERVICE INSTRUCTION:
& ..C AUTION: A Jaguar Land Rover-approved Midtronics battery power supply must be connected to the
vehicle battery during SDD diagnosis/ module programming.
& ..C AUTION: Ensure all ignition 'ON' / ignition 'OFF' requests are carried out; failure to perform these
steps may cause damage to control modules in the vehicle.
~
NOTE: The Jaguar Land Rover-approved diagnostic tool must be loaded with DVD142.03 v.212 or
later.

1. ~

NOTE: Check all hardware as per DTC index (see TOPix Workshop Manual, section 100-00:
General Information - Diagnostic Trouble Code (DTC)) prior to software update.

Connect the Jaguar Land Rover-approved Midtronics battery power supply to the vehicle battery.

·~
NOTE: Use DDW to check for any Recall, Service Action, or Update Prior to Sale notice requiring a
Powertrain Control Module (PCM) software update. If 'yes', perform and claim the PCM update as per that
program.

2. Turn ignition 'ON' (engine not running).
3. Connect the Jaguar Land Rover-approved diagnostic tool to the vehicle and begin a new session.
4. Follow the on-screen prompts, allowing the diagnostic tool to read the VIN, identify the vehicle, and initiating
the data collect sequence.
5. Select 'Diagnosis' from the Session Type screen.
6. Select the 'Selected Symptoms' tab, and then select one of the following:
• Powertrain > Automatic transmission and transaxle > Automatic transmission and transaxle
symptoms > Gear selector malfunction > Gear position display flashing
• Powertrain > Engine system > Engine performance > Engine cuts out
• Powertrain > Engine system > Engine performance > Noises
• Electrical > Instruments> Warning lamps> Engine malfunction lamp> Lamp illuminated (and
any of the following DTCs: P0300, P0301, P0302, P0303, P0304)
7. Select 'continue'.
8. Select the 'Recommendations' tab, and then select 'Run' to perform the 'Configure existing module Powertrain control module' option.

9. Follow all on-screen instructions to complete this task.

·~
NOTE: Once the Powertrain Control Module (PCM) has been configured, the adaption values must be
cleared as follows.
10. Select the 'Selected Symptoms' tab, and then select one of the following:
• Powertrain

> Automatic transmission and transaxle > Automatic transmission and transaxle

http://topix.landrover.jlrext.com/topix/content/document/view?id=646035

2/3

4/27/2016

LTB00799NAS2- Engine MIL Illuminated With No Hardware Fault and DTCs P0044, P013A, P0300, P0301, P0302, P0303, P0304, P0420, P050B, P1315, ...

symptoms > Gear selector malfunction > Gear position display flashing
• Powertrain > Engine system > Engine performance > Engine cuts out
• Powertrain > Engine system > Engine performance > Noises
• Electrical > Instruments> Warning lamps> Engine malfunction lamp> Lamp illuminated (and
any of the following DTCs: P0300, P0301, P0302, P0303, P0304)
11. Select 'continue'.
12. Select the 'Recommendations' tab, and then select 'Run' to perform the 'Powertrain - Powertrain control
module adaption clear' option.
13. Follow all on-screen instructions to complete this task, ensuring all Diagnostic Trouble Codes (DTC) are
cleared.
14. When all tasks are complete, select the 'Session' tab and then select the 'Close Session' option.
15. Disconnect the diagnostic tool and battery power supply from the vehicle.

http://topix.landrover.jlrext.com/topix/content/document/view?id=646035

3/3