NHTSA ID Number: 10099785
Manufacturer Communication Number: 01-006-15-3039
TSB/Document Date: 2017-05-19
Summary
SOME VEHICLES MAY EXPERIENCE MIL ILLUMINATION WITH DTC P219A:00 AND/OR P219B:00 STORED IN PCM MEMORY. THE DTCS MAY BE CAUSED BY ABNORMAL ELECTRICAL NOISE WITHIN THE ENGINE HARNESS OF CERTAIN VEHICLES. TO ELIMINATE THIS CONCERN, SEPARATE THE A/F SENSOR SIGNAL LINES FROM THE EMISSION HARNESS BY INSTALLING THE SHORT CORD SERVICE PART DETAILED IN THIS BULLETIN.
Service Bulletin
Mazda
North American Operations
Irvine, CA 92618-2922
© 2015 Mazda Motor of America, Inc.
Subject:
Bulletin No:
01-006/15
Last Issued:
04/24/2015
MIL ILLUMINATION WITH DTCs P219A:00 AND/OR P219B:00
2011-2013 CX-9 - MIL ILLUMINATION WITH DTCs P219A:00 AND/OR P219B:00
BULLETIN NOTE
• This bulletin supersedes the previous bulletin 01-027/13, issued on 10/31/13 and 11/12/13. The APPLICABLE MODEL(S)/VINS has been revised.
• Changes are noted below in Red beside the change bar.
APPLICABLE MODEL(S)/VINS
2011-2015 CX-9
DESCRIPTION
Some vehicles may experience MIL illumination with DTC P219A:00 and/or P219B:00 stored in PCM memory.
DTC
Description
P219A:00
Bank 1 Air-Fuel Ratio Imbalance
P219B:00
Bank 2 Air-Fuel Ratio Imbalance
The DTCs may be caused by abnormal electrical noise within the engine harness of certain vehicles. To eliminate this concern, separate the A/F sensor signal lines from the emission harness by installing the short cord
service part detailed in this bulletin.
Customers having this concern should have their vehicle repaired using the following repair procedure.
Page 1 of 20
CONSUMER NOTICE: The information and instructions in this bulletin are intended for use by skilled technicians. Mazda technicians utilize the proper tools/
equipment and take training to correctly and safely maintain Mazda vehicles. These instructions should not be performed by “do-it-yourselfers.” Customers
should not assume this bulletin applies to their vehicle or that their vehicle will develop the described concern. To determine if the information applies,
customers should contact their nearest authorized Mazda dealership. Mazda North American Operations reserves the right to alter the specifications and
contents of this bulletin without obligation or advance notice. All rights reserved. No part of this bulletin may be reproduced in any form or by any means,
electronic or mechanical---including photocopying and recording and the use of any kind of information storage and retrieval system ---without permission in
writing.
Bulletin No: 01-006/15
Last Issued: 04/24/2015
© 2015 Mazda Motor of America, Inc.
REPAIR PROCEDURE
Summary:
1. Verify that DTC P219A:00 and/or P219B:00 is stored in PCM memory.
NOTE:
•
•
The repairs are slightly different depending on which DTC is stored in PCM memory. Be sure to
proceed to the correct repair for the DTC that is found.
If both DTCs are stored in PCM memory, complete both repairs in this bulletin.
2. Remove (pull out) four (4) terminals from PCM connector 0140-010B.
3. Replace the four (4) removed terminals with the correct four (4) short cord terminals.
4. Route the short cord (A) from connector 0140-010B and the A/F sensor connector 0140-24 (for DTC
P219A:00) OR connector 0140-25 (for DTC P219B:00).
For DTC P219A:00
For DTC P219B:00
5. Pull out two (2) A/F Sensor terminals (C and E) from connector 0140-24 (for DTC P219A:00) OR connector
0140-25 (for DTC P219B:00), then install them into the short cord connector.
Page 2 of 20
Bulletin No: 01-006/15
Last Issued: 04/24/2015
© 2015 Mazda Motor of America, Inc.
REPAIR PROCEDURE FOR DTC P219A:00:
Wiring Diagram:
(A) = Install short cord
(B) = A/F Sensor (RH) terminals C and E
1. Verify that DTC P219A:00 is stored in PCM memory.
2. Record the customers preset radio stations.
3. Remove the engine cover.
4. Disconnect the negative battery cable.
5. Remove the battery and battery tray.
6. Remove the air cleaner element assembly.
7. DTC P219A:00 only: Remove the resonance chamber (A) and dynamic chamber (B) according to MS3
online instructions or the Workshop Manual (section 01-13 INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [MZI-3.7]).
Page 3 of 20
Bulletin No: 01-006/15
Last Issued: 04/24/2015
© 2015 Mazda Motor of America, Inc.
8. Disconnect connector 0140-010B from the PCM.
9. Remove the four (4) terminals (shown below) from connector 0140-010B.
NOTE: Refer to “How to remove terminals” below.
No.
Wire Color
1
2BD
White/Blue
2
2AS
Gray/Blue
3
2AG
White/Red
4
2AC
White/Green
Page 4 of 20
Bulletin No: 01-006/15
Last Issued: 04/24/2015
© 2015 Mazda Motor of America, Inc.
How to remove terminals:
a. Lift up the lock cover (A) using a thin flat-blade screwdriver (B), then remove cover from connector.
b. Release the lock lever (A) using the screwdriver (B), then pull the terminal (C) out of the connector.
Page 5 of 20
Bulletin No: 01-006/15
Last Issued: 04/24/2015
© 2015 Mazda Motor of America, Inc.
10. Install the four (4) terminals (shown below) from the short cord into the removed terminals from connector
0140-010B. Refer to the below table for terminal location and short cord wire colors.
No.
Wire Color
Short Cord Wire Color
1
2BD
White/Blue
Brown/Blue
2
2AS
Gray/Blue
White
3
2AG
White/Red
Violet/Green
4
2AC
White/Green
White/Green
11. Insert the lock cover over the connector, then push the cover down as shown below.
Page 6 of 20
Bulletin No: 01-006/15
Last Issued: 04/24/2015
© 2015 Mazda Motor of America, Inc.
12. Tape the remaining four (4) terminals of connector 0140-010B with electrical tape, then attach them to the
harness as shown below.
13. Route the short cord (A) as shown below.
14. Disconnect the A/F connector 0140-24 (A), then (push) release the lock lever (B) to move from the harness.
Page 7 of 20
Bulletin No: 01-006/15
Last Issued: 04/24/2015
© 2015 Mazda Motor of America, Inc.
15. Remove terminals C (Green) and E (Green/Brown) from connector 0140-24.
How to remove terminals:
a. Lift up the lock cover (A) using a thin flat-blade screwdriver, then remove cover from connector.
b. Release the lock lever using the screwdriver, then pull the terminal out of the connector.
Page 8 of 20
Bulletin No: 01-006/15
Last Issued: 04/24/2015
© 2015 Mazda Motor of America, Inc.
16. Insert the removed terminals from connector 0140-24 into the short cord connector.
How to insert terminals into short cord connector:
a. Lift up the short cord connector lock cover (A) half way.
b. Insert the terminals (A) into the connector, then push the lock cover down.
17. Connect the short cord connector to harness connector 0140-24.
18. Cut off the original connector 0140-24, then discard it.
19. Tape the ends of the remaining four (4) terminals (A) from the original connector 0140-24, then attach them
to the harness using electrical tape as shown below. (B) = short cord connector location.
Page 9 of 20
Bulletin No: 01-006/15
Last Issued: 04/24/2015
© 2015 Mazda Motor of America, Inc.
20. Using black tie-wraps (A), attach the short cord to the harness as shown below.
a. PCM side:
b. Starter motor side:
c. On Engine:
Page 10 of 20
Bulletin No: 01-006/15
Last Issued: 04/24/2015
© 2015 Mazda Motor of America, Inc.
21. DTC P219A:00 only: Reinstall the resonance chamber (A) and dynamic chamber (B) according to MS3
online instructions or the Workshop Manual (section 01-13 INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [MZI-3.7]).
NOTE: Be sure to replace the three (3) dynamic chamber gaskets with new ones.
22. Reinstall the air cleaner element assembly.
23. Reinstall the battery and battery tray.
24. Reconnect the negative battery cable.
25. Reinstall the engine cover.
26. Re-enter the customers preset radio stations.
27. Verify the repair.
Page 11 of 20
Bulletin No: 01-006/15
Last Issued: 04/24/2015
© 2015 Mazda Motor of America, Inc.
REPAIR PROCEDURE FOR DTC P219B:00:
Wiring Diagram:
(A) = Install short cord
(B) = A/F Sensor (LH) terminals C and E
1. Verify that DTC P219B:00 is stored in PCM memory.
2. Record the customers preset radio stations.
3. Remove the engine cover.
4. Disconnect the negative battery cable.
5. Remove the battery and battery tray.
6. Remove the air cleaner element assembly.
Page 12 of 20
Bulletin No: 01-006/15
Last Issued: 04/24/2015
© 2015 Mazda Motor of America, Inc.
7. Disconnect connector 0140-010B from the PCM.
8. Remove the four (4) terminals (shown below) from connector 0140-010B.
NOTE: Refer to “How to remove terminals” below.
No.
Terminal Location
Wire Color
1
2BF
Yellow/Violet
2
2AO
Violet/Yellow
3
2AK
White/Violet
4
2AE
Violet/White
Page 13 of 20
Bulletin No: 01-006/15
Last Issued: 04/24/2015
© 2015 Mazda Motor of America, Inc.
How to remove terminals:
a. Lift up the lock cover (A) using a thin flat-blade screwdriver (B), then remove cover from connector.
b. Release the lock lever (A) using the screwdriver (B), then pull out the terminal (C) out of the connector.
Page 14 of 20
Bulletin No: 01-006/15
Last Issued: 04/24/2015
© 2015 Mazda Motor of America, Inc.
9. Insert the four (4) terminals from the short cord into the removed terminals from connector 0140-010B.
Refer to the below table for terminal location and short cord wire colors.
No.
Wire Color
Short Cord Wire Color
1
2BF
Yellow/Violet
Brown/Blue
2
2AO
Violet/Yellow
White
3
2AK
White/Violet
Violet/Green
4
2AE
Violet/White
White/Green
10. Insert the lock cover over the connector, then push the cover down as shown below.
Page 15 of 20
Bulletin No: 01-006/15
Last Issued: 04/24/2015
© 2015 Mazda Motor of America, Inc.
11. Tape the remaining four (4) terminals of connector 0140-010B with electrical tape, then attach them to the
harness as shown below.
12. Route the short cord (A) as shown below.
13. Disconnect the A/F connector 0140-25 (A), then (push) release the lock lever (B) to move from the harness.
Page 16 of 20
Bulletin No: 01-006/15
Last Issued: 04/24/2015
© 2015 Mazda Motor of America, Inc.
14. Remove terminals C (Green) and E (Gray/Violet) from connector 0140-25.
How to remove terminals:
a. Lift up the lock cover (A) using a thin flat-blade screwdriver, then remove cover from the connector.
b. Release the lock lever using the screwdriver, then pull out the terminal out of the connector.
Page 17 of 20
Bulletin No: 01-006/15
Last Issued: 04/24/2015
© 2015 Mazda Motor of America, Inc.
15. Insert the removed terminals from connector 0140-25 into the short cord connector.
How to insert terminals into short cord connector:
a. Lift up the short cord connector lock cover (A) half way.
b. Insert the terminals (A) into the connector, then push the lock cover down.
16. Connect the short cord connector to harness connector 0140-25.
17. Cut off the original connector 0140-25, then discard it.
18. Tape the ends of the remaining four (4) terminals (A) from the original connector 0140-25 and attach them to
the harness using electrical tape as shown below. (B) = short cord connector location.
Page 18 of 20
Bulletin No: 01-006/15
Last Issued: 04/24/2015
© 2015 Mazda Motor of America, Inc.
19. Using black tie-wraps (A), attach the short cord to the harness as shown below.
a. PCM side:
b. Starter motor side:
c. On engine:
Page 19 of 20
Bulletin No: 01-006/15
Last Issued: 04/24/2015
© 2015 Mazda Motor of America, Inc.
20. Reinstall the air cleaner element assembly.
21. Reinstall the battery and battery tray.
22. Reconnect the negative battery cable.
23. Reinstall the engine cover.
24. Re-enter the customers preset radio stations.
25. Verify the repair.
PART(S) INFORMATION
Part Number
Description
Qty.
Notes
TGY1-67-SH1
Short Cord
1 or 2
For DTCs P219A:00 and/or P219B:00
CY01-13-135
Gasket
3
Replacement parts for DTC P219A:00 repair only
WARRANTY INFORMATION
NOTE:
•
•
•
This warranty information applies only to verified customer complaints on vehicles eligible for warranty repair.
This repair will be covered under Mazda’s New Vehicle Limited Warranty term or California Emission Defects Warranty (Long Term).
Additional diagnostic time cannot be claimed for this repair.
Warranty Type
A
Symptom Code
14
Damage Code
9Q
DTC
P219A:00 - (for DTC P219A:00)
P219B:00 - (for DTC P219B:00)
P219A:00 - (for DTC P219A:00 and P219B:00)
Part Number Main Cause
Quantity
Operation Number / Labor
Hours:
TGY1-67-SH1
1 or 2
XXJCHXRX / 1.5 Hrs. - (for DTC P219A:00 only)
XXJCJXRX / 0.9 Hrs. - (for DTC P219B:00 only)
XXJCKXRX / 1.9 Hrs. - (for DTC P219A:00 and P219B:00)
Page 20 of 20
- Formulated for engines with 75,000 miles or more, Valvoline...
- Delivers 20% better wear protection and 15% better sludge...
- Extra detergents safeguard against friction, corrosion and...
- Advanced friction-fighting additives help maximize...
- Provides performance benefits for high mileage, new and...
- Advanced protection against the four main causes of engine...
- Delivers 40% stronger wear protection than industry...
- Provides 15% better deposit defense vs. industry standards...
- Up to 2.5X better heat protection vs. industry standards to...
- Engineered for excellent low-temperature flow, reducing...
Last update on 2026-06-12 / Affiliate links / Images from Amazon Product Advertising API
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: 01-006-15-3039
Replacement Service Bulletin Number:
MFR Communication Date: 2015-04-24
MFR Internal Campaign ID/Software Version:
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- Obd2 Bluetooth Scanner Lifetime Update: Ediag Elite offers revolutionary Advantage Lifetime Updates with unlimited access to the superior 15 reset service, bidirectional testing and full system diagnostics.The Ediag Elite is an excellent Bluetooth obd2 scanner diagnostic tool ideal for diy's and private car owners
- Bidirectional Control for Quickly Locating Problems: The Bidirectional Scan tool allows you to send commands directly from your smartphone to your vehicle for active testing. This feature helps to quickly narrow down problems such as air conditioning clutches, windows, doors, sunroofs, etc., reducing diagnostic time for mechanics and helping Diy users locate faults more easily. In addition, Ediag Elite provides fault analysis and repair guidance to help you solve problems efficiently.
- 15 Maintenance Resets: The current version introduces 15 popular special features: Oil Reset, Headlight Matching, Bleeding Reset, TPMS Reset, BMS Reset, Gear Box Relearn, Throttle Learning, Injector Coding, SAS Reset and more special functions in system diagnose menu. These functions make it easy for owners to carry out the necessary maintenance and servicing, ensuring that your vehicle stays in top condition, prolonging its service life and preventing common problems and breakdowns. Note: The Special function vary by model& year, Reach us check compatibility.
- Wide Compatibility CANFD & FCA
Autoauth: Compatible with GM, Ford, Toyota, Chrysler, Honda, Mazda, Nissan, Mitsubishi, Hyundai, KIA with standard OBD2 port from 1996 to newer. More car brands and features will be released gradually. Newest Ediag Elite scanner supports CANFD Protocol and FCA cars. Note: Coverage may vary on different vehicle by model& year ,Please contact us to confirm compatibility before purchase. - Perfect for Monitoring The Health of Your Vehicle: Ediag Elite is designed to make vehicle maintenance simple and efficient. With intelligent AutoVIN quick recognition, it is easy to connect to your car without the need for manual input. Real-time data is visualized in a variety of formats, including graphs, numeric, meter displays and clear 4-in-1 data charts, allowing you to effortlessly monitor real-time data. Data logging/reporting is available for playback and further analysis.
- No Annual Fees & 2026 Upgraded CAN FD: Why pay $199/year or more for updates? The 2026 newest Kingbolen K7 obd2 scanner features have been upgraded to Lifetime Updates without subscription fees, saving you significant costs in the long run. K7 scan tool also adds the CAN FD protocol for the latest GM models (2019+), enabling faster data transfer, reducing the risk of undetected errors
- 2026 Newest Top-tier Car Scanner: Kingbolen K7 diagnostic scan tool is equipped with most capabilities for daily repair/maintenance: Wireless diagnosis via Bluetooth, Bidirectional Test, ECU Online/Offline Code, 31+ Resets, PMI for Ford, Lincoln, Mazda, Global version for 100+ brand vehicles and 17 languages, no area limit, FCA AutoAuth
- OE-Level Full Systems Scan Tool: K7 professional diagnostic scanner with Auto Vin can do one-click to scan ECUs on most of vehicles, like pcm, ecm, eps, bcm, tpms, sas, a/c system... to read/clear code, view live data, freeze frame, read ecu info. 4-in-1 data stream graphics can make data viewing more intuitive. Detailed diagnostic reports will help you easily master the car situation as it can be shared by bluetooth or email! Adding workshop information can help your customers to know more
- Bidirectional Test/Active Test & ECU Code: Stop guessing and start fixing. Bidirectional scan tool Kingbolen K7 can perform real active test that can send commands to the vehicle's ECU to drive the actuators to work, like window, rear mirrors, sunroof, door, solenoids, wipers, headlamp, etc, helping you quickly find out bad parts and pinpoint faulty issues. K7 bidirectional scanner will be a good choice to save money and time on car repairs when performing complex maintenance and repair
- 31 Reset Functions: Avoid expensive dealership visits for simple services. Experience tells us that just a small repair service may cost a lot of money. Kingbolen K7 is a professional diagnostic scanner with 31 common maintenance services like Oil /SAS/EPB/TPMS Reset, Battery Matching, ABS Bleeding, Injector Code, etc. It effectively handles most of the car reset and relearning jobs, perfect for experienced DIYers and mechanics. Note: Functions in the menu vary across vehicles. Kindly check the compatibility before purchase
- 【Cost-effective Diagnostic Scan Tool】Lifetime updates without fee, No subscription fee required, No IP restrictions, Ediag Elite bluetooth scanner stands out. It can perform in-depth Full System diagnostics,15+ Reset Services, powerful Active Test, CANFD & FCA AutoAuth. Connect your phone via Bluetooth for diagnosis, providing a faster, smarter and smoother diagnostic experience. Easy to put in pocket, convenient to carry, keep track of the car's status anytime, anywhere. Best bang for your bucks.
- 【15+ Reset Service, Easy Problem Solving】 KINGBOLEN Ediag Elite obd2 scanner diagnostic scan tool comes with 15+ professional reset functions, including: Oil Reset, ABS Bleeding, Injector Code, SAS Reset, TPMS Reset, BMS Reset, AFS Reset, Sunroof Calibration, Brake Reset and more special functions in system diagnose menu. The ideal bluetooth scanner for mechanics and DIY enthusiasts, which can save unnecessary maintenance costs and significantly shorten repair time.
- 【Comprehensive Full Systems Diagnostic】 The Ediag Elite obd2 scanner bluetooth supports full system In-Depth diagnosis. It can read/clear fault codes, read real-time data/freeze frame, module information, and perform testing and reset functions for ECM, BCM, ABS, SRS, TPMS, TCM, BMS, SAS, A/C & RTM systems ect. It works with most car models after 1996, cover more than 150+ car brands. Supports 22 global languages for your convenience(EN, FR, ES, DE, IT, RU, PT, JP, TU...)
- 【Powerful Bidirectional Scan Tool & Active Test】 The obd2 code reader for Ediag Elite can perform real time active test that can send commands to the vehicle’s ECU to drive the actuators to work, such as turn on the radiator fan, modulate the throttle, open/close windows, etc. It can help you quickly find out the bad components and the cause of the fault, which can save you a lot of time. With BT 5.2 wireless connectivity, you can enjoy wireless diagnostics up to 33 feet.
- 【FCA AutoAuth & CANFD Compatibility】 Ediag Elite scan tool offers support with FCA Gateway Access, allowing you to perform protected functions on FCA vehicles, including Chrysler, Dodge, Jeep, Alfa Romeo, Fiat vehicles, etc.(Note:just allows you to access the FCA, but need to have your own FCA account) Supports the CAN-FD protocol, provide high-speed vehicle diagnostic communication and data transfer, working perfectly on GM vehicles produced after 2020, saving $100 to buy a CAN FD adapter.
Last update on 2026-06-12 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.