@ACURA

Service Bulletin

January 28, 2017

16-060
05722 Version 3

Product Update: 2011 RL Software Update for Lock-up Clutch Function
Supersedes 16-060, dated January 17, 2017, to revise the information highlighted in yellow
Replaces 16-003, Torque Converter Shudder
AFFECTED VEHICLES
Year
Model
2011
RL

Trim
ALL

VIN Range
Check the iN VIN status for eligibility

REVISION SUMMARY
Under SOFTWARE INFORMATION, the software system was changed.

BACKGROUND
A surge, vibration, or judder may be felt while driving under light acceleration. To minimize the possibility for the judder
to occur, a software update for the transmission is available.
This product update does not have any warranty time or mileage limitations.
Additionally, the warranty on the torque converter in affected vehicles is being extended to 8 years from the original date
of purchase or 105,000 miles, whichever comes first. Refer to service bulletin 16-061, Warranty Extension: 2011 RL
Torque Converter for more information about the warranty extension.
There are two service bulletins applicable to this issue:
•
•

16-060, Product Update: 2011 RL Software Update for Lock-up Clutch Function - Update the software in the
vehicle and change the transmission fluid.
16-061, Warranty Extension: 2011 RL Torque Converter- Diagnose and, if needed, replace the torque converter.

Do 16-060 first to update the vehicle and replace the transmission fluid. If the judder returns after updating the vehicle,
the torque converter may need to be replaced; refer to 16-061 for diagnostic and repair information.

CLIENT NOTIFICATION
Owners of affected vehicles will be sent a notification of this campaign.
Do an iN VIN status inquiry to make sure the vehicle is shown as eligible.

CORRECTIVE ACTION
Update the AT software and change the ATF.
If the judder returns after the software update, refer to service bulletin 16-061, Warranty Extension: 2011 RL Torque
Converter to diagnose the torque converter.

CLIENT INFORMATION: The information in this bulletin is intended for use only by skilled technicians who have the proper tools, equipment,
and training to correctly and safely maintain your vehicle. These procedures should not be attempted by "do-it-yourselfers," and you should not
assume this bulletin applies to your vehicle, or that your vehicle has the condition described. To determine whether this information applies,
contact an authorized Acura automobile dealer.

© 2017 American Honda Motor Co., Inc. - All Rights Reserved

Page 1 of 5

PARTS INFORMATION
Part Name

Quantity

Part Number

Drain Plug Washer (18 mm)

904 71-PX4-000

1

ATF Fill Sealing Washer (24 mm)

90441-PK4-000

1

REQUIRED MATERIALS
Part Name

Part Number

Quantity

Acura ATF DW-1

08200-9008A

4

WARRANTY CLAIM INFORMATION
Operation
Number

Description

Flat
Rate
Time

Defect
Code

Symptom
Code

Template
ID

Failed Part Number

1255E0

Update the AT software,
then replace the ATF.

0.5 hr

6VA00

KB500

16-060N

37805-RK1-3050

SOFTWARE INFORMATION
NOTE: Unnecessary or incorrect repairs resulting from a failure to update the i-HDS or MVCI are not covered under
warranty.
i-HDS Software Version: 1.002.017 or later
J2534 Software Information:
PC Application Version 1.0.0.6 or later
Database update 19-DEC-2016 or later

Before beginning the repair, make sure that both the i-HDS and J2534 software are updated as listed above.
Do only the update listed in this service bulletin.
You cannot apply the updates with the MVCI as a standalone tool. To update the vehicle you must use the MVCI or
the DST-i interface in conjunction with the J2534 Rewrite Special PC application on the i-HDS.
For more information about updating
Updating Control Units/Modules.
Trim
Technology
Advance

the i-HDS, the MVCI, and vehicle systems, refer to Service Bulletin 01-026,

Software System
AT
AT

Program ID (or later)
KGA750
KGA950

Program P/N (or later)
37806-RKG-A 750
37806-RKG-A950

Page 2 of 5

REPAIR PROCEDURE

NOTE:
• You can't update the vehicle using the MVCI as a standalone tool.
•
Do not use the MongoosePro VCI tool.
•
Make sure the 12-volt battery is fully charged before starting an update.
•
Connect a fully charged jumper battery to the vehicle, and leave it connected during the entire procedure to
maintain steady voltage.
•
Never turn the ignition to OFF or ACCESSORY during the update. If there is a problem with the update, leave the
ignition turned to ON.
• To prevent PCM damage, do not operate anything electrical (headlights, audio system, brakes, A/C, power
windows, door locks, etc.) during the update.
•
If you see the following Error Display, check that you are using the correct tool (MVCI or DST-i) with the i-HDS.
Error Display

Error50
DATA LINK COMMUNICATION ERROR
Make sure correct VCI device Is selected in the settings menu .
Make sure that the Ignition switch is on, and retry programming.
Press ENTER.
System :
Current Program ID :

Program JD :
Model :

Update Description :

Back

Help

Next

To change this, click on either of the SETTING selection buttons at the bottom of the J2534 initial screens as
shown.
HONDA

HONDA

Honda ECU Reprognvnming

E""'• "'"' Sffviui ~1-n ,...._

Do nor emer bullelin number

WARNING
Do r:ot perform CM Upc1t1H -!ltr()oSS .any type 0f wtre!Us eonnedlOn betv.een Iha ll!lptOJI end tile lnltnfe«i de'i1ee.

lf ;1

It. d151llpl'i