Sequoia
1 Remove disc brake anti-rust covers/anti-corrosion
wheel film……………………………………………………..
2 Inspect tires for defects/damage ……………………………
3 Initialize Tire Pressure Warning System (TPWS) (see
page 2) ………......................................................................
4 Install wheel covers/caps/spare tire wheel covers* ……….
5 Inspect for fuel, oil, coolant, and other fluid leaks …………
6 Inspect under the vehicle for damage, rust, etc ……………
7 Visually check bolts and nuts on chassis and powertrain
for looseness…………………………………………………….
8 Install rubber body plugs (stored in glove box or center
console)*………………………………………………………..

FUNCTIONAL OPERATION
Apply parking brake and cycle ignition “IG-ON”; place gear selector in reverse; turn
on lights and rear defogger. Unlock doors; release fuel door, release rear hatch.

5
6
7
8
9
10
11

OK

UNDER VEHICLE (ON HOIST)

1 Install Short Pin (see page 2)………………………………...

1
2
3
4

September 2015
Adjust\
Repair

OK

BEFORE INSPECTION

Adjust\
Repair

2016 PRE-DELIVERY SERVICE CHECK SHEET

Check dome, courtesy, map, and sun visor lights*………...
Check warning/indicator lights, gauges, and horn.…..…….
Check windshield wipers and washers..……………………
Check headlights, instrument lights, turn signals,
emergency flashers, and brake lights ……………………….
Check inside/outside rear view mirror operation/
adjustment*……………………………………………………..
Check cigarette lighter* and power outlets………………….
Check audio/navigation*/backup camera* systems and
set clock.………………….……………………………………
Install shift-lock override button cover ………... ……….…...
Check sliding roof* …………………………………………….
Check Rear Seat Entertainment system operation*
Check Parking Assist system* ………………..…………...

ROAD TEST
A complete road test helps assure customer satisfaction. Drive vehicle over a
variety of road surfaces and driving conditions. Check for unusual noise and driving
performance.
Enter Odometer Readings
Reading Before Test: _______________ Reading After Test: ________________

1
2
3
4
5
6
7
8
9
10
11
12
13
14

WALKAROUND INSPECTION
Starting at the left front door, check window and door lock operation. Continue
around the vehicle in a counterclockwise direction checking each door and window
operation, child door locks, seat belts, interior condition, all lights, and luggage
compartment contents. Finish by checking headlight aim and continue into UNDER
HOOD checks.

1 Check Smart Key System…………………………………...
2 Check door and door lock operation, including each
wireless remote control/theft deterrent system*…………….
3 Check window operation………………………………………
4 Check that engine starts with all keys ……………….………
5 Check that child safety door locks are in normal (unlocked)
position……………………………………………………….….
6 Check seats and seat belt operation………………………...
7 Check rear defogger*/rear view mirror defogger*…………..
8 Check side marker, tail, backup, and license plate lights …
9 Check luggage compartment light* and trim appearance…
10 Adjust spare tire pressure, inspect for damage, and check
jack and tool installation………………………………………
11 Check headlight aim…………………………………………...

Check cold engine operation …………………………………
Check engine operation during warm-up ……………………
Check engine at normal operating temperature ……………
Check automatic transmission operation ………………...….
Check brake and parking brake operation ………………….
Check steering operation and off-center/vehicle pull/flutter
Inspect for abnormal noise and vibration ……………………
Inspect for squeaks and rattles ………………………………
Check front and rear* heater and A/C operation……………
Check cruise control operation...……………………………...
Check Blind Spot Monitor system*……………………………
Check front seat heater/ventilation operation* ……………..
Set/calibrate compass* (see page 2)………………………..
Check rear height control air suspension*……………………

FINAL INSPECTION AND CLEANING
1 Remove interior protective covers, unnecessary labels,
tags, etc. (Remove just before delivery to customer) ………
2 Visually inspect all interior parts for installation, damage, fit,
dirt, etc.…………………………………………………………..
3 Verify floor mat application and install using retaining
clips*…………………………………………………………….
4 Remove Rapgard™ and clear protective bumper film*……
5 Wash and clean vehicle……………………………………….
6 Inspect paint finish for scratches, chips, rust, dents,
damage, etc……………………………………………………
7 Inspect exterior body parts for proper installation, damage,
rust, etc………………………………………………………….
8 Place oil change sticker on inside of windshield, top left
corner……………………………………………………………
9 Place Owner’s Guide and first aid kit portfolio* in glove box
10 Perform Techstream Health Check…………………………..
11 Install front license plate and mounting bracket*
(see page 2)…………………………………………………..

UNDER HOOD
1
2
3
4
5

Check engine oil level…………………………………………
Check brake and power steering* fluid levels……………....
Check engine coolant level …………………………………..
Check windshield washer fluid level…………………………
Check battery state-of-charge using Digital Battery
System Analyzer (SOC Reading: ___________%) ……
6 Inspect for fuel, oil, coolant, and other fluid leaks………….
* Inspect or install when equipped/required.

Completion and retention of this form is required to comply with Toyota’s Warranty Policy.
TECHNICIAN’S SIGNATURE

NAME (PLEASE PRINT)
Date

Dealer Name

SERVICE MANAGER’S SIGNATURE

We hereby certify that all items
on this form have been
checked and corrected for
proper operation as required.

NAME (PLEASE PRINT)
Dealer Code

Vehicle Identification Number (Sticker)

SHORT PIN INSTALLATION
To minimize battery discharge the Short Pin has been removed
and is stored in the engine compartment Relay Block.
Install the Short Pin.
NOTE
If the vehicle is stored in the dealership for a long
period of time after PDS, disconnect the negative
(–) battery terminal to prevent battery discharge.
Refer to Service Bulletin No.
PG001-06, “Battery Maintenance for In-Stock
Vehicles & Pre-Delivery,” for battery maintenance
information.

TIRE PRESSURE WARNING SYSTEM (TPWS) INITIALIZATION
Refer to the Repair Manual for the Initialization procedure. Please note the spare tire does not have a TPWS sensor.
NOTE
To adjust tire pressure correctly when outside temperature is significantly colder or warmer than shop
temperature, perform a Health Check using Techstream and select the “Compensation Tire Pressure”
checkbox. The compensation pressures will be displayed on the Health Check results screen. Adjust the tire
pressure when the tires are cold.

COMPASS CALIBRATION
Refer to the Repair Manual for the Calibration procedure for vehicles equipped with a compass in the rear view mirror.
NOTE
 Do NOT perform calibration of the compass in a place where the Earth’s magnetic field is subject to
interference (underground parking, under a steel tower, between buildings, roof parking, near a railroad
crossing, near a large vehicle, etc.).
 During calibration, do NOT operate electric systems (moon roof, power windows, etc.) as they may interfere with the
calibration.

FRONT LICENSE PLATE AND MOUNTING BRACKET INSTALLATION*
The bracket and 6 mounting screws are placed in a vinyl bag located on the right front passenger’s side floor.
Installation Procedure
1. Attach the license plate bracket by snapping the clips on the
top of the bracket onto the lower lip of the air intake opening
on the bumper.
2. Align the 4 mounting holes in the bracket with the 4 dimples in
the bumper.
3. Screw two 20 mm (0.787 in.) self-tapping mounting screws (A)
into the top holes on the bumper and then screw the two 30 mm
(1.81 in.) self tapping screws (B) into the bottom holes.
4. Align the mounting holes in the license plate with the
corresponding holes in the bracket. Using the 2 remaining
20 mm (0.787 in.) self-tapping screws (A), mount the license
plate directly to the bracket assembly.
NOTICE
 Do NOT pre-drill holes into the bumper.
 Do NOT overtighten the self-tapping screws.