ATTENTION:
GENERAL MANAGER
PARTS MANAGER
CLAIMS PERSONNEL
SERVICE MANAGER

q
q
q
q

IMPORTANT - All
Service Personnel
Should Read and
Initial in the boxes
provided, right.

SERVICE BULLETIN
APPLICABILITY:
SUBJECT:

2008-2013MY Impreza WRX and STI Models
ront Bumper Fascia Excess Gap Repair
F
Procedures

NUMBER:
DATE:

12-141-12
10/25/12

INTRODUCTION
This bulletin provides a procedure to repair a gap which may develop between the front bumper
fascia and the fender. Also included is a repair procedure to prevent recurrence of peeling paint film
at the rear corner of the front bumper fascia where it may come in contact with the bottom of the
fender.
PART INFORMATION

Peeling

PART NUMBER

DESCRIPTION

57707FG122

Brkt-SD, R/Hand

57707FG132

Brkt-SD, L/Hand

57704FG113

Bumper Face

91180AG000

Cushion Tape

Continued...
CAUTION: VEHICLE SERVICING PERFORMED BY UNTRAINED PERSONS COULD
RESULT IN SERIOUS INJURY TO THOSE PERSONS OR TO OTHERS.
Subaru Service Bulletins are intended for use by professional technicians ONLY. They
are written to inform those technicians of conditions that may occur in some vehicles, or
to provide information that could assist in the proper servicing of the vehicle. Properly
trained technicians have the equipment, tools, safety instructions, and know-how
to do the job correctly and safely. If a condition is described, DO NOT assume that this
Service Bulletin applies to your vehicle, or that your vehicle will have that condition.

Bulletin Number: 12-141-12; Date: 10/25/12

SUBARU OF AMERICA, INC. IS
“ISO 14001 COMPLIANT”
The international standard for excellence
in Environmental Management Systems.
Please recycle or dispose of automotive
products in a manner that is friendly to our
environment and in accordance with all
local, state and federal laws and regulations.

Page 1

SERVICE PROCEDURE / INFORMATION
If a gap is verified between the bumper fascia and the fender as shown in the left hand photo on page
1, it is likely the fascia has come loose from the side mounting bracket(s).
NOTE: Inspect the vehicle for any collision-related factors or other outside influence which may
effect the fit of the front bumper fascia before proceeding.
•

Follow the procedures in the applicable Service Manual to remove the front bumper fascia.
IMPORTANT: Be sure to protect the headlamp lenses with vinyl tape as shown in the photo
below in the areas where they may be contacted or scratched by the top corners of the front
bumper fascia during removal. An illustration of the revised front bumper fascia side mounting
bracket is shown below, right.
Revised Front
Bumper Fascia
Side Mounting
Bracket

•

If the vehicle was manufactured before October, 2010, replace the front bumper fascia along
with the side mounting brackets.

•

If the vehicle was manufactured between October, 2010 and November, 2011, replace only the
side mounting brackets.

•

IMPORTANT: Regardless of the vehicle’s production date, closely inspect the attachment
points of both the front bumper fascia and the side mounting brackets for damage. If any
are damaged or broken, replace the front bumper fascia and / or the side mounting brackets
as necessary.

Continued...
Bulletin Number: 12-141-12; Date: 10/25/12

Page 2

•

If there is any peeling of the paint film on the corner of the front bumper fascia, regardless of the
vehicle’s production date, cut to size then apply the cushion tape as shown in the illustrations
below. IMPORTANT: Be sure to clean any dirt or grease from the cushion tape mounting
surfaces before application.

•

Touch up the peeling paint as necessary.
Top view of Cushion Tape Installation

Front Bumper
Fascia

(25mm)

•

Reinstall the front bumper fascia. Because of the increased interlocking force applied by the
revised components, more effort may be required to get it properly “locked” into position.

•

Remove the protective vinyl tape from the headlights to complete the procedure.

WARRANTY / CLAIM INFORMATION
For vehicles within the Basic New Car Limited Warranty period, this repair may be claimed using the
following information.
LABOR DESCRIPTION

LABOR OPERATION #

Front Bumper Cover R&R for Gap Repair,
Includes Cushion Tape Application

B916-971

0.4

Replace One or Both Front Bumper
Cover Side Brackets

C916-973

0.1

Color Coat & Replace Front Bumper Cover,
Includes Transfer of All Components

C984-106

1.9

Sublet Repair - Administration Expenses

C101-108

0.3

Bulletin Number: 12-141-12; Date: 10/25/12

FAIL CODE

LABOR TIME

XAW-48

Page 3