Page 1 of 2

TECHNICAL BULLETIN
JTB00495NAS1
06 JUN 2016
© Jaguar Land Rover North America, LLC
NOTE: The information in Technical Bulletins is intended for use by trained, professional Technicians with the knowledge,
tools, and equipment required to do the job properly and safely. It informs these Technicians of conditions that may occur on
some vehicles, or provides information that could assist in proper vehicle service. The procedures should not be performed by
'do-it-yourselfers'. If you are not a Retailer, do not assume that a condition described affects your vehicle. Contact an
authorized Jaguar service facility to determine whether this bulletin applies to a specific vehicle.

SECTION: 309-00B

Exhaust System Noise Reduction
AFFECTED VEHICLE RANGE:
F-TYPE (X152)
Model Year:
2014-2015
VIN:
K00001-K22184
Assembly Plant: Castle Bromwich

V8 S/C 5.0L Petrol

MARKETS:
NAS

CONDITION SUMMARY:
Situation: The exhaust system noise may be reduced.
Cause: This may be caused by incorrect software.
Action: Should a customer express this concern, follow the Service Instruction below.

PARTS:
No Parts Required

TOOLS:
NOTE: This Active Bulletin will display a functional programming shortcut if accessed within a
diagnostic session.
Jaguar Land Rover-approved diagnostic tool with latest DVD and Calibration File
Jaguar Land Rover-approved Midtronics battery power supply

WARRANTY:
NOTE: Repair procedures are under constant review, and therefore times are subject to
change; those quoted here must be taken as guidance only. Always refer to TOPIx to obtain the
latest repair time.
NOTE: DDW requires the use of causal part numbers. Labor only claims must show the causal
part number with a quantity of zero.
DESCRIPTION

SRO

TIME
(HOURS)

CONDITION
CODE

CAUSAL
PART

Configure Existing Powertrain Control
Module

86.99.26

0.2

42

C2D30319

NOTE: Normal Warranty procedures apply.

SERVICE INSTRUCTION:

http://topix.jaguar.jlrext.com/topix/service/document/658687

6/28/2016

Page 2 of 2

CAUTION: A Jaguar Land Rover-approved Midtronics battery power supply must be connected to
the vehicle battery during diagnosis / module programming.
CAUTION: Ensure all ignition ON/OFF requests are carried out; failure to perform these steps may
cause damage to control modules in the vehicle.
NOTE: The Jaguar Land Rover-approved diagnostic tool must be loaded with DVD145.07 v.240 or
later.
NOTE: Use DDW to check for Recall, Service Action, or Update Prior to Sale notice eligibility
requiring a Powertrain Control Module (PCM) software update. If eligible, perform and claim the PCM
update as per that program.

1. Connect the Jaguar Land Rover-approved Midtronics battery power supply to the vehicle battery.

2. Turn ignition ON (engine not running).

3. Connect the Jaguar Land Rover-approved diagnostic tool to the vehicle and begin a new session.

4. Follow the on-screen prompts, allowing the diagnostic tool to read the VIN, identify the vehicle, and
initiating the data collect sequence.

5. Select 'Diagnosis' from the Session Type screen.

6. Select the 'Selected Symptoms' tab and then select:
• Powertrain - Engine system - Emissions - Exhaust noises
7. Select 'continue'.

8. Select the 'Recommendations' tab and then select 'Run' to perform the 'Configure existing module Powertrain control module' option.

9. Follow all on-screen instructions to complete this task, ensuring all Diagnostic Trouble Codes (DTC) are
cleared.

10. When all tasks are complete, select the 'Session' tab and then select the 'Close Session' option.

11. Disconnect the diagnostic tool and battery power supply from the vehicle.

http://topix.jaguar.jlrext.com/topix/service/document/658687

6/28/2016