Final lnspectio

& Cleaning

Page 6 of 6

1. Remove interior protective covers, unnecessary labels, tags, etc. (Remove protective covers
just before delivery to the customer)
Remove plastic covers from door panels, seats, head restraints, and sun visors, as required.
I
I

I Remove labels, tags, and stickers (except those containing owner information).
NOTE

1

I
1

Consumer information labels, such as airbag information warning and bumper information
labels, MUST be left on the vehicle until delivery to a retail customer.

i

2.1 Visually inspect all interior parts for installation, damage, fit, dirt, etc.
3.1 Verify floor mat application and install using retaining clips* - T-SB-0023-13
4.1 Remove Rapgard™ and clear protective bumper film*
I

I Ensure that ALL glue residue is removed.

s. [Wash and

clean vehicle

I

6.) Inspect paint finish for scratches, chips, rust, dents, damage, etc.
i

7.1 Inspect exterior body parts for proper installation, damage, rust, etc.
8.I Place oil change sticker on inside of windshield, top left corner
i

I Complete the mileage or date recommendation and apply the oil change reminder sticker to the
i inside of the windshield, top left corner. You may use your current oil change reminder sticker.
!

9.f Place Owner's Guide and first aid kit portfolio* in glove box
i

10.1 Perform Techstream Health Check

I Perform
!I

Health Check to ensure that diagnostic trouble codes are not present. Health Check
results can be printed for the customer at delivery, or for the dealer file, using the Diagnostic
Report function.

I

11.l Install front license plate and mounting bracket* - see check sheet

*/ns~ect or install when equipped or required
I

© 2013 Toyota Motor Sales, USA

- --- I

®TOYOTA SEQUOIA
2014 PRE-DELIVERY SERVICE CHECK SHEET
01 Remove disc brake anti-rust c;;overs/anti-corrosion
wheel film .......................................................................
02 Inspect tires for defects/damage .................................... .
03 Initialize Tire Pressure Warning System (TPWS) (see
page2) ...................................................................
04 Install wheel covers/caps/spare tire wheel covers* ......... .
05 Inspect for fuel, oil, coolant, and other fluid leaks ........... .
06 Inspect under the vehicle for damage, rust, etc .............. .
07 Visually check bolts and nuts on chassis and powertrain
for looseness ...................................................................
08 Install rubber body plugs (stored in glove box or center
console)* ........................................................................

Apply parking brake and cycle ignition "IG-ON'~ place gear selector in reverse; turn
on lights and rear defogger. Unlock doors; release fuel door.

01 Check dome, courtesy, map, and sun visor lights* ......... .
02 Check warning/indicator lights, gauges, and horn .......... .
03 Check windshield wipers and washers ........................... .
04 Check headlights, instrument lights, turn signals,
emergency flashers, and brake lights ............................. .
05 Check inside/outside rear view mirror operation/
adjustment. ..................................................................... .
06 Check cigarette lighter and power outlets* ..................... .
07 Check audio/navigation*/backup camera* system and
set clock ......................................................................... .
08 Install shift-lock override button cover .......................... ..
09 Check sliding roof* ................................. : ...................... ..
10 Check Rear Seat Entertainment System operation* ..... ..
11 Check Parking Assist System* ....................................... .

DD
DD
DD
DD
DD
DD
DD
D
DD
DD
DD

wireless remote control/theft deterrent system* .............. .
03 Check window operation ................................................ .
04 Check that engine starts with all keys ............................ .
05 Check that child safety door locks are in normal
(unlocked) position* ........................................................ .
06 Check seats and seat belt operation ............................. ..
07 Check rear defogger*/rear view mirror defogger* ........... .
08 Check side marker, tail, backup, and license plate lights
09 Check luggage compartment light* and trim appearance
10 Check jack and tool installation ..................................... .
11 Check headlight aim ....................................................... .

01 Check engine oil level ............................................ .
02 Check brake and power steering* fluid levels ................ ..
03 Check engine coolant level. ............................................ .
04 Check windshield washer fluid level .............................. .
05 Check battery state-of-charge using Digital Battery
System Analyzer (SOC Reading: _ _ _ __
06 Inspect for fuel, oil, coolant, and other fluid leaks ........... .

D
DD
DD
D
DD
DD
DD
D

A complete road test helps assure customer satisfaction. Drive vehicle over a
variety of road surfaces and driving conditions. Check for unusual noise and
driving performance.

Enter Odometer Reading
Reading Before T e s t : - - - - - Reading After Test: _ _ _ _ __

01 Check cold engine operation .......................................... .
02 Check engine operation during warm-up ........................ .
03 Check engine at normal operating temperature ............. .
04 Check automatic transmission operation ........................ .
05 Check brake and parking brake operation ...................... .
06 Check steering operation and off-center/vehicle
pull/flutter ........................................................................ .
07 Inspect for abnormal noise and vibration ........................ .
08 Inspect for squeaks and rattles ....................................... .
09 Check front and rear* heater and NC operation ............. .
10 Check cruise control operation ....................................... .
11 Check Blind Spot Monitor System* ................................. .
12 Check front seat heater/ventilation operation* ................ .
13 Set/calibrate compass* (see page 2) ............................. .
14 Check rear height control air suspension* ..................... ..

Start at left front door. Check window and door lock operation (from master power
switch, if equipped). Continue around vehicle in a counterclockwise direction
checking each door and window operation, child door locks, seat belts, interior
condition, all lights, luggage compartment contents. Finish by checking headlight
aim and continue into UNDER HOOD checks.

01 Check Smart Key System* .................................... .
02 Check door and door lock operation, including each

July 2013

DD
DD
DD
DD
DD
DD
DD
DD
DD
DD
DD

01 Remove interior protective covers, unnecessary labels,
tags, etc. (Remove just before delivery to customer) ...... .

02 Visually inspect all interior parts for installation,
damage, fit, dirt, etc ........................................................ .
03 Verify floor mat application and install using
retaining clips* ...............................................................
04 Remove Rapgard™ ·and clear protective bumper film* ... .
05 Wash and clean vehicle ................................................. ..
06 Inspect paint finish for scratches, chips, rust, dents,
damage, etc.................................................................... .
07 Inspect exterior body parts for proper installation,
damage, rust, etc ............................................................ .
08 Place oil change sticker on inside of windshield, top
left corner ........................................................................
09 Place Owner's Guide and first aid kit portfolio*
in glove box ....................................................................
10 Perform Techstream Health Check ............................... .
11 Install front license plate & mounting bracket (see
page2) ........................................................................... .

DD
DD
DD
DD
DD
DD

* Inspect or install when equipped/required.

DD
DD
DD
DD
DD
DD
DD
DD
DD
DD
DD
DD
DD
DD
D
DD
DD
D
D

DD

DD
D

D

DD

D

Completion and retention of this from is required to comply with Toyota's Warranty Policy.

TECHNICIAN'S SIGNATURE

I

NAME (PLEASE PRINT)
Date

Dealer Name

We hereby certify that all items
on this form have been checked
and corrected for proper
operation as required.

SERVICE MANAGER'S SIGNATURE

I

NAME (PLEASE PRINT)
Dealer Code

I

Vehicle Identification Number (Sticker)

SHORT PIN INSTALLATION
To minimize battery discharge the Short Pin has been removed
and is stored in the engine compartment Relay Block.
Install the Short Pin.

NOTE
If the vehicle is stored in the dealership for a long period of
time after PDS , disconnect the negative(-) battery terminal
to prevent battery discharge. Refer to SeNice Bulletin No .
PG001-06, "Battery Maintenance for In-Stock Vehicles &
Pre-Delivery," for battery maintenance information.

1 Storage Location

2 Installation Location

TPWS INITIALIZATION
Refer to the Repair Manual for the Initialization procedure. Please note the spare tire does not have a TPvys sensor.

NOTE
To adjust tire pressure correctly when outside temperature is significantly colder or warmer than shop temperature,
perform a Health Check using Techstream and select the "Compensation Tire Pressure" checkbox. The compensation
pressures will be displayed on the Health Check results screen. Adjust the tire pressure when the tires are cold.

COMPASS CALIBRATION
Refer to the Repair Manual for the Cali bration procedu re for vehicles equipped with a compass in the rear view mirror.

NOTE
• Do NOT perform calibration of the compass in a place where the Earth's magnetic field is subject to interference
(underground parking , under a steel tower, between buildings, roof parking , near a railroad crossing , near a large
vehicle, etc.).
• During calibration , do NOT operate electric systems (moon roof, power windows, etc.) as they may interfere with the
calibration .

FRONT LICENSE PLATE AND MOUNTING BRACKET INSTALLATION
The bracket and 6 mounting screws are placed in a vinyl bag located on the right front passenger's side floor.
Installation Procedure

1. Attach the license plate bracket by snapping the clips on
the top of the bracket onto the lower lip of the air intake
opening on the bumper.
2. Align the 4 mounting holes in the bracket with the
4 dimples in the bumper.
3. Screw two 20 mm (0 .787 in .) self-tapping mounting screws
(A) into the top holes on the bumper and theri screw the
two 30 mm (1 .81 in.) self tapping screws (B) into the
bottom holes.
4. Align th e mounting holes in the license plate with the
corresponding holes in the bracket. Using the 2
remaining 20 mm (0 .787 in.) self-tapping screws (A),
mount the license plate directly to th e bracket assembly.
Length: 20.0 mm (0 .79 in.)
Diameter: 6.0 mm (0.24 in.)

NOTICE
• Do NOT pre-drill holes into the bumper.
• Do NOT overtighten the self-tapping screws.
1 License Plate
2 Screw A: 20 mm (0.787 in.)

3 Screw B: 30 mm (1 .81 in.)
4 Front License Plate
Mounting Bracket