File in Section:

Service Bulletin

-

Bulletin No.:

PIC5428F

Date:

May, 2014

PRELIMINARY INFORMATION
Subject:

EBCM Wheel Speed Sensor Diagnostic Aid for ABS Message -Click Or Ratchet NoiseService Traction Message - Service Stabilitrak Message - Service Steering Message

Models:

2008-2014 Buick Enclave
2010-2014 Buick LaCrosse
2011-2014 Buick Regal
2012-2014 Buick Verano (2014 MY: front driven wheel bearings only)
2013-2014 Cadillac ATS – AWD / RWD (driven wheel bearings only)
2014 Cadillac CTS (VIN A incl. V-Sport)
2008-2014 Cadillac CTS/CTS-V
2010-2014 Cadillac CTS Wagon
2011 2014 Cadillac CTS/CTS-V Coupe
2010-2014 Cadillac SRX (driven wheel bearings only)
2013-2014 Cadillac XTS
2010-2014 Chevrolet Camaro
2011-2014 Chevrolet Camaro Convertible
2009-2012 Chevrolet Colorado
2011-2014 Chevrolet Cruze, Volt (2014 MY: front driven wheel bearings only)
2010-2014 Chevrolet Equinox
2014 Chevrolet Impala (New Body Style)
2013-2014 Chevrolet Malibu
2009-2014 Chevrolet Traverse
2009-2014 GMC Canyon
2007-2014 GMC Acadia
2010-2014 GMC Terrain
2007-2010 Saturn Outlook
with any of the following DTCs or Symptom codes C0035 C0040 C0045 C0050 with
symptom bytes 18 5A 0F
This PI was superseded to update model list. Please discard PIC5428E.

The following diagnosis might be helpful if the vehicle exhibits the symptom(s) described in this PI.

Condition/Concern
Some customers may comment on any of the following conditions.
• The ABS, Service Traction Control System, and/or Service Stabilitrak telltale lights are on. During initial scan
for EBCM module diagnostic codes you may find one or more of the following DTCs C0035-C0050 with
specifically symptom bytes 18, 5A, 0F.
Note: For vehicles equipped with Electric Power Steering RPO NJ2 only - Operator may also notice a Service
Steering Message displaying in the Driver Information Center (DIC) and will experience heavier steering feel at low
speed or static steering maneuvers when this happens.
This will be accompanied with the Power Steering Control Module setting DTC U0415. This is a normal default
action with the loss of a Wheel Speed Sensor signal. If DTC U0415 remains after removal of the Wheel Speed
Sensor debris refer to published diagnostics.
• A brief and intermittent noise, click, ratchet, grind, or ABS pump motor noises typically heard from the inside of
the vehicle at parking lot speeds.

A flashing Traction Control or Stabilitrak telltale at low speeds.
The latter two conditions correspond with no reported EBCM / ABS / Stability DTCs set current or history.
These conditions may be caused by single or multiple pieces of ferrous metallic debris stuck to the wheel speed
sensor magnetic encoder ring. This magnetic encoder ring is now part of the inboard bearing hub assembly.
Note: NOTE: THIS INFORMATION IS NOT APPLICABLE TO CAPPED WHEEL BEARINGS.

3765975

(1.) Capped Wheel Bearing
Background Information:

2596034

(1.) Wheel Speed Sensor
Magnetic Encoder Ring - North and South Poles are shown
New Bearing Design.

2596032

(1.) Magnetic Encoder Ring
Some new model vehicles today have begun to use a different type of wheel speed sensor encoder ring or tone
wheel. Instead of a traditional mechanical type tooth tone wheel, the wheel speed sensor tone wheel is now made of
a magnetized nitrile rubber ring, typically brown in color. This magnetic encoder consists of multiple North and South
Pole pairs surrounding the outer circumference. When this magnetic encoder ring rotates and passes by the wheel
speed sensor head; it generates a sign wave in the wheel speed sensor. The wheel speed sensor converts an
analog signal to a digital square wave, and typical digital signal values switch between 7mA (Low) and 14mA (High)
DC current.

Recommendation/Instructions
Inspect and clean debris from the Encoder Ring.
Inspection and Cleaning Procedure:
Below inspection and cleaning procedure is supporting information to the SI wheel speed sensor diagnostic
mechanical fault table. In most cases the DTCs C0035-C0050 with symptom bytes 18, 5A, 0F can be repaired by
removing and/or cleaning any accumulated debris on the magnetic encoder ring; which is located on the inboard
side of the bearing hub.
Important: Most repairs can be performed without any replacement of the bearing hub assembly or wheel speed
sensor.
Caution: Take care not to damage the bearing outer seal when brushing and/or cleaning the magnetic encoder
debris
Do not use any type of magnetic tool to remove the debris from the bearing magnetic encoder; an external magnet
can damage the encoder.
BEFORE CLEANING

2596037

(1.) Sample Debris
1. Based on the specific EBCM module Wheel Speed Sensor DTC code; inspect the appropriate corner magnetic
encoder ring for possible debris.
– C0035 Left Front Corner
– C0040 Right Front Corner
– C0045 Left Rear Corner
– C0050 Right Rear Corner
2. If debris is found, perform the following cleaning recommendations.
Important: To properly clean the magnetic encoder ring, some applications may require removal of the bearing/hub
assembly. Refer to the specific Wheel Bearing and Hub Replacement procedure in SI.
2.1. Gently using a dry nylon soft bristle brush, remove the foreign debris off the magnetic encoder ring. If
debris was removed, proceed to step 3.
2.2. If debris still remains, wash the encoder ring using a mild soap detergent and wipe dry.
AFTER CLEANING

2596035

1. Connect a scan tool to the vehicle. Turn ON the ignition. Clear the DTCs.
2. Perform vehicle diagnostic repair verification procedure for DTC: C0035-C0050. Refer to SI.

Warranty Information
For vehicles repaired under warranty use:
Labor
Operation

* 2480068

* 2480078

Description

Inspect and Clean Debris From
Front Wheel Speed Sensor Encoder
Ring (One Side)

Inspect and Clean Debris From Rear
Wheel Speed Sensor Encoder Ring
(One Side)

Vehicle(s) Involved

Labor Time

Camaro, CTS VIN D (RWD), Colorado (RWD),
Canyon (RWD)

0.4 hr

SRX, Volt

0.7 hr

ATS (AWD), CTS VIN A/D (AWD), Acadia,
Enclave, Outlook, Traverse, Equinox, Terrain,
Cruze, Verano

1.0 hrs

LaCrosse, Regal

0.9 hr

Malibu

0.8 hr

Impala, XTS

1.6 hr

Colorado (4WD), Canyon (4WD)

1.9 hr

Acadia (FWD), Enclave (FWD), Outlook (FWD),
Traverse (FWD), SRX (FWD), LaCrosse (FWD),
Regal (FWD), Equinox (FWD), Terrain (FWD),
Malibu, Impala, XTS (FWD)

0.4 hr

Camaro, CTS VIN D, Equinox (AWD),
Terrain (AWD)

0.9 hr

SRX (AWD), ATS, CTS VIN A

1.1 hrs

LaCrosse (AWD), Regal (AWD)

2.1 hrs

Acadia (AWD), Enclave (AWD), Outlook (AWD),
Traverse (AWD)

1.0 hrs

Volt

0.8 hr

Cruze, Verano

0.6 hr

XTS (AWD)

1.4 hr

*This is a unique labor operation number for PI use only. This will not be published in the Labor Time Guide.

Please follow this diagnostic or repair process thoroughly and complete each step. If the condition exhibited is
resolved without completing every step, the remaining steps do not need to be performed.