File in Section:

Service Bulletin

Bulletin No.:
Date:

PI0756A
October, 2012

PRELIMINARY INFORMATION
Subject:

Retrofit Procedure for New Corded Folding Top Cover Installation to Original Design
Frame

Models:

2011-2012 Chevrolet Camaro Convertible

This PI is being revised to provide updated repair and warranty information. Please discard
PI0756.

The following diagnosis might be helpful if the original folding top cover needs to be replaced.

Condition/Concern
The replacement folding top cover is a different design than the original top installed in production. The new design
folding top cover contains six control cords (three each side) which were not part of the original design cover. Holes
will need to be drilled into each side of the folding top frame to accept the rivets that will retain these cords.
The instructions below are steps for removal of the top assembly from the vehicle, removal of the top cover, drilling
the additional holes and installation of the new top cover including routing of the color keyed control cords.
Important: The three cords added to each side of the top cover are color-keyed with paint dots on the cord eyelets
only. The white, yellow and orange colors were added to the graphics below to represent the color-key of the eyelets.
The headliner cord was shown in red for illustration purposes only; the end eyelet of the headliner cord DOES NOT
have a color-key designation.

Inboard/Left Side View of Cord Routing and P-Clip, Eyelet and Straps Orientation

2884720

Outboard/Left Side View of Cord Routing and P-Clip, Eyelet and Straps Orientation

2874340

Note: The graphics above are views with the top in mid-open position and the right side views would mirror the left.
The top frame links and strap callouts referenced later in the instructions are noted in the key below.

Key to Call-outs Noted Above
–
–
–
–
–
–

(1) #2 Bow
(2) Control Link
(3) Rear #1 Bow Link
(4) Balance Link
(5) Headliner Strap
(6) Rear Top Cover Strap

Recommendation/Instructions
Recommendations
•
•
•
•

Read these instructions from beginning to end, including a review of any kit supplied instructions/appendices,
before starting the retrofit.
All the steps in this instructions are documented on the drivers side of the vehicle, unless noted otherwise.
When adding holes to the frame or riveting the cords/straps of the new top cover in place, complete each step
on both sides of the top before moving on to the next step.
For the additional holes drilled in the frame during the retrofit, drill bit size is critical for proper retention of the
rivets. A 13/64” bit should be used for the 5 mm (0.197 in) holes and a 1/8” bit should be used for the 3.2 mm
(0.125 in) holes.

Instructions
1. Remove the convertible top assembly from the vehicle. Refer to Folding Top Frame Replacement in SI.

2874341

2. Place the convertible top on a clean tarp or other clean, dry, suitable surface with the top cover facing
downward as shown above.
Note: When drilling out any existing rivets on the top cover or headliner, use a punch to mark a spot for drilling, at
the top center of the old rivet.
3. Start removal of the old top cover at the #1 bow, looking at the inside of the top. Remove the front edge retainer,
rail guides, top handle pocket garnish, flipper doors, and loosen the headliner as necessary. Refer to Folding
Top Cover Replacement in SI.
Important: Removing the #5 bow assembly IS NOT necessary for the top cover retrofit. The #5 bow assembly and
water management bag should stay attached to the folding top frame during the entire retrofit.
Note: The headliner should remain attached to the #3 bow, and all rearward bows, during this top cover
replacement procedure.
4. Release the headliner retaining bead around the rear window, remove the rear window pivot bracket nuts, and
disconnect the defogger connectors. Refer to Folding Top Cover Replacement in SI.

2874342

5. Position the folding top on the floor, sitting upright in the mid-open position with the 1 bow supported by a
suitable support as shown above.

2874343

Note: The fore/aft control cords were removed on the new top cover design. During reassembly, attachment to the 1
bow does not occur as in the previous design.
6. Start removing the top cover from the #1 bow exposing the entire top side of the #1 bow casting. Remove the
large header garnish molding by accessing the fasteners from the top side of the #1 bow. Disassemble the
headliner from the #1 bow and disconnect the top cover for/aft control cords from the #1 bow. Drill out the top
cover side strap rivets attached to the rear #1 bow link and control links. Refer to Folding Top Cover
Replacement in SI.

2905470

7. Remove the left and right side tension cables from the top cover and the rear side rail weatherstrips following
the steps below. If additional detail is needed, refer to Folding Top Cover Side Tension Cable Replacement in SI.
7.1. Remove the left front side tension cable spring retaining screw from the #1 bow.
7.2. Feed the side tension cable and spring out of the top cover material.
7.3. Pull the top cover edge plastic retainer out of the channel on the left rear side weatherstrip rail. Start at the
bottom and work your way upward.
7.4. Peel the left rear side weatherstrip out of the rail so there is access to the side tension cable.
7.5. Remove the piece of tape holding the tension cable end into the side rail link hole.
7.6. Remove the side tension cable anchor from the rear side rail.
7.7. Pull the cable back through the weatherstrip so it is free and clear of everything.
7.8. Repeat the same operation on the opposite side.

2874345

Note: Due to top cover replacement, the fabric connecting the top cover beads to the cover can be cut for quicker
removal. DO NOT cut any of the headliner beads.
Important: Mark the #2 bow to show that the top cover bead is installed in the front slot and the headliner bead is
installed in the rear slot. Note that the beads alternate front and rear position on each bow going rearward.
8. Starting at the #2 bow working rearward, remove the top cover from the bows by cutting the fabric connecting
the top cover retaining beads to the cover. After cutting the fabric, slide the beads out of the bows.

2874347

9. Remove the 5 bow seal and release the top cover retainer from the 5 bow. The old top cover can now be lifted
away from the top frame.

Early Design #2 Bow Bracket

2874348

Current Design #2 Bow Bracket

2874349

Important: The #2 bow end brackets are made of plastic and will likely break/snap during removal. Two new
brackets are included with the top cover replacement kit. Regardless of breakage, all early design #2 bow brackets
should be replaced.
10. Remove the #2 bow from the top frame assembly following the steps below:
10.1. If still attached, slide the headliner retaining bead out of the #2 bow and drill out the rivet retaining the side
headliner straps to each side 2 bow bracket.
10.2. Drill out the rivets (1) that hold the #2 bow brackets to each end of the #2 bow (two rivets per side).
Note: Make sure to retain the thrust washers and bushings from disassembly of the #2 bow brackets and balance
links. However, if parts are lost, extras are included in the top cover replacement kit.
10.3. With the aid of an assistant, technicians should stand on each side of the car, simultaneously holding the
#2 bow with one hand and pulling outward on the #2 bow brackets with the other hand. Gradually
increase the pull force until the #2 bow bracket is disengaged from the #2 bow.
10.4. Set aside the #2 bow for holes to be added in step #12.

2874351

10.5. Remove the retaining clips holding the #2 bow brackets to the balance link pins, and work the brackets
out of the linkage on each side. Pull inboard at the top of the balance link to disengage the pin and leave it
disengaged until later in the retrofit procedure.
Important: For ALL additional holes drilled, drill bit size is critical for proper retention of the rivets. A 13/64” bit
should be used for the 5 mm (0.197 in) holes and a 1/8” bit should be used for the 3.2 mm (0.125 in) holes. All holes/
rivets will be 5 mm (0.197 in) in size except for the single hole added to the left and right balance link, which is
3.2 mm (0.125 in).

2874353

Important: The two holes added to the #2 bow should be centered on the bow and ARE NOT through holes. DO
NOT drill through to the topside of the #2 bow.
11. While the #2 bow is removed, drill two 5 mm (0.197 in) holes (1) in the underside of the #2 bow. Position the
holes 102 mm (4.0 in) from each end of the bow.

2874355

12. Centered on the left rear #1 bow link, drill a 5 mm (0.197 in) hole (1) into the link, positioned 35 mm (1.375 in) (3)
from the center of the link pivot (2). Repeat the same operation on the opposite side of the top.

2912885

Note: Older convertible tops may be missing the upper 3.2 mm diameter hole shown in the control link above. If the
hole is missing, add by drilling a new 5 mm (0.197 in) hole positioned 10 mm (.0.40 in) (3) from the bend radius (2).
Repeat the same operation on the opposite side of the top.

2874358

13. Re-drill the two existing 3.2 mm (0.125 in) holes (1) in the left control link to open the diameter up to 5 mm
(0.197 in). Repeat the same operation on the opposite side.

2874360

Important: The holes added to the each balance link are on the outboard side of the link and ARE NOT through
holes. DO NOT drill through to the inboard side of the balance link. The right side balance link is shown in the
graphic above.
14. Centered on the outboard side of the right balance link (1), drill a new 3.2 mm (0.125 in) hole, positioned 80 mm
(3.15 in) from the center of weld bead (2). Repeat the same operation on the opposite side.

2874361

Important: The graphic above shows the left #5 bow bracket with the strap and cords removed, and also the
orientation of the new hole (1) and existing hole (2) for illustration purposes only. The new hole may or may not be
present and needs to be checked once the old top cover is removed. If the new hole is missing, add the 5 mm
(0.197 in) hole to both the left and right #5 bow brackets.

2874362

15. Drill a 5 mm (0.197 in) hole into the left and right #5 bow brackets, positioned 30 mm (1.12 in) (1) from the hole
where the rear headliner strap and water management bag cord are attached. Also drill out the rivet retaining
the strap/cord for repositioning those to the new hole.

2913650

Important: The graphic above shows the headliner strap, which is attached to the 5 bow bracket AFTER the rivet
was removed. If the top being retrofitted does not have a new 5 bow bracket with the new hole, then using a hot
mandrel, or equivalent tool, burn a new hole (1) into the headliner strap. As shown above, locate the new hole 30 mm
(1.20 in) (2) from the current location, then cut the reworked headliner strap at call out #3.

2874363

16. Lay out the new corded top cover on a clean, protected surface.

2874365

Important: Trial fit the top cover retaining beads into their corresponding roof bows. If installation is extremely
difficult, it may be necessary to remove material from all of the beads, prior to their full installation. Use sand paper,
or equivalent, to remove material from the tops of the beads to reduce/eliminate interference.

2874366

17. Starting from the passenger side, position the top cover beads to the beveled edge at the end of each bow.
18. With aid of an assistant, alternately feed the beads into the slots on roof bows #3, #3.5 and #4. Continue to work
the beads across to the opposite side until the all the top cover beads are centered on the roof bows.

2874367

Note: As marked during the removal earlier, the headliner bead goes in the rear #2 bow slot (1) and the top cover
bead goes in the front #2 bow slot (2).

2874368

19. Slide the reworked #2 bow onto the headliner and new top cover beads at the same time as shown above.

2874369

20. Reassemble the #2 bow bracket bushings (1).
21. With the aid of an assistant, partially install the thrust washers and #2 bow brackets to the #2 bow, while
simultaneously angling the brackets into position on the linkage on each side.

2874370

22. Ensure the brackets are fully seated on the #2 bow and install only the outboard rivets on the left and right side
at this time.

2874371

23. Reinstall the balance link pins and retaining clips on each side.

2874373

24. Rivet the new top cover #5 bow bracket cord to the new holes on the left and right #5 bow brackets, along with
the water bag cord and the headliner control strap as shown above.
25. Install the rear window pivot bracket nuts, connect the defogger connectors, reinstall the headliner bead around
the rear window, and secure the top cover to the #5 bow. Refer to Folding Top Cover Replacement in SI.
26. Reroute the side tension cables through the rear side rail, rear weatherstrip and top cover on each side following
the steps below. If additional detail is needed, refer to Folding Top Cover Side Tension Cable Replacement in SI.

2915759

Note: The design of the top cover plastic retainer has changed slightly on the new corded top covers. The plastic
retainer on the previous top covers had a slit near the end that allowed the side tension cable to pass through it as
shown above.
Instead of a slit in the plastic, the retainer now has a large square hole at the very end, which is large enough to allow
the cable anchor to pass through it. The retainer and square hole can be seen in the graphic below.

2915760

26.1. Starting on the left side, route the side tension cable through the backside of top cover edge plastic
retainer as shown above.
26.2. Next, route the cable through the small hole in the left side rail weatherstrip. It should run from the outside
of the weatherstrip to the inside so that the cable is hidden, and it runs alongside the metal side rail itself.
26.3. Attach the cable anchor point back into the side rail and secure it with a piece of tape to hold it in place.
26.4. Attach the forward side tension cable/spring end to a suitable wire, and starting at the bottom of the left
top cover pocket, pull the tension cable and spring upward/forward through the cover material until the
spring hangs from the exit slot at the front of the cover. The front spring retaining screw will be attached to
the #1 bow in a later step.
26.5. Install the left top cover plastic retainer into the channel in the metal side rail.
26.6. Press the left rear side rail weatherstrip back in place and make sure it is secure.

2900643

Note: The graphic above shows the correct routing of the side tension cable once everything is reinstalled.
26.7. Repeat the same operation on the opposite side.
27. Reinstall the top assembly to the vehicle. Refer to Folding Top Frame Replacement in SI.

2874374

28. Position the folding top in the mid-open position. Clear any contents out of the rear seat and move the front
seats forward. The technician will need to stand in the back seat to route and rivet the control cords and straps
to the top frame.

2884722

Note: The three cords added to each side of the top cover are color-keyed with paint dots on the cord eyelets. The
orientation of the three colors white (1), yellow (2) and orange (3), along with the rear (4) and front (5) control straps,
are shown above. The following steps will reference them as the white, yellow or orange control cords.
29. Rivet a new P-clip to the inboard hole of the #2 bow bracket on the left and right sides following the steps below:
Note: The headliner cord end eyelets will be riveted at a later step. They can hang off the top side of the P-clip
for now.

2874377

29.1. Route the cord (no color dot) coming off the headliner tab upward through the bottom of the P-clip.

2874379

29.2. Position the clip to the #2 bow so that the P-clip (1) is facing outboard as shown in the graphic above.
Note: The headliner control cord must be routed through the P-clip before installing the rivet.
29.3. Install the rivet. (The headliner cord end eyelets can hang off the top side of the P-clip for now. They will
be riveted to the control link later in step #32.)
29.4. Repeat the same operation on the opposite side.
Note: For the eye loop installations, use the more numerous flatter design eye loop except as noted in step #31.

30. Rivet a new eye loop to the remaining inboard-most hole on the left and right sides of the #2 bow following the
steps below:
30.1. Grab the 735 mm (29 in) yellow control cord, which is attached to a tab off the binding of the top cover.

2874382

30.2. Route the cord downward through the large eye loop (1) with the eye loop angled downward as shown
above.

2874384

30.3. Install the rivet on the #2 bow through the small eye loop hole with the large eye loop hole (1) aimed
outboard as shown above.
30.4. Repeat the same operation on the opposite side.
Note: The steps in the next several sections will normally need to be performed with the aid of an assistant.
Important: The eye loops attached to the left and right rear #1 bow links are the only two that contain a 75° bend.
These unique bend eye loops are used in only these two locations.
31. Rivet a new 75° bend eye loop to the hole previously drilled in the left and right rear #1 bow link following the

steps below:

2920243

31.1. Holding the eye loop (1) with the 75° bend angled upward, route the yellow (2) and orange (3) top cover
control cords down through the large eye loop opening.

2920246

31.2. Grab the eyelet on the end of the white top cover control cord. Put the eyelet (1) on the new rivet, then
add the eye loop (2) through the small hole.

2920250

Note: The large eye loop should already have the yellow and orange control cords routed through it, prior to
attaching the rivet.
31.3. Install the rivet to the rear #1 bow link with the 75° bend of the large eye loop angled inboard (as shown in
the inset above) and the orientation of the eye loop (1) and the cord eyelet (2) as shown.
31.4. Repeat the same operation on the opposite side.
32. Rivet the end eyelets of the headliner cord (no color dot), along with a new P-clip, to the forward hole previously

drilled in the left and right control links following the steps below:

2874390

32.1. Grab a new P-clip (1) and route the yellow and orange control cords through the P-clip as shown above.

2874391

32.2. Insert a new rivet in the headliner eyelet, then through the P-clip (with the yellow and orange cords
already running through it) and position them to the forward hole previously drilled in the control links.
32.3. Install the rivet to the control link with the orientation of the cord eyelet (1) and the P-clip (2) as shown
above.
32.4. Repeat the same operation on the opposite side.
33. Rivet a new eyelet, along with the rear strap that is attached to the top cover binding, to the rearward hole

previously drilled in the left and right control links following the steps below:

2874392

33.1. Route the yellow and orange control cords down through the large hole in a new eye loop (1) with the eye
loop angled upward as shown above.

2915762

33.2. Grab the rear top cover strap as shown above.

2915765

Important: Verify that the rear strap (1) of the top cover is routed under the side link and is not hung up behind, but
is clear of, the wishbone link (2) as shown above.

2915764

33.3. Insert a new rivet through the small eye loop (1), then through the strap (2) as shown above.

2915766

Note: The large eye loop should already have the yellow and orange control cords routed through it prior to
attaching the rivet. Also ensure that the cover strap is oriented straight down and under the link and not angled
forward or rearward.
33.4. Install the rivet to the control link with the orientation of the rear top cover strap (1) and the eyelet (2) as
shown above.
33.5. Repeat the same operation on the opposite side.

2874398

34. Rivet both end eyelets of the yellow and orange control cords to the hole previously drilled in the left and right
balance links following the steps below:
34.1. Insert a new 3.2 mm (0.125 in) rivet through the end eyelets on first the yellow (1), and then the orange
(2), control cords.
34.2. Attach the rivet to the hole in the balance link as shown above.
34.3. Repeat the same operation on the opposite side.

2884727

35. Balance the new cross-car control cord in the top cover’s second pocket by completing the following steps:
35.1. Cycle the top to the half open position.
35.2. Locate the second pocket control cord with the orange paint dot on the eyelet (2), which is the longer of
the two cords riveted to the balance link.
35.3. With your index finger, pull the cord forward, taking out the slack.
35.4. When the cords are even from side to side, there will be a gap of about 25 mm (1.0 in) (1) between your
finger and the balance link as shown above. If the gap is less than an inch, reach into the top cover and
gently pull the cord towards you, then recheck the gap. Noting the gap on one side, go to the other side of
the top and repeat the process. Repeat this process from side to side until the gaps are equal.
36. Complete the installation of the top cover at the #1 bow. Reinstall all tension cables, trim, and forward headliner
straps removed previously. Refer to Folding Top Cover Replacement in SI.
37. After balancing the cross car cord and completing the top cover installation, cycle the top to the fully stowed
position before cycling the top closed.
38. Verify proper operation of the folding top.

Warranty Information
For vehicles repaired under warranty, use:
Labor Operation

Description

Labor Time

B6823*

Retrofit Replacement of New Corded Top Cover to Original Design
Frame

7.0 hrs

Add

For vehicles equipped with 6 tube drain panel system

0.4 hr

*This is a unique labor operation for bulletin use only. It will not be published in the Labor Time Guide.