Technical Bulletin
Model(s)

Year

Eng. Code

Trans. Code

VIN Range From

VIN Range To

Jetta

2005 – 2010

All

All

All

All

Condition
55 14 04 December 4, 2014 2038992
Corrosion on the Rear Lid around License Plate Lights

Figure 1: Corrosion on and around the license plate light
Note:
To determine if this procedure is covered under Warranty, always refer to the Warranty Policies and Procedures
Manual.
Documentation required per Warranty Policies and Procedures Manual.
For vehicles outside of the Limited Warranty Against Corrosion Perforation this Technical Bulletin is for information
only.

Technical Background
Electrolytic corrosion around the license plate lights (opening/contact surface, inside and outside) because of
water ingress via the seal of the license plate lights.

© 2014 Volkswagen Group of America, Inc.

Page 1 of 7 plus attachments

All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Technical Bulletin
Production Solution
Not applicable.

Service
Procedure:
1a. Repair (Remove corrosion and restore paint structure).
Only perform this operation if the total repair cost is 80% or less of the total replacement cost.
Or
1b. Replace the rear lid.

Note:
Steps 2-3 should be completed whether the rear lid is repaired or replaced.
2. Seal off contact surface and screw holes of license plate lights with butyl sealing cord (part number:
AKL 450 005 05).
3. Replacement of license plate lights.
1a. Repair (Remove corrosion and restore paint structure)
• Remove the license plate lights from the rear lid according to the repair manual. See Repair Group 94 in Elsa.
• Remove all trim panels from the rear lid to prepare for corrosion removal according to the repair manual. See
Repair Group 70 in Elsa.
• Remove the corrosion on the rear lid contact surface around the license plate light (inside and outside) with a
pneumatic brush grinder.
Note:
If through-corrosion (perforation) is not present, rear lid replacement will only be accepted if it qualifies per the
Reimbursement Policy section of the Warranty Policies and Procedure Manual. This section provides important
guidelines when considering component repair vs. replacement options (the “80% rule”).
• Prepare the rear lid for painting according to manufactures guidelines - it is not necessary to remove the glass.
• Apply a VOC compliant epoxy primer as an anti-corrosion treatment and primer (locally sourced).
• Repaint the rear lid according to manufactures guidelines.

© 2014 Volkswagen Group of America, Inc.

Page 2 of 7 plus attachments

All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Technical Bulletin
1b. Replace the rear lid
• Replace the rear lid according to the repair manual. See Repair Group 55 in Elsa.
2. Additionally seal the contact surface of the license plate lights with butyl sealing cord (part number:
AKL 450 005 05).
• Apply butyl sealing cord (0.2 cm x 20 cm) on the contact surface and attachment area of the license plate lights
(Figure 2 and 3 in green).

Figure 2) License plate light, butyl sealing cord areas

Figure 3) License plate light, contact surface and hole sealed with butyl sealing cord

© 2014 Volkswagen Group of America, Inc.

Page 3 of 7 plus attachments

All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Technical Bulletin
3. Replacement of the license plate lights
• Install the new license plate lights in the rear lid according to the repair manual. See Repair Group 94 in Elsa.
• Remove any excess butyl sealing cord.
• Install all trim panels for the rear lid according to the repair manual. See Repair Group 70 in Elsa.

Warranty
Note:
• Dealers may complete the repair as described without prior authorization (through a WISE Warranty Repair
Acceptance request).
• Documentation required: Clear pictures, completed estimate and body shop invoice must be saved and kept on
file at the Dealership for audit purposes.
• Labor time units (TU), Material units (MU), and Material unit rate are correct at the time of publication. The time
units and/or material units may differ if the repair catalogue is updated. The information in the repair catalogue
applies, except for the open time items (labor operations ending in 99) which are calculated at actual time
multiplied by the body shop labor rate. The material allowance (Paint material price per unit) is subject to
change. Refer to WISE > Resource Center > Forms > Paint/Corrosion for the most current forms.
• This section is applicable for vehicles within the terms of Volkswagen’s Limited Warranty Against Corrosion
Perforation. For vehicles outside the terms of the Limited Warranty Against Corrosion Perforation this section is
for information only.
• This bulletin may be provided to outside shops to ensure the proper repair is completed.
Note:
Claim Processing Options
Option 1: Utilize the attached form examples and interactive forms on WISE to assist with calculating the
reimbursement amounts. This will expedite the claim review process and reduce the time to pay the claim.
Note that miscalculations are subject to claim adjustment.
For the complete set of pre-populated Paint/Corrosion Claim Form templates associated with this Technical
Bulletin, refer to WISE > Resource Center > Forms > Paint/Corrosion.
Option 2: Email repair estimates to paintcamp@vw.com. The Paint and Corrosion Team will calculate the
warranty allowance and complete the required form(s) on behalf of the dealer.
To determine if this procedure is covered under Warranty, always refer to the Warranty Policies and
1)
Procedures Manual
Model(s)

Year(s)

Eng. Code(s)

Trans. Code(s)

VIN Range From

VIN Range To

Jetta

2005-2010

All

All

All

All

SAGA Coding
© 2014 Volkswagen Group of America, Inc.

Page 4 of 7 plus attachments

All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Technical Bulletin
1)

Claim Type:

160

Damage

Service Number:

Code

5559

0003

Parts Manufacturer

HST

Damage Location
(Depends on Service No.)

--

030

Jetta (1K2)

030

2)

Repair
Please use the following part number in “Outside Materials”

4)

LACKMATF: Paint and Materials

MU @ $12 per unit

Epoxy Primer (Locally Sourced)

Claim Dollar Amount (MAX: $40)

Please use the following Labor Operation in “Outside Labor”

4)

Select the appropriate Labor Operation below:
- L0010000: External Painting-straight color
- L0020000: External Painting-metallic/2-layer

Claim Dollar Amount

- L0030000: External Painting-pearl color
Use this for all body repair in this bulletin:
- A0041000: Body Shop repair no paint

Claim Dollar Amount
Replace

Please use the following part number in “Outside Materials”
LACKMATF: Paint and Materials

4)

MU @ $12 per unit

Please use the following Labor Operation in “Outside Labor”

4)

Select the appropriate Labor Operation below:
- L0010000: External Painting-straight color
- L0020000: External Painting-metallic/2-layer

Claim Dollar Amount

- L0030000: External Painting-pearl color
Use this for all body repair in this bulletin:
- A0041000: Body Shop repair no paint
© 2014 Volkswagen Group of America, Inc.

Claim Dollar Amount

Page 5 of 7 plus attachments

All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Technical Bulletin
Causal Part:

L00#0000
Diagnostic Time

4)

GFF Time expenditure

01500000 = 00 TU max.

NO

Road Test

01210002 = 00 TU

NO

01210004 = 00 TU
Technical Diagnosis

01320000 = 00 TU

NO

Claim Comment: Input “As per Technical Bulletin 2038992” in comment section of Warranty Claim.
1)

For Vehicles outside the Limited Warranty Against Corrosion Perforation this bulletin is information only

2)

Corrosion claim vendor code will be the damage location.

3)

Labor Time Units (TUs) are subject to change with ELSA updates.

4)

Documentation required per Warranty Policies and Procedures Manual.

5)

See attachment “srt_ref_table.pdf” for labor time reference.

Required Parts and Tools
Replace
Part number

Designation

1K5 827 025 AD/AP

Rear Trunk
Repair and Replace

AKL 450 005 05

Butyl sealing cord (Quantity 0.1)

6Q6 955 758 A

Seal

3B5 943 021 B/E

License Plate Lights

No Special Tools Required.

© 2014 Volkswagen Group of America, Inc.

Page 6 of 7 plus attachments

All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Technical Bulletin
Additional Information
All part and service references provided in this Technical Bulletin are subject to change and/or removal.
Always check with your Parts Dept. and Repair Manuals for the latest information.

© 2014 Volkswagen Group of America, Inc.

Page 7 of 7 plus attachments

All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Paint/Corrosion Claim Form

Dealer No.
Repair
Order No.

400000

VIN (17-Digits)

910000

Color No. (4-digit ElsaPro Paint No.)

3VWBA71K18M167634
LR9A
100.00

Dealer Labor Rate

If repeat repair, provide explanation in box below:

12.00

Paint material price per unit

Service No.

Damage
Code

Dmg
Loc

Part manufacturer
(Vendor Code)

5559

0003

030

030

Dealer-owned paint shop?

Yes

Original paint material?

Yes

Description of Repair

Paint trunk lid

Paint Labor Operation(s)

No
No
Time
Units

Mat'l
Units

55907953

130

51017173

160

9

Verify ALL Labor Operation Time Units
and Material Units

If both fenders are affected, the prep time
should be entered on the first line of the
SAGA claim and only once on the first
Paint/Corrosion Claim Form

Note: Authorization and claim reimbursement are contingent on the usage of original
parts for the repair

Body Painting Prep Time

The vehicle history must be checked for any previous damage. Digital photographs must be included with the repair order per VWoA instructions. If there is a
sublet invoice for painting, the invoice amount must be split between outside (sublet) labor and outside (sublet) material.

Part Number

Part Description

EPOXY

Part Qty

Epoxy Primer

Part Price
per Unit