Technical Service Bulletin
37 Transmission warning message in cluster (DTC P060A00)
37 14 47 2029027/11 September 26, 2014. Supersedes Technical Service Bulletin Group 37 number 14-42 dated
August 1, 2014 for reasons listed below.
Model(s)

Year

VIN Range

Vehicle-Specific Equipment

A4,A5, A5
Cabriolet

2011 - 2013

All

8 speed 0BK Transmission

Q5

2011 - 2013

All

8 speed 0BK Transmission, 2.0T

A6, A7

2013

All

8 speed 0BK Transmission

A8

2011 - 2013

All

8 speed 0BK Transmission

Condition
REVISION HISTORY
Revision

Date

Purpose

11

-

Revised header data (Added Model Year 2011 A4, A5, A5 Cabriolet, and Q5)
Revised Condition (Removed Tip)

10

8/1/2014

Revised header data (Removed Model Year 2011 A4, A5, A5 Cabriolet, and
Q5)
Revised Condition (Added Tip)

9

5/22/2014

Revised Service (Updated SVM table, New SVM code and software levels)

8

9/11/2013

Revised Warranty (Updated Diagnostic Time to cover 2013 road test after
procedure)

7

4/26/2013

Revised Service (Updated SVM table, ECM update added for A8 4.0T and S8)
Revised Warranty (reflected changes in Service section)

6

4/1/2013

Revised Service (Updated SVM table)

5

12/19/2012

Revised Service (Updated SVM table)

• Customer may report transmission warning light is illuminated. In some cases, the vehicle will not move after
being started and placed into gear. After key cycle, the vehicle drives without restriction.
• One of the following DTCs is stored in the transmission control module (TCM), J217 (02):
• DTC P060A00 (Internal Control Module Monitoring Processor Performance) with DFCC 8692
• DTC P060A00 (Internal Control Module Monitoring Processor Performance) with DFCC 8694

© 2014 Audi of America, Inc.

Page 1 of 5

All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior
expressed written permission of the publisher.

Technical Service Bulletin
• DTC P060A00 (Internal Control Module Monitoring Processor Performance) with DFCC 12480
Tip: If DFCCs do not match exactly, this TSB does not apply.

Technical Background
The DTCs are stored due to an issue with the transmission control module software. Specific DFCCs are stored
as a result of the following situations:
• DTC P060A00 with DFCC 8692 can be logged when a driving mode (Drive or Reverse) is selected within one
second of selecting Neutral, while the vehicle rolls at a speed less than 2 mph (such as when the vehicle is
being maneuvered in or out of a parking spot).
• DTC P060A00 with DFCC 8694 can be logged when the gear is quickly changed from Park to Neutral, due to a
low diagnosis threshold.
• DTC P060A00 with DFCC 12480 can be logged when the gear is changed using the Tiptronic function, due to
a low diagnosis threshold.

Production Solution
• New software in the Transmission Control Module (TCM), J217 (02), addressed the condition.
• For the A8 4.0T and S8 models, there is new software in Engine Control Module (ECM), J623 (01) that should
be used in combination with new software in the Transmission Control Module, J217 (02), which addresses the
condition.

Service
1. Ensure that the DFCCs match exactly before
proceeding. The DFCC is the 4-6 digit code in front
of the P code, as pictured (Figure 1).

Figure 1. Locating the 4-6 digit DFCC code.
© 2014 Audi of America, Inc.

Page 2 of 5

All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior
expressed written permission of the publisher.

Technical Service Bulletin
2. Update the software using the SVM Update Instructions below.

SVM Update Instructions
1. Follow all instructions in the attached TSB, 2011732 00 Software Version Management (SVM), operating
instructions.
2. Update the TCM using the SVM action code as listed in the table below if necessary.
3. For A8 4.0T and S8 vehicles, update the ECM and the TCM, if necessary. The update may have already been
performed in TSB 2033726.

Model

Engine and/or
Transmission

Old Software Part
Number

Old
Software
Version

New Software Part New
Number
Software
Version

SVM Code
Input

(or higher)
Transmission Software Update (except A8 4.0T and S8)
A4, A5, A5
Cabriolet

2.0L with 8
speed
Transmission

A4, A5, A5
Cabriolet

2.0L with 8
speed
Transmission

Q5

2.0L with 8
speed
Transmission

Q5

2.0L with 8
speed
Transmission

A6, A7
A8, A8L

A8, A8L

3.0L with 8
speed
transmission

4.2L with 8
speed
transmission

6.3 W12 with 8
speed
© 2014 Audi of America, Inc.

8K0927158K