Technical Service Bulletin
01 MIL on, DTC for "System rich" (P1137 and/or P1139)
01 12 58 2031458/1 November 5, 2012.
Model(s)

Year

VIN Range

S4, S5

2010-2012

All

A6

2012

All

A7

2012

All

A6 (C6)

2009-2011

All

Q7

2011-2012

All

Vehicle-Specific Equipment

3.0 TFSI engine

Condition
MIL on, with one or more of following DTCs stored in the 01 (Engine Control Module):
 P113700 (System rich, Bank 1)
 P113900 (System rich, Bank 2)

Technical Background
Under extreme driving conditions, such as a driving profile of mainly short distance (stop and go) driving high
crankcase pressure can lead to the above described DTC codes. By changing the crankcase pressure valve to a
lower operating pressure this condition can be improved and eliminate the mentioned possible DTC codes. Along
with the crankcase pressure being lowered, a new ECM software level is required to compensate for new
crankcase pressure.

Production Solution
Crankcase pressure reduction starting with model year 2013.

Service

Page 1 of 4 plus attachment
© 2012 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted
in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.

Technical Service Bulletin
1. Replace crankcase pressure regulating valve using Repair Manual instruction provided in
Elsa Web (Engine >> Engine Mechanical >> 17 Lubrication >> Removal and Installation

>> Cover with Oil Separator) with part number 06E103547H.
Tip: Reuse collected oil.
2. Follow all instructions in the attached TSB 2011732 00 Software Version Management

(SVM), operating instructions.
3. Update the 01 (Engine Control Module) using SVM action code as listed in the table below
if necessary.

Model

Engine

Old Software

Old Software

New Software

New

SVM Action

Part Number

Version

Part Number

Software

Code

Version
2009 – 2011
A6

CCAA

4F1910551A

All

8K0907551

All

4F1910551D

0050

8K0907551D

0003

S4, S5
Cabriolet

CCBA

2010 – 2012
2012 A6 / A7

2011 –
2012 Audi Q7

A&B

01A092

CGXB

4G0907551A

All

4G0907551A

0007

CJWB

4L0910551K

0010

4L0910551K

0040

CJWC

4L0910551A

0010

4L0910551A

0050

CJWE

4L0910551J

0010

4L0910551J

0040

Warranty

Page 2 of 4 plus attachment
© 2012 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted
in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.

Technical Service Bulletin
Claim Type:

Use applicable claim type. If vehicle is outside any warranty, this Technical
Service Bulletin is informational only.

Service Number:

1050

Damage Code:

0010

Labor Operations:

Audi Q7:
Pressure regulating
valve remove + install

1050 9999

80 TU

Fuel Rail remove + install 2441 2089

70 TU

(reduced for overlap)

Compressor remove +

2114 1939

160 TU

1050 1941

370 TU

1050 1999

50 TU

Fuel Rail remove + install 2441 2091

70 TU

Compressor remove +

2114 1941

160 TU

0150 0000

20 TU

install
S4/S5/S5 Cab:
Pressure regulating
valve remove + install
A6/A7:
Pressure regulating
valve remove + install
(reduced for overlap)

install
Diagnostic Time:

GFF

Road test prior to service No allowance

0 TU

procedure
Road test after service

0121 00 04

10 TU

procedure

Page 3 of 4 plus attachment
© 2012 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted
in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.

Technical Service Bulletin
Technical diagnosis at dealer’s discretion
(Refer to Section 2.2.1.2 and Audi Warranty Online for DADP allowance details)
Claim Comment:

As per TSB #2031458/1

All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures

Manual. Claims are subject to review or audit by Audi Warranty.

Required Parts and Tools
Parts Number

Part Description

Quantity

06E103213

Vent Tube

1

06E103547H

Crankcase pressure regulating valve

1

06E998907D

Repair kit

3

N 90316802

O-Ring Seal

1

079129717B

Seal

3

079129717D

Seal

6

G 012A8G1G

Coolant for top off

0.3 quarts

Additional Information
The following Technical Service Bulletin will be necessary to complete this procedure:
 TSB 2011732 00 Software Version Management (SVM), operating instructions.

All parts and service references provided in this TSB are subject to change and/or removal. Always check with
your Parts Department and service manuals for the latest information.

Page 4 of 4 plus attachment
© 2012 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted
in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.

Technical Service Bulletin
00 Software Version Management (SVM), operating instructions
00 12 32 2011732/9 February 7, 2012. Supersedes Technical Service Bulletin Group 00 number 10 – 02 dated
March 24, 2010 for reasons listed below.
Model(s)

Year

VIN Range

Vehicle-Specific Equipment

All Audi

2002 on

Not Applicable

Not Applicable

Condition
REVISION HISTORY
Revision

Date

Purpose

9

-

Revised header data (Added model years)
Revised Technical Background
Revised Service (Added image)

8

3/24/2010

Revised Technical Background
Revised Service (Added Response Codes section)

7

5/13/2009

Revised Service (Step 6)

6

12/15/2008

Revised Service (Step 3 – added information concerning use of wireless
VAS 5054A transmitter head)

5

11/17/2008

Revised Title to include Repair Group

4

10/21/2008

Revised Service (Step 3 – added information concerning Windows power
savings settings)

This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management
(SVM) software update for any TSB or Update.
Troubleshooting information is included in the Additional Information section.
Please refer to the upcoming TSBs covering detailed aspects of SVM. They will be listed under group “99”.

Technical Background
SVM was developed with the main goal of ensuring each Audi vehicle has the correct electronic control units with
the correct software versions installed when it leaves the dealership repair facility.

© 2012 Audi of America, Inc.

Page 1 of 10

All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior
expressed written permission of the publisher.

Technical Service Bulletin
SVM is a feature of GFF that has a subset of
functions or components as seen in Figure 1. These
functions are explained below. A VAS 5051B, VAS
5052A, or VAS 6150(A/B/C) diagnostic tool is
required to read out the vehicle control unit data and
send it to the SVM server (also called an “SVM
communication”).