TECHNICAL BULLETIN
UPS7212-1bNAS1
20-DEC-12
THIS UPDATE PRIOR TO SALE NOTICE IS VALID FOR A LIMITED TIME ONLY AND
WILL EXPIRE ON 30 JUNE 2013
SECTION: 307-07

Update Prior to Sale: ‘2WD only traction reduced’ Message Displayed
on Start Up
AFFECTED VEHICLE RANGE:
XJ (X351) All-Wheel Drive only

VIN:
Model Year:

V42261-V44710 (specific VINs only; see
attached list)
2013

CONDITION SUMMARY:
Situation: A potential concern has been identified on XJ All-Wheel Drive vehicles where a ‘2WD only traction
reduced’ message may be displayed on vehicle start up. The message will clear on the next ignition cycle.
Action: Retailers are required to before sale HOLD all affected vehicles in the above VIN range that are in
their control and refrain from releasing the vehicles for new or used vehicle sale pending completion of the
rework action detailed in this Technical Bulletin. For vehicles in retailer inventory, this should be done at the
completion of the Pre-Delivery Inspection (PDI) process.

PARTS:
No parts necessary

TOOLS:
IDS with latest IDS-DVD and Calibration File; first available on IDS-DVD132.02 v.122
Jaguar-approved Midtronics Vehicle Power Supply

WARRANTY:
NOTE: Repair procedures are under constant review, and therefore times / prices are subject to change;
those quoted here must be taken as guidance only. Always refer to DDW to obtain the latest repair time.
Check DDW to ensure that the vehicle is affected by this program prior to undertaking any rework action. At
the time of confirming a booking for vehicle repair, ensure that all outstanding Service Actions are identified to
ensure the correct parts are available and adequate workshop time is allocated for repairs to be completed at
one visit.
Warranty claims must be submitted quoting Program Code 'K163' together with the relevant Option Code from
the table. The SRO and part information listed have been included for information only. The Option Code(s)
that allows for the drive in / drive out allowance can only be claimed if the vehicle is brought back into the
workshop for this action alone to be undertaken.
This program is valid for a limited time only. Warranty claims with a repair date prior to the 30 June 2013
closure date must be submitted for payment within 30 calendar days of completion of the repair.
PROGRAM
CODE

OPTION
CODE

DESCRIPTION

K163

B

Update transfer case control module
software

86.98.02

0.20

-

-

0.20

-

-

C

Update transfer case control module
software
Drive in / drive out

86.98.02

K163

10.10.10

0.10

-

-

SRO

PART NO.

TIME
(HOURS)

QTY. /
VALUE

Normal Warranty policies and procedures apply
NOTE: The information in Technical Bulletins is intended for use by trained, professional Technicians with the knowledge, tools, and
equipment required to do the job properly and safely. It informs these Technicians of conditions that may occur on some vehicles, or
provides information that could assist in proper vehicle service. The procedures should not be performed by 'do-it-yourselfers'. If you are not
a Retailer, do not assume that a condition described affects your vehicle. Contact an authorized Jaguar service facility to determine whether
this bulletin applies to a specific vehicle.
© Jaguar Land Rover North America, LLC 555 MacArthur Boulevard

Mahwah, NJ 07430

REPAIR PROCEDURE
CAUTION: Ensure all ignition 'ON' / ignition 'OFF' requests are carried out; failure to perform these
steps may cause damage to control modules in the vehicle.
CAUTION: A Jaguar-approved Midtronics Vehicle Power Supply must be connected to the vehicle
battery during IDS diagnosis / module programming.
1. Connect the Jaguar-approved Midtronics Vehicle Power Supply to the vehicle battery.
2. Turn ignition 'ON' (engine not running).
3.
4.
5.
6.
7.
8.
9.

NOTE: IDS must be loaded with IDS-DVD133.02 v.122 or later.
Connect the IDS to the vehicle and begin a new Symptom Driven Diagnostics (SDD) session.
Follow the on-screen prompts, allowing SDD to read the VIN and identify the vehicle.
From the Session Type selection screen, choose 'Campaigns'.
From the Recommendations tab, select 'Run' to perform the ‘Configure existing module - Transfer case
control module' option.
Follow all on-screen instructions to complete this task.
Exit the current session.
Disconnect the IDS and the Midtronics Vehicle Power Supply from the vehicle.

UPS7212 AFFECTED VIN LIST

CANADA
RETAILER CODE / NAME

VIN

4202 Jaguar Vancouver

V44620

4202 Jaguar Vancouver

V44710

4497 Jaguar Richmond

V42261

4501 Jaguar Victoria

V44613

4501 Jaguar Victoria

V44641

4506 Jaguar Edmonton

V44629

4506 Jaguar Edmonton

V44671

4508 Jaguar Kelowna

V44633

4508 Jaguar Kelowna

V44635

USA
RETAILER CODE / NAME

VIN

1049 Jaguar Jacksonville

V44034

5381 Jaguar Albany

V43955

5387 Jaguar Orlando

V44085

5390 Jaguar Austin

V43959

5398 Jaguar Greensboro

V44090

5446 Jaguar Winston Salem

V44129

5498 Jaguar Woburn

V44125

5498 Jaguar Woburn

V44177

5614 Hampton Jaguar

V44015

5670 White Plains Jaguar

V44217

5672 Autobahn Motorcars

V44078

5675 Jaguar Cleveland

V44065

5713 Jaguar of the Gulf Coast

V44040