Page 1 of 3

TECHNICAL BULLETIN
K202 UPS6813-2bNAS1
10 DEC 2013

© Jaguar Land Rover North America, LLC
NOTE: The information in Technical Bulletins is intended for use by trained, professional Technicians with the knowledge, tools,
and equipment required to do the job properly and safely. It informs these Technicians of conditions that may occur on some
vehicles, or provides information that could assist in proper vehicle service. The procedures should not be performed by 'do-ityourselfers'. If you are not a Retailer, do not assume that a condition described affects your vehicle. Contact an authorized
Jaguar service facility to determine whether this bulletin applies to a specific vehicle.

Changes are highlighted in gray

SECTION: 307-05 / -05C

Update Prior to Sale: Transmission Control Switch Fails to Rise
AFFECTED VEHICLE RANGE:
XF (X250)
Model Year:
VIN:

2013-2014
U06088-U15793

XJ Range (X351)
Model Year:
VIN:

2013-2014
V59424-V63557

XK Range (X150)
Model Year:
VIN:

2013-2014
B53037-B54012

MARKETS:
NAS

CONDITION SUMMARY:
Situation: The Transmission Control Switch (TCS) may fail to rise when the engine Start/Stop button is pressed
(ignition switched 'ON'). Repeated cycling of the engine Start/Stop button may temporarily overcome this issue.
Action: Retailers are required to HOLD all affected vehicles within the listed VIN range that are in their control
and refrain from releasing the vehicles for new or used vehicle sale pending completion of the rework action
detailed in this Technical Bulletin. Unsold vehicles should have this performed as part of the Pre-Delivery
Inspection (PDI) process. Affected vehicles already in the hands of customers should be updated at the next
available opportunity.

PARTS:
No parts required

SPECIAL TOOLS:

NOTE: This document is an 'Active Bulletin' that will display a functional programming shortcut if
accessed within a diagnostic session using SDD.
SDD with latest SDD-DVD and Calibration File; first available on DVD136.03 v.158
Jaguar Land Rover-approved Midtronics Battery Power Supply

http://topix.jaguar.jlrint.com/topix/service/procedure/448815/ODYSSEY_FSA/G171585...

12/11/2013

Page 2 of 3

WARRANTY:

NOTE: Check DDW to ensure that the vehicle is affected by this program prior to undertaking any
rework action. Repair procedures are under constant review, and therefore times / prices are subject to
change; those quoted here must be taken as guidance only. Refer to the Repair Times Searcher (RTS) on
TOPIx to obtain the latest repair time. At the time of confirming a booking for vehicle repair, ensure that
all outstanding Service Actions are identified to ensure the correct parts are available and adequate
workshop time is allocated for repairs to be completed at one visit.
Warranty claims must be submitted quoting Program Code 'K202' together with the relevant Option Code from the
table. The SRO and part information listed have been included for information only. The Option Code(s) that allows
for the drive in / drive out allowance can only be claimed if the vehicle is brought into the workshop for this action
alone to be undertaken.
This program is valid for a limited time only. Warranty claims with a repair date prior to the 19 May 2014 closure
date must be submitted for payment within 30 calendar days of completion of the repair.
PROGRAM
CODE

OPTION
CODE

DESCRIPTION

SRO

TIME
(HOURS)

PARTS

QTY. /
VALUE

K202

B

Update Transmission Control Switch 86.99.91 0.20
software

-

-

K202

C

Update Transmission Control Switch 86.99.91 0.20
10.10.10 0.10
software
Drive in/drive out

-

-

NOTE: Normal Warranty policies and procedures apply

SERVICE INSTRUCTION:
1.

CAUTION: Ensure all ignition 'ON' / ignition 'OFF' requests are carried out; failure to perform
these steps may cause damage to control modules in the vehicle.

CAUTION: A Jaguar Land Rover-approved Midtronics battery power supply must be connected
to the vehicle battery during SDD diagnosis / module programming.

NOTE: SDD must be loaded with DVD136.03 v.158 or later.
Connect the Jaguar Land Rover-approved Midtronics battery power supply to the vehicle battery.

NOTE: The Transmission Control Switch may also be referred to as Gearshift Module.

2. Turn ignition 'ON' (engine not running).

3. Connect the Symptom Driven Diagnostics (SDD) system to the vehicle and begin a new session.

4. Follow the on-screen prompts, allowing SDD to read the VIN and identify the vehicle and initiating the data
collect sequence.

http://topix.jaguar.jlrint.com/topix/service/procedure/448815/ODYSSEY_FSA/G171585...

12/11/2013

Page 3 of 3

5. Select 'Diagnosis' from the Session Type screen.

6. Select the 'Selected Symptoms' tab, and then select the following:
Powertrain - Automatic transmission and transaxle - Automatic transmission and transaxle symptoms

7. Select the 'Extras' tab.

8. From the Recommendations tab, select Run to perform the 'Configure existing module – Gearshift module'
option.

9. Follow all on-screen instructions to complete this task.

10. Exit the current session.

11. Disconnect the SDD and the battery power supply from the vehicle.

http://topix.jaguar.jlrint.com/topix/service/procedure/448815/ODYSSEY_FSA/G171585...

12/11/2013