Page 1 of 2

TECHNICAL BULLETIN
JTB00317NAS2
02 DEC 2013
© Jaguar Land Rover North America, LLC
NOTE: The information in Technical Bulletins is intended for use by trained, professional Technicians with the knowledge, tools,
and equipment required to do the job properly and safely. It informs these Technicians of conditions that may occur on some
vehicles, or provides information that could assist in proper vehicle service. The procedures should not be performed by 'do-ityourselfers'. If you are not a Retailer, do not assume that a condition described affects your vehicle. Contact an authorized
Jaguar service facility to determine whether this bulletin applies to a specific vehicle.

This reissue replaces all previous versions. Please destroy all previous versions. Only refer to the
electronic version of this Technical Bulletin in TOPIx.
Changes are highlighted in gray

SECTION: 204-04

Tire Pressure Monitoring System Control Module Reset Issue
AFFECTED VEHICLE RANGE:
XF (X250)
Model Year:
VIN:

2009-2012
R00019-S39426

XK Range (X150)
Model Year:
2007-2012
VIN:
B00379-B47482

MARKETS:
NAS

CONDITION SUMMARY:
Situation: The Tire Pressure Monitoring System (TPMS) may intermittently display a low pressure warning in the
Instrument Cluster (IC). Upon checking the vehicle's tire pressures, all are found to be within specification with
no low pressures found. Additionally, there are no TPMS Diagnostic Trouble Codes (DTC) stored as there are no
faults within the TPMS.
Cause: This may be caused by a software issue in the Tire Pressure Monitoring System Control Module
(TPMSCM).
Action: Should a customer express this concern, follow the Service Instruction outlined below.

PARTS:
No Parts Required

TOOLS:

NOTE: This document is an 'Active Bulletin' that will display a functional programming shortcut if
accessed within a diagnostic session using SDD.

SDD with latest DVD and Calibration File; first available on DVD134.06 v.138
Jaguar Land Rover-approved Midtronics battery power supply

WARRANTY:
NOTE: Repair procedures are under constant review, and therefore times are subject to change;
those quoted here must be taken as guidance only. Always refer to TOPIx to obtain the latest repair
time.
NOTE: DDW requires the use of causal part numbers. Labor only claims must show the causal part

http://topix.jaguar.jlrint.com/topix/service/document/448042

12/10/2013

Page 2 of 2

number with a quantity of zero.
DESCRIPTION

SRO

TIME
(HOURS)

CONDITION
CODE

CAUSAL
PART

Update Tire Pressure Monitoring System Control
Module software

86.99.62

0.2

42

C2Z1523

NOTE: Normal Warranty policies and procedures apply.

SERVICE INSTRUCTION:
1.

NOTE: Prior to commencing the Service Instruction, make sure all tire pressures are within
specification and no Tire Pressure Monitoring System (TPMS) fault is evident.
Check the vehicle tire pressures.
If the tire pressures are within specification, the Tire Pressure Monitoring System (TPMS) is operating

correctly, and there are no TPMS Diagnostic Trouble Codes (DTC) stored, continue to step 2.
If the tire pressures are not within specification or there is a TPMS fault found, rectify as necessary. No

further action required.

2.

CAUTION: A Jaguar Land Rover-approved Midtronics battery power supply must be connected
to the vehicle battery during SDD diagnosis / module programming.

NOTE: SDD must be loaded with DVD134.06 v.138 or later.
Connect the Jaguar Land Rover-approved Midtronics battery power supply to the vehicle battery.
3. Turn ignition 'ON' (engine not running).
4. Connect the Symptom Driven Diagnostics (SDD) equipment to the vehicle and begin a new session.
5. Follow the on-screen prompts, allowing SDD to read the VIN and identify the vehicle and initiating the data
collect sequence.
6. Select 'Diagnosis' from the Session Type screen.
7. Select the 'Selected Symptoms' tab, and then select one the following:
Electrical > Instruments > Warning lamps > TPMS warning lamp illuminated > Lamp flashes at ignition-on

for 75 seconds then remains illuminated or
Electrical > Instruments > Status lamps > Tire pressure monitoring system lamp > Lamp flashes at

ignition-on for 75 seconds then remains illuminated or
Chassis > Wheels and tires > TPMS

8. Select 'continue'.
9. Select the 'Recommendations' tab, and then select 'Run' to perform the 'Configure existing module – Tire
pressure monitor module' option.
10. Follow all on-screen instructions to complete this task.
11. Exit the current session.
12. Disconnect the SDD and the battery power supply from the vehicle.

http://topix.jaguar.jlrint.com/topix/service/document/448042

12/10/2013