Page 1 of 6

TECHNICAL BULLETIN
JTB00286NAS1
05 NOV 2013
© Jaguar Land Rover North America, LLC
NOTE: The information in Technical Bulletins is intended for use by trained, professional Technicians with the knowledge, tools,
and equipment required to do the job properly and safely. It informs these Technicians of conditions that may occur on some
vehicles, or provides information that could assist in proper vehicle service. The procedures should not be performed by 'do-ityourselfers'. If you are not a Retailer, do not assume that a condition described affects your vehicle. Contact an authorized
Jaguar service facility to determine whether this bulletin applies to a specific vehicle.

SECTION: 501-12

Front Overhead Console Lamps Do Not Operate As Expected
AFFECTED VEHICLE RANGE:
XJ Range (X351)
Model Year:
2010 Onwards
VIN:
V00047 Onwards

MARKETS:
NAS

CONDITION SUMMARY:
Situation: The front overhead console lamps may not operate as expected (come on while driving and/or are
inoperative).
Cause: This may be caused by issues within the printed circuit board in the lamp assembly.
Action:
In the event of a customer concern of the above, refer to the Repair Procedure outlined below.

PARTS:
C2D30543

PCB Board Kit

Quantity: 1

TOOLS:
Refer to Workshop Manual for any required special tools.

WARRANTY:
NOTE: Repair procedures are under constant review, and therefore times are subject to change;
those quoted here must be taken as guidance only. Always refer to TOPIx to obtain the latest repair
time.
NOTE: DDW requires the use of causal part numbers. Labor only claims must show the causal part
number with a quantity of zero.
DESCRIPTION

SRO

TIME (HOURS)

CONDITION CODE

CAUSAL PART

Roof console circuit board - Renew

86.94.67

0.20

42

C2D17216XXX

NOTE: Normal Warranty policies and procedures apply.

REPAIR PROCEDURE:

WARNING: Hands must be clean and your body grounded prior to touching the new printed circuit
board.

1. Remove the front overhead console lamp assembly (see TOPIx Workshop Manual, Section 501-12).

http://topix.jaguar.jlrint.com/topix/service/document/443310

11/6/2013

Page 2 of 6

Steps 1 and 2 only.

2.

WARNING: The bubble wrap packaging
may be used as a work mat.

NOTE: Make sure no damage is caused
when removing the electrical connectors.
Disconnect the two (2) electrical connectors.

3.

NOTE: Some items removed for clarity.
Move aside the black plastic cover.

4.

NOTE: Make sure no damage is caused
when un-clipping the small printed circuit
boards.
Using a suitable tool, un-clip the three (3) small
circuit boards.

http://topix.jaguar.jlrint.com/topix/service/document/443310

11/6/2013

Page 3 of 6

5.

NOTE: Make sure no damage is caused
when un-clipping the electrical connector.
Using a suitable tool, un-clip the electrical
connector.
Release the two securing clips.

6.

NOTE: Make sure no damage is caused
when removing the printed circuit board.
Remove the main printed circuit board.

7.

NOTE: Make sure all the grease is
removed from the electrical connectors.
Using a suitable clean cloth, remove the grease on
the three (3) electrical connectors.
Using the wipe supplied in the kit, make sure

all the grease is removed from the electrical
connectors.

http://topix.jaguar.jlrint.com/topix/service/document/443310

11/6/2013

Page 4 of 6

8.

CAUTION: When installing the rubber
sleeves, it is important not to damage or split
them.

NOTE: Install all three sleeves from the
top.
Install the three (3) rubber sleeves to the electrical
connectors.
The rubber sleeves must be approximately 2-

3mm from the bottom of the electrical
connector.

9.

CAUTION: Hands must be clean and your body grounded prior to touching the new printed
circuit board.
Change over the three (3) interior light bulbs from the old printed circuit board to the new printed circuit
board.

http://topix.jaguar.jlrint.com/topix/service/document/443310

11/6/2013

Page 5 of 6

10.
NOTE: Make sure no damage is caused
when installing the new printed circuit board.

NOTE: Locate the printed circuit board
into the four locating fixings before clipping
the printed circuit board into position.
Install the new printed circuit board.

11.
NOTE: Make sure no damage is caused
when installing the three small printed
circuit boards
Install the three (3) small printed circuit boards.

12.
NOTE: Make sure the electrical ribbon is
square in the connector before it is fully
engaged.

NOTE: Make sure no damage is caused
when installing the electrical connectors.
Connect the electrical connector.
Push in the two (2) securing clips.

13. Install the black plastic cover.

http://topix.jaguar.jlrint.com/topix/service/document/443310

11/6/2013

Page 6 of 6

14.
NOTE: Make sure no damage is caused
when installing the electrical connectors.
Connect the two (2) electrical connectors.

15. Install the front overhead console lamp (see TOPIx Workshop Manual, Section 501-12).
Steps 2 and 1 only.

16. Check the front overhead console lamps are functioning correctly.

http://topix.jaguar.jlrint.com/topix/service/document/443310

11/6/2013