Technical Service Bulletin
37 Shift quality concerns: harsh 2-3 shift
37 13 94 2033065/1 February 19, 2013.

Model(s)

Year

VIN Range

Vehicle-Specific Equipment

S5

2009

All

4.2 L engine and 6 speed 0B6 transmission

Condition
Shift quality concerns: harsh 2-3 shift.

Technical Background
Incorrect software calibration causes harsh shift points.

Production Solution
Not applicable.

Service
SVM Update Instructions
1. Follow all instructions in the attached TSB, 2011732 00 Software Version Management (SVM), operating
instructions.
2. Update the transmission control module, J217 (02), using the SVM action code as listed in the table below if
necessary.

Model Year

2009

Model

S5

Engine
Old
New
and/or
Old Software Softwar
Software
Transmissio Part Number
e
Part Number
n
Version
4.2L with 0B6
6 speed
8K0927158B
transmission

All

8K0927158B

New
Software
Version
(or higher)

0041

SVM
Action
Code

S502A002

3. Clear adaptations and perform test drive adaptation through GFF.

Page 1 of 2
© 2013 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written
permission of the publisher.

Technical Service Bulletin
Warranty
Claim Type:

Use applicable claim type. If vehicle is outside any warranty, this Technical Service
Bulletin is informational only.

Service Number:

3730

Damage Code:

0039

Labor Operations:

Update software of TCM

3730 2599

40 TU

Charge Battery

2706 8950

10 TU

Perform test drive adaptation

Included in GFF below

GFF to perform test drive adaptation

0150 0000

Time stated on
diagnostic
protocol (Max
100 TU)

Road test prior to service procedure

No allowance

0 TU

Road test after service procedure

No allowance
(included in
adaptation drive)

0 TU

Diagnostic Time:

Technical diagnosis at dealer’s discretion
(Refer to Section 2.2.1.2 and Audi Warranty Online for DADP allowance details)
Claim Comment:

As per TSB #2033065/1

All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures
Manual. Claims are subject to review or audit by Audi Warranty.

Additional Information
The following Technical Service Bulletin will be necessary to complete this procedure:
 TSB 2011732 00 Software Version Management (SVM), operating instructions.
All part and service references provided in this TSB are subject to change and/or removal. Always check with
your Parts Dept. and service manuals for the latest information.

Page 2 of 2
© 2013 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written
permission of the publisher.

Technical Service Bulletin
00 Software Version Management (SVM), operating instructions
00 12 32 2011732/9 February 7, 2012. Supersedes Technical Service Bulletin Group 00 number 10 – 02 dated
March 24, 2010 for reasons listed below.
Model(s)

Year

VIN Range

Vehicle-Specific Equipment

All Audi

2002 on

Not Applicable

Not Applicable

Condition
REVISION HISTORY
Revision

Date

Purpose

9

-

Revised header data (Added model years)
Revised Technical Background
Revised Service (Added image)

8

3/24/2010

Revised Technical Background
Revised Service (Added Response Codes section)

7

5/13/2009

Revised Service (Step 6)

6

12/15/2008

Revised Service (Step 3 – added information concerning use of wireless
VAS 5054A transmitter head)

5

11/17/2008

Revised Title to include Repair Group

4

10/21/2008

Revised Service (Step 3 – added information concerning Windows power
savings settings)

This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management
(SVM) software update for any TSB or Update.
Troubleshooting information is included in the Additional Information section.
Please refer to the upcoming TSBs covering detailed aspects of SVM. They will be listed under group “99”.

Technical Background
SVM was developed with the main goal of ensuring each Audi vehicle has the correct electronic control units with
the correct software versions installed when it leaves the dealership repair facility.

© 2012 Audi of America, Inc.

Page 1 of 10

All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior
expressed written permission of the publisher.

Technical Service Bulletin
SVM is a feature of GFF that has a subset of
functions or components as seen in Figure 1. These
functions are explained below. A VAS 5051B, VAS
5052A, or VAS 6150(A/B/C) diagnostic tool is
required to read out the vehicle control unit data and
send it to the SVM server (also called an “SVM
communication”).

Figure 1. Subset of SVM functions

1. SVM – Specified/actual comparison
Goal: This function is designed to ensure all electronic control units installed in the vehicle have the correct
part numbers, software versions, coding and parameterization. It will not suggest a control unit software
update. During this SVM communication, the part numbers and software versions of the actual control units
installed in the vehicle will be sent to the SVM servers. This “actual” data is then compared to the “specified”
data in the SVM database for a particular vehicle. The specified data stored on the SVM servers is also
referred to as the vehicle “reference”.
What an SVM Spec/Actual can do:
• Document any changes to an electronic control unit’s hardware/software part numbers, hardware/software
versions, and provide feedback to the user if these changes are accepted or rejected.
• When new parts are installed, it will also calculate coding changes or parameterization changes. If a
“hardware replacement suggestion” is given, then a conflict exists with the vehicle reference for that
control unit (i.e. SVM expects a different part number or software version for the control unit in question).
1

• As a rule, SVM will not allow a control unit with the same part number as the original part to be installed if
the new part contains an older software revision. In this situation, SVM will return a hardware change
2
suggestion . In these special cases a new vehicle reference must be manually set by an Audi Product
Support Engineer. Please contact the Technical Assistance Center Helpline if you suspect this is the
case.
2. SVM - Direct Input: SVM code for problem related update
Goal: This function performs any additional functions which cannot be performed with an SVM Spec/Actual.
Those functions include the following.
What an SVM code can do:
• Update the software in a flash-capable control unit if the SVM code is valid for the vehicle.
3

• After the software update is completed, an additional SVM Specified/Actual comparison will be performed
to calculate a new coding and/or parameterization and to document all control unit changes as a new
reference in the SVM database.
• SVM Codes should not be used to update a control unit without knowing the solution(s) the software
update provides. To update control unit software, the technician must first diagnose the condition in the
vehicle and find an applicable TSB that provides a valid SVM Code. Randomly trying out multiple SVM
Codes wastes time and can sometimes cause conflicts in the SVM database.
• SVM codes can also be used to document manual software updates to the vehicle’s systems, as in the
case with MMI Software Package (ZUG) updates. These types of updates are performed manually with a
CD/DVD/SDcard. An SVM code for an MMI update documents the changes in the SVM database and
provides coding and/or parameterization suggestions. It does not perform any software updates.
© 2012 Audi of America, Inc.

Page 2 of 10

All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior
expressed written permission of the publisher.

Technical Service Bulletin
SVM codes for MMI Software Package (ZUG) updates will only complete successfully if every control unit is
updated to the correct software level. This is especially important when a control unit fails/dies during the
manual software update process and is then later replaced, but not updated after it is installed. Since the new
replacement control unit was not updated the SVM code will fail. The replaced control unit must be updated
prior to running the SVM code.
• SVM Exchange (XCHG) Codes can also be used to aid in the installation of new service parts when an
SVM spec/actual cannot code or parameterize the replacement control unit, as with all Audi airbag control
units.
It is critical to note SVM XCHG codes must be run immediately after a new control unit is installed in the
vehicle. If an SVM Spec/Actual is performed instead, it will create an invalid vehicle reference in the SVM
database. Once this occurs the SVM XCHG code will not function properly. The only way to resolve this issue
is to contact the Technical Assistance Center Helpline to have the vehicle reference manually set. To find the
SVM XCHG code, follow the parts bulletin listed in ETKA or search for an applicable Technical Service
Bulletin.
3. SVM - Direct Input: SVM code for vehicle conversion
Goal: This function allows for a factory approved retrofit of additional control unit(s) using a valid SVM Code
for Vehicle Conversion.
• This type of SVM code is documented inside the installation instructions for the control unit and is typically
performed as the last installation step. You can identify an SVM code for conversion by the way it is
named. They are typically named “050XXX”.
4. SVM – Activations
Goal: This function is designed to activate additional features or functions within an already installed control
unit using an Activation Code and possibly additional PIN codes or Customer codes.
• This function is designed with a security system similar to installing a new operating system on a personal
computer. Currently, SVM Activation codes are only being used with navigation map data updates for
vehicles with MMI3G/3G+. The customer no longer needs to purchase the Navigation map data. Instead
the customer must purchase an “Activation Packet” to unlock the map update in the MMI system. The
Activation Packet consists of an Activation Code, Activate Number, and Pin Code. Once the Activation
information is used, it becomes permanently tied to the customer’s vehicle in the SVM database and
cannot be reused with another vehicle.
5. SVM – communication, checking
Goal: This function allows the user to check the VAS Tester’s SVM online connection status to ensure the
tester is communicating with the SVM server.

© 2012 Audi of America, Inc.

Page 3 of 10

All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior
expressed written permission of the publisher.